SVP BIAS-TEE User manual

BI AS I N SERTER TEE
( BI AS-TEE)
M AN UAL V2 .3

Bias I nser ter Tee ( BI AS-TEE)
Page 2
Cont e nts
1Description ................................................................................. 3
2Technical feat ures........................................................................ 4
2.1 BI AS-TEE.............................................................................. 4
2.2 EGG y FGG Lem o connectors.................................................... 5
List of figu r es
Figure 1.1 Bias I nsert ion Tee. BI AS-TEE................................................ 3
Figure 2.1: Connect or pinout .............................................................. 5
List of t a ble s
Table 1 Bias Tee features ................................................................... 4
Table 2: Power supply connect ion t echnical feat ures ............................... 5
Table 3: Power supply connect or pinout ................................................ 5

Bias I nser ter Tee ( BI AS-TEE)
Page 3
1 Descr ipt ion
The Bias Tee is very useful t o give power supply t o an equipm ent connected
to t he ot her end of the coaxial cable, as an LNA or a down-converter.
For it, it has a N m ale connector, a N fem ale connect or and an EGG Lem o
fem ale connector. The N m ale connector should be connect ed to t he receiver
input and t he N fem ale connector t o the LNA’s RF out put t hrough the coaxial
cable. The DC power insert ed through the Lem o connector, support ing a
m axim um of 30 V / 1A.
This equipm ent is protect ed from short -circuit s by m eans of an
aut oreset eable fuse.
The cable wit h FGG Lem o m ale connect or t hat is used t o inser t t he DC pow er
is not supplied with the bias insertion tee (BI AS-TEE).
I n the following figure t he bias insertion tee (BI AS-TEE) is showed, where
the previously m ent ioned connect ions are appreciated:
Figure 1.1 Bias I nsertion Tee. BI AS-TEE

Bias I nser ter Tee ( BI AS-TEE)
Page 4
2 Techn ica l fea t u re s
2 .1 BIAS-TEE
I t e m
Fe at ur e
Frequency range
Fr om 1 0 t o 6 000 MHz
I n ser t ion loss
typ. 0.6 dB @ 10 MHz
typ. 0.6 dB @ 2000 MHz
typ. 0.6 dB @ 4000 MHz
typ. 0.8 dB @ 6000 MHz
Max. RF Power
1 W
I solat ion ( RF-DC)
30dB
Supply voltage range
From + 9V t o + 30V DC
Current Rat ing
500m A m ax.
DC input connector
LEMO 1B of 4 pins
RF&DC connector
N fem ale, 50 Ohm s(Ot h er under r equest )
RF connector
N m ale, 50 Ohm s(Ot her u nder r equest )
Size
Widt h: 50m m
Height : 30m m ( w it hout conn ect or s)
Dept h: 22m m
Table 1 Bias Tee feat ures
2.1.1 Insertion loss

Bias I nser ter Tee ( BI AS-TEE)
Page 5
2 .2 EGG a nd FGG Le m o co n n e ct or s
Pow e r su pply con ne ct or s
I t e m
Feat ur e s
Connect or type
4 pin Lem o 1B
Part num ber ( panel connect or)
ECG.1B.304
Par t n um ber ( cable connect or )
FGG.1B.304.CLAD52
Table 2: Power supply connect ion t echnical features
Pow e r su pply con ne ct or pin ou t
Pin ou t
Figure 2.1: Connector pinout
Pin
D e scr ipt io n
1
GND
2
GND
3
+ VCC
4
+ VCC
Table 3: Power supply connect or pinout

Page 6
N OTES:

Page 7
End not e
At SVP Broadcast Microwave S.L. we m ake a const ant effort t o cont inuously
im prove our equipm ent s and m odels.
For that reason, please underst and t hat there m ay be som e changes in
design, equipm ent and technology. Therefore, we cannot be held liable for
the data, figures and descript ions given in t his datasheet .
The dat asheet’s text, figures and st andards are based on t he inform ation we
had when t he dat asheet was published.
Reprint ing, repr oduct ion and t ranslat ion of all or part of this dat asheet is
forbidden wit hout writ t en perm ission by SVP Broadcast Microwave S.L.
SVP Broadcast Microwave S.L. reserves all copyrights.
All right t o m ake changes are reserved.

SVP Broadcast Microwave reserves t he right to m ake changes t o this user’s
guide and the device wit hout prior warning.
C/ Zubiaur re, 7 baj o
48215 I urret a
Vizcaya – España
Tel: + 34 94 620 3722
Fax: + 34 94 620 4356
svpbm @svpbm .com
www.svpbm .com