SVS-Vistek EVO Tracer Series User manual

3.23.2017
Manual EVO Tracer series
evo1050TR, evo2050TR, evo2150TR, eco4050TR,
evo4070TR, evo8051TR

Manual EVO Tracer series 3.23.2017
Company Information
SVS-VISTEK GMBH
Mühlbachstr. 20
82229 Seefeld
Germany
Tel.: [phone]
Fax: [phone]
Mail: [e-mail]
Web: http://www.svs-vistek.com
This Operation Manual is based on the following standards:
DIN EN 62079
DIN EN ISO 12100
ISO Guide 37
DIN ISO 3864-2
DIN ISO 3864-4
This Operation Manual contains important instructions for safe and
efficient handling of SVCam Cameras (hereinafter referred to as
„camera“). This Operating Manual is part of the camera and must be
kept accessible in the immediate vicinity of the camera for any person
working on or with this camera.
Read carefully and make sure you understand this Operation Manual
prior to starting any work with this camera. The basic prerequisite for safe
work is compliant with all specified safety and handling instructions.
Accident prevention guidelines and general safety regulations shoud be
applied.
Illustrations in this Operation Manual are provided for basic
understanding and can vary from the actual model of this camera. No
claims can be derived from the illustrations in this Operation Manual.
The camera in your possession has been produced with great care and
has been thoroughly tested. Nonetheless, should you have reasons for
complaint, then please contact your local SVS-VISTEK distributor. You will
find a list of distributors in your area under: http://www.svs-
vistek.com/company/distributors/distributors.php
Copyright Protection Statement
(as per DIN ISO 16016:2002-5)
Forwarding and duplicating of this document, as well as using or
revealing its contents are prohibited without written approval. All rights
reserved with regard to patent claims or submission of design or utility
patent.

Contents
iii
Contents
1
Safety Messages ......................................................6
2
Legal Information.....................................................7
3
The EVO Series........................................................8
3.1
Compact Power....................................................... 8
3.2
GigE-Vision features................................................. 8
3.3
Tracer adds dynamic lens control ............................... 9
3.3.1 Tracer with Micro Four Thirds mount .............................. 9
3.4
4IO adds Light and Functionality.............................. 10
4
Getting Started ......................................................11
4.1
Contents of Camera Set.......................................... 11
4.2
Power supply......................................................... 11
4.3
Flashing LED Codes ............................................... 11
4.4
Software............................................................... 12
4.4.1 SVCapture 2.x ............................................................ 12
4.5
Firmware.............................................................. 19
4.5.1 Firmware Update GigE................................................ 19
4.6
GigE IP Setup........................................................ 19
4.7
Driver Circuit Schematics ........................................ 21
5
Connectors ........................................................... 22
5.1
GigE Vision........................................................... 22
5.1.1 Network (TCP/IP) ........................................................ 22
5.1.2 XML Files ................................................................... 25
5.2
Dual GigE Vision ................................................... 25
5.2.1 Network (TCP/IP) ........................................................ 25
5.2.2 Single line operation of dual GigE cameras .................. 26
5.2.3 Teaming Dual GigE .................................................... 27
5.2.4 XML Files ................................................................... 29
5.3
GigE Vision........................................................... 29
5.3.1 Network (TCP/IP) ........................................................ 29
5.3.2 XML Files ................................................................... 33
5.4
Input / output connectors ........................................ 34
5.4.1 M12 I/O connector .................................................... 34
5.4.2 M12 Ethernet Connector ............................................. 34
6
Dimensions ........................................................... 35
6.1
EVO Tracer MFT.................................................... 35
7
Feature-Set ........................................................... 38

Contents
iv
7.1
Basic Understanding............................................... 38
7.1.1 Basic Understanding of CCD Technology ..................... 38
7.1.2 Interline Transfer ......................................................... 39
7.1.3 Global Shutter / Progressive Scan ................................ 40
7.1.4 Frames per Second ..................................................... 41
7.1.5 Acquisition and Processing Time .................................. 41
7.1.6 Exposure .................................................................... 42
7.1.7 Auto Luminance.......................................................... 42
7.1.8 Bit-Depth ................................................................... 43
7.1.9 Color......................................................................... 45
7.1.10 Resolution – active & effective ...................................... 46
7.1.11 Offset ........................................................................ 47
7.1.12 Gain.......................................................................... 48
7.1.13 Image Flip.................................................................. 49
7.1.14 Binning ...................................................................... 50
7.1.15 Decimation ................................................................ 51
7.1.16 Burst Mode ................................................................ 51
7.2
Camera Features................................................... 53
7.2.1 Standard Tap Geometries............................................ 53
7.2.2 Tap Structure.............................................................. 53
7.2.3 Tap Balancing ............................................................ 55
7.2.4 System Clock Frequency .............................................. 56
7.2.5 Temperature Sensor .................................................... 56
7.2.6 Read-Out-Control....................................................... 56
7.2.7 Basic Capture Modes.................................................. 57
7.2.8 LookUp Table............................................................. 60
7.2.9 ROI / AOI.................................................................. 62
7.2.10 Defect Pixel Correction ................................................ 63
7.2.11 Shading Correction..................................................... 64
7.3
I/O Features ......................................................... 65
7.3.1 Assigning I/O Lines – IOMUX ...................................... 65
7.3.2 Strobe Control............................................................ 72
7.3.3 Sequencer.................................................................. 79
7.3.4 PWM ......................................................................... 81
7.3.5 PLC/Logical Operation on Inputs ................................. 83
7.3.6 Serial data interfaces................................................... 84
7.3.7 Trigger-Edge Sensitivity................................................ 87
7.3.8 Debouncing Trigger Signals......................................... 87
7.3.9 Prescale ..................................................................... 89
7.4
IR Cut Filter........................................................... 90
8
Specifications ........................................................ 92
8.1
Evo1050*FLGEA ................................................... 93
8.2
Evo1050*FLGEC ................................................... 95
8.3
Evo2050*FLGEA ................................................... 98
8.4
Evo2050*FLGEC ................................................. 100
8.5
Evo2150*FLGEA ................................................. 103
8.6
Evo2150*FLGEC ................................................. 105
8.7
Evo4050*FLGEA ................................................. 108
8.8
Evo4050*FLGEC ................................................. 110
8.9
Evo4070*FLGEA ................................................. 113

Contents
v
8.10
Evo4070*FLGEC .............................................. 115
8.11
Evo8050*FLGEA .............................................. 118
8.12
Evo8050*FLGEC .............................................. 120
8.13
Evo8051*FLGEA .............................................. 123
8.14
Evo8051*FLGEC .............................................. 125
9
Terms of warranty ................................................ 128
10
Troubleshooting................................................ 129
10.1
FAQ ............................................................... 129
10.2
Support Request Form / Check List ...................... 130
11
IP protection classes .......................................... 132
12
Glossary of Terms ............................................. 133
13
Index of figures ................................................. 136
14
Index ............................................................... 139

SVS-VISTEK–
Compact
Power 6
1Safety Messages
The classification of hazards is made pursuant to ISO 3864-2 and ANSI
Y535.6 with the help of key words.
This Operating Manual uses the following Safety Messages:
Risk of death or serious injury
DANGER!
Danger indicates a hazard with a high level of risk which, if not
avoided will result in death or serious injury.
WARNING!
Warning indicates a hazard with a medium level of risk which, if
not avoided will result in death or serious injury.
CAUTION!
Caution indicates a hazard with a low level of risk which, if not
avoided will result in death or serious injury.
Risk of damage
PROHIBITION!
A black graphical symbol inside a red circular band with a red
diagonal bar defines a safety sign that indicates that an action
shall not be taken or shall be stopped.
CAUTION!
A black graphical symbol inside a yellow triangle defines a
safety sign that indicates a hazard.
MANDATORY ACTION!
A white graphical symbol inside a blue circle defines a safety
sign that indicates that an action shall be taken to avoid a
hazard.
Cross-reference
NOTICE
Provides references and tips
FIGURE 1: TABLE OF SAFETY MESSAGES

SVS-VISTEK–Legal Information
Compact
Power 7
2Legal Information
Information given within the manual accurate as to: March 23, 2017,
errors and omissions excepted.
These products are designed for industrial applications only. Cameras
from SVS-Vistek are not designed for life support systems where
malfunction of the products might result in any risk of personal harm or
injury. Customers, integrators and end users of SVS-Vistek products might
sell these products and agree to do so at their own risk, as SVS-Vistek will
not take any liability for any damage from improper use or sale.
Europe
This camera is CE tested, rules of EN 55022:2010+AC2011 and
EN61000-6-2:2005 apply.
All SVS-VISTEK cameras comply with the recommendation of the
European Union concerning RoHS Rules
USA and Canada
This device complies with part 15 of the FCC Rules. Operation is subject
to the following conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required
to correct the interference at its own expense.
It is necessary to use a shielded power supply cable. You can then use the
“shield contact” on the connector which has GND contact to the camera
housing. This is essential for any use. If not done and camera is destroyed
due to Radio Magnetic Interference (RMI) WARRANTY
is void
!
•
Power:
US/UK and European line adapter can be
delivered. Otherwise use filtered and stabilized DC power
supply.
•Shock & Vibration Resistance is tested: For detailed
Specifications refer to Specification
.

SVS-VISTEK–The EVO Series
Compact
Power 8
3The EVO Series
3.1 Compact Power
Maximum camera technology in the smallest package. With high-end On
Semi sensors the cameras of the SVCam-EVO series offer extraordinary
performance in a very compact housing.
Maximum of high-tech in a minimum enclosure
Our expertise is united to ensure you get a reliable imaging tool for
securing the decisive advantage in your system. Available with resolutions
from 1 up to 12 megapixel with the best CCD and CMOS technology.
The EVO comes with (dual) GigEVision or Camera Link interface. Our
sophisticated sensor knowledge allows for the Camera Link versions even
the extra frame rate – often critical to your advantage. The SVCam-EVO
is also available as Blackline variant.
High power off the shelf
Thanks to the dual GigE connection SVCam-EVO GigE cameras offer a
maximum data rate of 240 MByte/s, fully utilizing the possible data rates
this sensor class (4-tap ON Semiconductor CCDs, or modern first class
CMOS sensors). The GigE Vision and GenICam standards ensure rapid
integration into the application software and enable safe, cost-effective
transmissions of the image data over a distance of 100 m with standard
network technology. Maximum camera technology in the smallest
package.
3.2 GigE-Vision features
GigE Vision is an industrial interface standard for video transmission and
device control over Ethernet networks. It provides numerous software and
hardware advantages for machine vision. Being an industry standard, it
facilitates easy and quick interchangeability between units, shortening
design cycles and reducing development costs.
>Cost effective
>Wide range of „off the shelf“ industrial-standard plugs and cables
>High bandwidth data transfer rate (120 MB/sec per output)
>Up to 100 m range without additional switch
>Wide range of applications in image processing
>Remote service capability
>GenICam compliant
>SDK for Windows XP/10 (32/64 bit) and Linux
In case your camera features a Dual GigE connector, the bandwidth and
data transfer rate are close to double this value. Not every operating
system is supporting link aggregation, though.

SVS-VISTEK
The EVO Series 9
3.3 Tracer adds dynamic lens control
The increasing usage of machine vision in various branches such as
agriculture or packaging and tracking puts new challenges to the
manufacturers of machine vision applications. Very often varying
distances and difficult light conditions make integrating machine vision
into a workflow a hard job. SVS-Vistek pioneered the integration of
variable focus lenses into machine vision.
This chapter applies to the Tracer models (with “TR” in its type name like
the EXO304MGETR)
3.3.1 Tracer with Micro Four Thirds mount
The Tracer accepts this new challenge with a full blown dynamic lens
functionality. Equipped with the well known MFT (Micro Four Thirds)
bayonet, the Tracer supports
>Adjustable focus
>Adjustable zoom
>Adjustable aperture
With this featureset, the Tracer is able to focus extremely fast on various
distances and can do closeups without loss of resolution. With zoom
being relatively slow, aperture and focus adjustment in most cases is done
within 10-20ms (depends on the lens, though).
All of theses functions can be accessed in the application by the camera
programming interface or via GenICam properties. This makes
integration of dynamic lens control into third party software possible with
no effort. Power supply and data control for the lens are done through the
MFT bayonet, so no external cables are visible.
The MFT lenses are optically optimized for sensors up to 1.3”, perfectly
suited for machine vision sensors. The optical construction defined by the
MicroFourThirds consortium, telecentric on the sensor side, provides
smooth images and very low shading. Mechanically built on magnetic
rails in most cases, the stability and repeatability of the lenses is
surprisingly high. A wide selection of suitable lenses for any application is
available. As a surplus, MFT lenses provide excellent optical performance
regarding their price tag.
Due to the size of MFT Bayonet, the Tracer camera size has to be a bit
larger than normal SVS-Vistek cameras do, as the bayonet would not fit
into the std camera housing dimensions. Inside the camera case you’ll
find exactly the same electronics power pack with all of its features and
latest high performance sensors.
Please note, there are versions with CANON EF support and version with
liquid lens support as well, but with limited functionality (e.g. only focus
with liquid lens). These are available on request for some selected Tracer
camera models.

SVS-VISTEK
The EVO Series 10
3.4 4IO adds Light and Functionality
Your SVS-Vistek camera is equipped with the innovative 4IO-interface
allowing full light control, replacing external strobe controllers. Each of
the outputs can be individually configured and managed using pulse-
width modulation. With its high current output, the camera is able to drive
LED lights directly without external light controller.
If you attach any light to the camera, make sure the power supply has
enough power not to fail when the camera is putting light ON.
The integrated sequencer allows multiple exposures with settings to be
programmed, creating new and cost effective options. Logical functions
like AND / OR are supported.
>Up to 4 x open drain high power OUT
>Up to 4 x high voltage IN – TTL up to 25 Volts
>Power MOSFET transistors
>PWM strobe control
>Sequencer for various configurations
>PLC fuctionality with AND, OR and timers
>Safe Trigger (debouncer, prescaler, high low trigger)
Figure 2: Illustration of 4IO concept of switching LEDs (depending on
camera model up to 4 inputs/outputs, see specs)

SVS-VISTEK–Getting Started
Contents
of Camera Set 11
4Getting Started
4.1 Contents of Camera Set
>Camera
>Power supply (if ordered/option)
>DVD
>3D CAD files
>Manuals
>Software: GigE-Kit (Win 32/64 & Linux)
4.2 Power supply
Connect the power supply.
CAUTION! –This camera does not support hotplugging
1. First, connect the data cable.
2.
Then
connect power supply.
When using your own power supply (e.g. 10 -25 V DC) see also Hirose
12-pin for a detailed pin layout of the power connector. For power input
specifications refer to specifications.
4.3 Flashing LED Codes
On power up, the camera will indicate its current status with a flashing
LED on its back. The LED will change color and rhythm.
The meaning of the blinking codes translates as follows:
Table 1 table of flashing LED codes
Flashing
Description
Yellow slow (1Hz)
No Connection
Yellow quickly ( 8 Hz )
Assignment of Network
address
Yellow permanent
Network address assigned
Green permanent
Connected with
application
Green slow (1Hz)
Streaming channel
available
Green quickly ( 8 Hz)
Acquisition enabled
Red slow ( 1 Hz )
Problem with initialization
Red quickly ( 8 Hz)
Camera overheating
Blue permanent
Waiting for trigger
Cyan permanent
Exposure active
Violet permanent
Readout/FVAL

SVS-VISTEK
Getting Started 12
4.4 Software
Further information, documentations, release notes, latest software and
application manuals can be downloaded in the download area on:
https://www.svs-vistek.com/en/login/svs-loginarea-login.php
Depending on the type of camera you bought, several software packages
apply.
4.4.1 SVCapture 2.x
Your SVCam combined software installer including:
>SVCapture 2.x
(a viewer/controler program for SVCam USB3 cameras)
>PC USB3 driver & filter driver
>TL_Driver
(GenICam drivers and transport layer DDLs)
SVCapture 2.x is a XML based software tool provided for free. It is created
to show the capabilities of your SVS-Vistek camera and to show/modify
values to your cam.
Get control of exposure timing, trigger delay, image correction etc. or
control up to 4 LED lights connected to the SVCam directly via the PC.
Use the built-in sequencer to program several intervals executed by one
single trigger impulse.
Figure 3: Screenshot of SVCapture 2.x

SVS-VISTEK
Getting Started 13
Software Setup
Installation prosecco may differ from PC to PC. It is recommended to
install the whole software package.
1. Copy/expand the installation executable file to your hard drive.
2. Run installation
3. Read and accept the terms of license agreement
4. Choose destination folder

SVS-VISTEK
Getting Started 14
5. Install the USB 3.0 Driver
Generic driver included in the windows system will not
match all SVS-VISTEK USB3 Vision features.
6. Start installation
7. System, warning
The installer will modify your system (USB 3.0 driver);
there for windows systems will warn you with an
interrupt.
Accept system modification

SVS-VISTEK
Getting Started 15
Installation will proceed
8. Installation completed

SVS-VISTEK
Getting Started 16
Initialization
FIRST LAUNCH
The software is XML based. So in case there is no Camera connected to
the USB slot, no XML camera properties can be loaded, no values to
control are available.
The screen will be empty.
Connect the camera to your USB 3.0 slot.
Hardware installation will pop up.
Discover the camera with SVCapture 2.x by clicking “discover”.
Connected cameras will be listed.
Choose your camera.

SVS-VISTEK
Getting Started 17
Conform to GenICam all control features will be listed in a flat tree
diagram.

SVS-VISTEK
Getting Started 18
USB 3.0 driver
The USB 3.0 driver
You can find the USB 3.0 driver within your hardware manager:
Firmware update
From time to time make sure your camera is running up to date firmware.
A firmware update tool is integrated in the software.
Internet connection needed.
In case there is no connection contact your local support:

SVS-VISTEK
Getting Started 19
4.5 Firmware
Some features may not have been implemented in older
versions. For updating your camera firmware to the most
recent version, you need the firmware tool and a firmware file
(download it from website, login area) matching your camera
model.
4.5.1 Firmware Update GigE
A separate tool called “Firmware Update Tool.exe” is
provided in the login area of the SVS-Vistek website.
Execute firmware update
>Download the firmware tool and the firmware file from
the SVS-Vistek website.
>Unpack everything into any folder, e.g. “C:\temp”
>Ensure proper network configuration
>Run the GigE update tool
Your camera should appear, choose camera by entering
camera index,
e.g. 1 and press
ENTER.
Figure 4:
searching the
camera to be
updated
Wail until
firmware update
has been
finished
Figure 5: firmware
update has just
been executed
4.6 GigE IP
Setup
Your GigEVision
camera needs a
working network connection. Make sure the camera is attached to the
network and is powered on. Make sure everything is plugged in properly
and that the firewall settings are not blocking the connection to the
camera or SVCapture.

SVS-VISTEK
Getting Started 20
Start SVCapture on your computer. As soon as the camera has booted,
all SVS-Vistek GigE cameras are showing up in the main window.
The cameras will show their IP addresses. In any
case, the last number (1-254) has to be unique in
your subnet. For better understanding of TCP/IP
protocol, refer to applicable documents on the web.
The camera’s behavior is like a standard network
device. If you’re not sure about TCP/IP configuration
or your network, try automatic network configuration
as below.
With right-Click on the selected camera, a menu will show up with 3
options. Depending on whether you want the network changes to be
permanent or not choose one of these options:
1.
Force IP address
(Setup of a network address)
This dialog will put a new IP address (with subnet) to the
camera. This address is volatile, it will be lost as soon the
camera is powered off.
Automatic mode will try to setup a valid network address via
DHCP/LLA
2.
Network settings
(Setup of a network address and save it permanently in the
camera’s memory)
The procedure is the same as above, but the data will be saved
permanently in the camera even when powered off. You might
as well give a clear name inside the network (for the DHCP
server)
3.
Restart automatic network configuration
(do configuration of network IP automatically)