SVS SoundPath Tri-Band Wireless Audio Adapter User manual

TRI-BAND WIRELESS AUDIO
ADAPTER
Owner’s Manual

Thank you for choosing SVS!
Congratulations on bringing home the SVS SoundPath Tri-Band Wireless Audio Adapter, the
best solution available for eliminating subwoofer cable clutter without sacrificing performance.
Because it passes a full-range Left/Right stereo signal, you can also wirelessly connect stereo
speakers, powered surround sound speakers, amplifiers, and any stereo audio component.
The SoundPath Tri-Band Wireless Audio Adapter operates in the 2.4 GHz, 5.2 GHz and 5.8 GHz
bands and is highly resistant to all forms of wireless interference from common household
devices. Seamless switching between channels ensures your subwoofer, speakers or other audio
components will remain connected in even the most congested wireless environments so you can
always enjoy uninterrupted listening experiences.
Installation requires only a few simple steps. If you have questions about subwoofer or speaker
placement, system optimization or installing the SVS SoundPath Tri-Band Wireless Audio Adapter,
please contact the SVS Sound Experts tech support 7-days-a-week.
[email protected] | 877.626.5623 | www.svsound.com
Specifications & Features
Adapter Includes
» Tri-Band Wireless Audio Transmitter
» Tri-Band Wireless Audio Receiver
» Mono RCA to RCA interconnect cable (x2)
» USB A to micro B power cable for power adaptor (x2)
» 5V DC power adapter with USB A Connector (x2)
» Velcro for securing devices (x2)
What You Will Need
» Output device (subwoofer, powered speakers or amplifier)
» Source device (AV receiver, surround processor, or 2-channel pre-amp with a subwoofer pre-out
or L/R line level pre-out)
Specifications
Operating Voltage
RF Frequency Band
Sample Rate
Working Distance
Transmitter analog input level
Receiver analog output level
Frequency Response
Latency
THD+N (dB)
SNR (dB)
Receiver
Minimum power requirement:
4.75V @0.3ARF
Tri-Band (auto switching)
2.4/5.2/5.8 GHz
48kHz
Up to 130 feet; line of sight
N/A
Maximum 1Vrms
6Hz – 20 kHz +/- 0.5 dB
< 19 milliseconds
-70 dB (10Hz – 20kHz)
+ 105 dB 10Hz – 20kHz
Transmitter
Minimum power requirement:
5V @0.5A
Tri-Band (auto switching)
2.4/5.2/5.8 GHz
48kHz
Up to 130 feet; line of sight
Maximum 2Vrms
N/A
6Hz – 20 kHz +/- 0.5 dB
< 19 milliseconds
-70 dB (10Hz – 20kHz)
+ 105 dB 10Hz – 20kHz

General Placement and Set-up Tips
» Place the subwoofer, powered speaker or amplifier at its intended location.
» Try to maintain line-of-sight (no walls or solid barriers) between the transmitter
and receiver for best results.
» Receiver should be within 130 feet of transmitter for best results.
» Avoid placing the transmitter next to devices that could create signal interference, such as mobile
phones, baby monitors, RF wireless phones and Wi-Fi routers.
Connecting the Wireless Transmitter to an AV processor
1. Connect the mono RCA cable to the subwoofer out or LFE channel of the AVR or pre-amp
processor to the R/LFE input on the wireless transmitter.
2. Connect the USB A to Micro B cable to the wireless transmitter and the included 5 VDC power
supply. You can also use an available USB charging port with an output of at least 5V @ 0.5A
3. If using the 5 VDC power supply, connect to nearby power outlet.
Connecting the Wireless Transmitter to a 2-channel stereo pre-amp
1. Connect a stereo RCA cable to the L and R line level pre-outs of the 2-channel stereo
pre-amp and to L and R input on the wireless transmitter. – CABLE NOT SUPPLIED
2. Connect the USB A to Micro B cable to the wireless transmitter and the included 5 VDC
power supply. You can also use an available USB charging port with an output of at
least 5V @0.5A
3. If using the 5 VDC power supply, connect to nearby power outlet.
CENTER
REAR FRONT
SUBWOOFER
(SUB1)
LINE LEVEL OUTPUTS
INPUT OUTPUT
AudioIn
L
Power Pair
R
RECEIVER/PREAMP
AudioIn
(Transmitter)
L
Power Pair
R
LINE LEVEL OUTPUTS REAR FRONT
R
L
RECEIVER/PREAMP
AudioIn
(Transmitter)
L
Power Pair
R

4. If using an SVS subwoofer with a SoundPath Wireless Audio Adapter power output, you can
connect the USB A to Micro B cable to the wireless receiver and directly to the rear panel of
the SVS subwoofer.
Connecting the Wireless Receiver to your Subwoofer
1. Connect the mono RCA cable to the LFE input on the subwoofer and to the R/LFE output on
the wireless receiver.
2. For 2-channel stereo pre-amp applications connect a stereo RCA cable to both the L and R
subwoofer inputs and to the L and R outputs on the wireless receiver. – CABLE NOT
SUPPLIED
3. Connect the USB A to Micro B cable to the wireless receiver and the 5 VDC power supply.
AudioOut
(Receiver)
L
Power Pair
R
ONOFF
R
3V-12V | AC/DC
L
+
VOL
LOW
PASS
LOWPASS
PHASE
PHASE
0°
90°180°
30Hz 40Hz 60Hz 90Hz 140Hz LFE
_
LINE LEVEL
INPUT OUTPUT
TRIGGERINPUT
SVS SOUNDPATH WIRELESS
AUDIOADAPTER
STA-550D
LFE
5V 150mA
RL
INPUT OUTPUT
LFE
AudioOut
L
Power Pair
R
ONOFF
R
3V-12V | AC/DC
L
+
VOL
LOW
PASS
LOW PASS
PHASE
PHASE
0°
90°180°
30Hz 40Hz 60Hz 90Hz 140Hz LFE
_
LINE LEVEL
INPUT OUTPUT
TRIGGER INPUT
SVS SOUNDPATH WIRELESS
AUDIO ADAPTER
STA -55 0D
LFE
5V 150mA

Connecting the Wireless Receiver to Power Amplifiers or Powered
Speakers
1. For 2-channel applications connect the stereo RCA cable to the L and R inputs on the
stereo amplifier or powered speaker inputs and to the L and R outputs on the wireless
receiver - CABLE NOT INCLUDED
2. Connect the USB A to Micro B cable to the wireless receiver and the 5 VDC power supply.
3. Connect the 5 VDC power supply to a nearby outlet.
Pairing the Transmitter and Receiver
1. The transmitter and receiver are synched at the time of manufacture and will pair
automatically when connected and powered on.
2. Successful pairing will be indicated by a steady blue light on the transmitter and receiver.
3. A slow flashing light indicates the units are not paired. To re-pair the units, perform the
following actions:
» Once your transmitter and your receiver are
connected and powered on, press and hold the
PAIR button located on the back of the transmitter
until the blue LED light located on the top of the
unit flashes quickly.
» Within 30 seconds, press and hold the PAIR button located on the back of the receiver.
» When your transmitter and receiver are paired, the wireless status lights on the top of
both units will turn solid blue.
» Your SVS SoundPath Tri-Band Wireless Audio Adapter transmitter and receiver are now
set up and ready to use.
LINE LEVEL INPUTS
SPEAKER LEVEL
OUTPUTS
R
L
TO
SPEAKERS
POWER AMPLIFIER AudioOut
(Receiver)
L
Power Pair
R
INPUT OUTPUT
AudioIn
L
Power Pair
R

FAQs and Troubleshooting
Does my AV processor correct for the latency (time delay) of the wireless unit?
Yes, this will be reflected in a longer than normal subwoofer distance, as shown under the set-up
section of the AV processor. An additional 14 to 20 feet (beyond the actual subwoofer distance)
is normal.
I keep hearing interference artifacts or experiencing signal drop-outs – how can I correct for
this?
Always try to keep a line-of-sight between the transmitter and receiver units with no hard
barriers or walls between them.
Avoid placing other wireless devices near the units like wireless phones, mobile phones, WIFI
routers, baby monitors, etc.
My SoundPath Tri-Band Wireless Audio Adapter is connected and plugged in, but doesn’t seem
to be working.
Verify that the LED status lights on the Transmitter and Receiver are illuminated. If either of
them are off, it might not be receiving power. Make sure there is no visible damage to the
power cable or USB connectors, and check to be sure both are plugged into functioning
electrical outlets. Both Transmitter and Receiver need to have constant power to function
properly.
Warranty & Support
» 5-YEAR UNCONDITIONAL WARRANTY
» SVS offers the industry’s most comprehensive warranty on all our products. SVS warrants the
SoundPath Tri-Band Wireless Audio Adapter and all products to be free from defects in the
workmanship for 5 years from date of purchase.
» This, and all the SVS customer Bill of Rights can be viewed online at:
www.svsound.com/bill-of-rights.
Share Your Thoughts
SVS Sound Experts are standing by Monday to Friday from 9AM-9PM ET, Saturday from
12PM-6PM, and Sunday from 12PM-4PM to assist you with set-up, optimization and any
questions you have about the SoundPath Tri-Band Wireless Audio Adapter. They can be reached
by phone, email or chat via the options below.
[email protected] | 877.626.5623 | www.svsound.com
Facebook.com/svsound
Instagram.com/SVS_Sound
 Youtube.com/c/SVS_Sound
Twitter.com/SVS_Sound

Safety Instructions
» Read these instructions.
» Keep these instructions.
» Heed all warnings.
» Follow all instructions.
» Do not use this apparatus near water.
» Clean only with dry cloth.
» Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
» Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
» Do not defeat the safety purpose of any polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two prongs and a
third grounding point. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
» Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
» Only use attachments/accessories specified by the manufacturer.
» Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
» Unplug this apparatus during lightning storms or when unused for long periods of time.
» Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
» WARNING: To reduce the risk of fire or electric shock, this apparatus should not be exposed
to rain or moisture and objects filled with liquids, such as vases, should not be placed on this
apparatus.
» To completely disconnect this equipment from the mains, disconnect the power supply cord
plug from the receptacle.
» The mains plug of the power supply cord shall remain readily operable.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the products
enclosure that may be of sufficient magnitude to constitute risk of electric shock to
persons.
The exclamation point within a triangle is intended to alert the user to the presence of
importance operating and maintenance {servicing) instructions in the literature
companying the product.
The equipment is a Class II or double insulated electrical appliance. It has been designed
in such a way that it does not require a safety connection to electrical earth.

[phone] | Youngstown, OH, USA | svsound.com