Extron electronics RGB 580xi AAP Series User manual

Setup Guide — RGB 580xi AAP
and RGB 580xi CC AAP Series
This guide provides basic instructions for an experienced
installer to set up and operate the Extron RGB 580xi AAP
and RGB 580xi CC AAP.
Installation
The AAP device should be cabled before attaching the AAP
device to a faceplate or wall plate.
CInstallation and service must be performed by authorized personnel only.
Step 1 — Power down
Turn off or disconnect all equipment from power sources.
Step 2 — Connect the rear panel cables
Connect the cables to the AAP device’s rear connectors.
NAlthough the control cable, LED, and audio assemblies come prewired to the captive screw
connectors, any subsequent cable assembly replacement requires the following instructions.
1
3
Example of AAP device rear connectors
2
Red
Black
White Yellow
Pink
Orange
Green
Gray
Brown
Lt. Blue
Purple
J4 J2
Example of Cable Cubby AAP device rear connectors
1 2
To cable the captive screw connectors, refer to the following diagrams and orient the wires
according to the view angle of the captive screws. Use the Extron VGA and control cable
assembly and refer to the color of each wire for signal identification.
aControl connector (J4) — This connector is used for contact closure and horizontal shift
signals. Wire the appropriate connector as shown below.
Horizontal shift +(green)
Horizontal shift ground (gray)
Horizontal shift –(brown)
Contact closure +(light blue)
Contact closure – (purple)
Horizontal shift +(green)
Horizontal shift ground (gray)
Horizontal shift –(brown)
Contact closure +(light blue)
Contact closure – (purple)
Pin 1
Pin 1
(Continued on reverse side.)

Setup Guide — RGB 580xi AAP and CC AAP Series
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2009 Extron Electronics. All rights reserved.
68-537-50
Rev. A
11 09
bLED connector (J2) — This connector is used for powering the green/amber LED. Wire
the appropriate connector as shown below.
Green LED (pink)
LED ground (yellow)
Amber LED (orange)
Pin 1 Pin 1
Green LED (pink)
LED ground (yellow)
Amber LED (orange)
cAudio output connector — This connector is used for unbalanced stereo
audio output. Wire the connector as shown below.
Pin 1
Audio right (red)
A
udio ground (black)
Audio right (white)
Step 3 — Audio connect
Wire a 3.5 mm stereo plug for unbalanced audio input
as shown at right.
Step 4 — Mount the AAP
Insert the AAP device’s screws through the holes in the AAP double-space faceplate, the AAP
wall plate, or the Cable Cubby AAP shelf bracket. Secure the AAP device to the faceplate/wall
plate/shelf bracket with the provided captive washers and #4-40 nuts. See the examples below.
Cable
Cable
Clamp
RGB 580xi SI AAP
AAP 102
AAP 102
#4-40 Nut w/ Captive
Washer
RGB 580xi SI AAP
COMPUTER
AUDIO
H SHIFT
INPUT
SELECT
Wall Plate
Operation
The RGB 580xi AAP models S, SI, CCS, and CCSI have a front panel horizontal shift control
knob. The SI and CCSI models also have an input select button.
Horizontal shift control knob — While viewing the displayed image, rotate this control to
move the image to the right or left on the screen. The power/signal LED will flash green
whenever the minimum and maximum limits of this control are reached.
Input select button — Pressing this button results in contact closure between pins A and B of
the contact closure connector on the front panel of the RGB 580xi remote interface. This button
can also be used for direct control of any Extron contact closure-controlled switcher, or as a
direct connection to an external control system.
RGB 580xi CCSI AAP
Cable Cubby
INPUT
SELECT
H. SHIFT
Sleeve ( )
Ring (R)
Tip (L)