Swann SI-100E User manual

OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
1
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
Thank you for purchasing our Swan ice shaving machine. For correct use,carefully
read and understand this entire Instruction Manual. Furthermore, after reading it,
the manual should be kept so you can refer to it again in case of necessity. In case
the machine is resold to another party, be sure that it is sold together with the
Instruction manual.
CAUTION .... EXPOSED SHARP OBJECTS INSIDE
WARNING
POTENTIAL RISK OF FIRE, ELECTRIC SHOCK AND PERSONAL
INJURY EXISTS. CHECK WIRING AND SET PRONGS INTO ICE
BLOCK FIRMLY TO AVOID INJURY.
UNPLUG MACHINE WHEN NOT IN USE FROM POWER
SOURCE.
SwanIceShavers.com
Thank you for purchasing our Swan ice shaving machine. For correct use, carefully read
and understand this enre instrucon manual. Furthermore, aer reading it, the manual
should be kept so you can refer to it again in case of necessity. In case the machine is resold
to another party, be sure that it is sold together with the instrucon manual.
BLOCK ICE SHAVER
ELECTRIC TYPE MODEL SI-100E for Block Ice
WARNING: POTENTIAL RISK OF FIRE, ELECTRIC SHOCK AND PERSONAL INJURY EXISTS. CHECK WIRING AND SET
PRONGS INTO ICE BLOCK FIRMLY TO AVOID INJURY. UNPLUG MACHINE FROM POWER SOUCE WHEN NOT IN USE.
CAUTION: EXPOSED SHARP OBJECTS INSIDE
INSTRUCTION MANUAL

OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
2
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
Read the following instructions carefully before use.
IMPORTANT BEFORE USE:
BRAKE ADJUSTMENT-Reset before you begin as settings may have
moved during shipping.
1. Remove the rubber plug on the front of the head cover.
2. Crank handle to raise Ice Block Holder all the way up.
3. Take a straight edge screwdriver and turn Brake Adjustment Screw counter-clockwise, slowly.
4. When the Ice Block Holder drops, stop.
5. Turn Brake Adjustment Screw clockwise with screw driver 2 full turns. This should be set to the perfect tension to
shave ice properly.
6. Test the pressure by turning the crank up and down. It should be firm, not very easy to crank up and down.
•Children or person who do not thoroughly understand the product should not be allowed to operate this machine.
•Use 15A 115V power source. If using agenerator, make sure that is rated high enough to provide sufficient
electricity for everything needed for your operation.
•Extension Cord.If needed, always use athree-prong type grounded cord. To determine anextension cord’s
capacity, consider both the length and the wire gauge. Every extra foot of cord increases the electrical resistance,
which decreases the power the cord candeliver to the connectedmachine. Excessive cord lengthcould overheat and
damage the motor. Best to use a cord that’s only as long as needed (maximum 25 feet). If an extension cord is
required for outdoor applications, use a 12-gauge (heavy duty) cord rated for outdoor use.
•Place the machine on astrong and flat horizontal surface or location where dripping water is not aproblem.
•The blade and spikes are very dangerous. They must be handled with extreme care.
•Place the block ice on center of the shaving disc with the flat side up and be sure the spikes on the block ice holder
are deeply embedded in the ice before use. Imperfect placement or down pressure on the block ice will cause the
ice to move off the shaving area which is dangerous.
•Ice stored in freezer should not be used immediately for shaving as it could damage the blade.Let the ice thaw
(15-20 minutes) and become semi-transparent before use.
•As the cover of the product is made of plastic, do not place the machine where it is exposed to direct heating
equipment or use paint thinner or similar type of product to clean the cover as these products will disfigurethe
plastic.
•Replace the blade every 3,000 shaves or if chipped or when it becomes dull. Lubricate Main Shaft and Gear Box
monthly.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
3
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
•Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick,this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2. Make sure that the blade is in the down position, below the Shaving Plate opening. Place ice block flat side up, and center
on the shaving plate.This may require a couple oftries.
3. Turn the Ice Block Holder Crank counter-clockwise to lower the Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder prongs are firmly imbedded inthe ice. The polycarbonate shieldshouldbe turned horizontally to the
front.

www.Snobiz.com 1(800)-742-8342 [email protected]
3
SWAN SI-100E OWNERS MANUAL 2020.1
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
2
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
Read the following instructions carefully before use.
IMPORTANT BEFORE USE:
BRAKE ADJUSTMENT-Reset before you begin as settings may have
moved during shipping.
1. Remove the rubber plug on the front of the head cover.
2. Crank handle to raise Ice Block Holder all the way up.
3. Take a straight edge screwdriver and turn Brake Adjustment Screw counter-clockwise, slowly.
4. When the Ice Block Holder drops, stop.
5. Turn Brake Adjustment Screw clockwise with screw driver 2 full turns. This should be set to the perfect tension to
shave ice properly.
6. Test the pressure by turning the crank up and down. It should be firm, not very easy to crank up and down.
•Children or person who do not thoroughly understand the product should not be allowed to operate this machine.
•Use 15A 115V power source. If using a generator, make sure that is rated high enough to provide sufficient
electricity for everything needed for your operation.
•Extension Cord. If needed, always use a three-prong type grounded cord. To determine an extension cord’s
capacity, consider both the length and the wire gauge. Every extra foot of cord increases the electrical resistance,
which decreases the power the cord can deliver to the connected machine. Excessive cord length could overheat and
damage the motor. Best to use a cord that’s only as long as needed (maximum 25 feet). If an extension cord is
required for outdoor applications, use a 12-gauge (heavy duty) cord rated for outdoor use.
•Place the machine on a strong and flat horizontal surface or location where dripping water is not a problem.
•The blade and spikes are very dangerous. They must be handled with extreme care.
•Place the block ice on center of the shaving disc with the flat side up and be sure the spikes on the block ice holder
are deeply embedded in the ice before use. Imperfect placement or down pressure on the block ice will cause the
ice to move off the shaving area which is dangerous.
•Ice stored in freezer should not be used immediately for shaving as it could damage the blade. Let the ice thaw
(15-20 minutes) and become semi-transparent before use.
•As the cover of the product is made of plastic, do not place the machine where it is exposed to direct heating
equipment or use paint thinner or similar type of product to clean the cover as these products will disfigure the
plastic.
•Replace the blade every 3,000 shaves or if chipped or when it becomes dull. Lubricate Main Shaft and Gear Box
monthly.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
3
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
•Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick, this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2. Make sure that the blade is in the down position, below the Shaving Plate opening. Place ice block flat side up, and center
on the shaving plate.This may require a couple oftries.
3. Turn the Ice Block Holder Crank counter-clockwise to lower the Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder prongs are firmly imbedded inthe ice. The polycarbonate shieldshouldbe turned horizontally to the
front.

www.SnoBiz.com 1(800)-742-8342 [email protected]
4
SWAN SI-100E OWNERS MANUAL 2020.1
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
4
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
4. Turn on the Motor Switch. The Main Shaft Ice Block Holder will start to revolve. If ice block wobbles as it rotates, turn off
power switch and re-center the ice block.
5. Turn the Blade Adjustment Knob located on the left side ofShaving Plate Frame counter-clockwise SLOWLY.This will
raise the blade, allowing it to shave the ice. The higher the blade is raised, the coarser and faster the ice will come out.
6. After the texture ofshave ice isadjusted, hold the cup under the outlet of shave ice.
7. Turn off Motor Switch after use.
8. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
3
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
•Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick,this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2. Make sure that the blade is in the down position, below the Shaving Plate opening. Place ice block flat side up, and center
on the shaving plate.This may require a couple oftries.
3. Turn the Ice Block Holder Crank counter-clockwise to lower the Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder prongs are firmly imbedded inthe ice. The polycarbonate shieldshouldbe turned horizontally to the
front.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
3
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
•Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick,this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2. Make sure that the blade is in the down position, below the Shaving Plate opening. Place ice block flat side up, and center
on the shaving plate.This may require a couple oftries.
3. Turn the Ice Block Holder Crank counter-clockwise to lower the Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder prongs are firmly imbedded inthe ice. The polycarbonate shieldshouldbe turned horizontally to the
front.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
4
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
4. Turn on the Motor Switch. The Main Shaft Ice Block Holder will start to revolve. If ice block wobbles as it rotates, turn off
power switch and re-center the ice block.
5. Turn the Blade Adjustment Knob located on the left side ofShaving Plate Frame counter-clockwise SLOWLY.This will
raise the blade, allowing it to shave the ice. The higher the blade is raised, the coarser and faster the ice will come out.
6. After the texture ofshave ice isadjusted, hold the cup under the outlet of shave ice.
7. Turn off Motor Switch after use.
8. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
3
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
•Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick,this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2. Make sure that the blade is in the down position, below the Shaving Plate opening. Place ice block flat side up, and center
on the shaving plate. This may require a couple of tries.
3. Turn the Ice Block Holder Crank counter-clockwise to lower the Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder prongs are firmly imbedded inthe ice. The polycarbonate shieldshouldbe turned horizontally to the
front.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
3
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
•Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick,this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2. Make sure that the blade is in the down position, below the Shaving Plate opening. Place ice block flat side up, and center
on the shaving plate.This may require a couple oftries.
3. Turn the Ice Block Holder Crank counter-clockwise to lower the Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder prongs are firmly imbedded in the ice. The polycarbonate shield should be turned horizontally to the
front.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
5
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
9. If ice block wobbles as it rotates, turn off power switch and re-center the ice block.
10. Remove the ice block.
BLADE ADJUSTMENT
1. The Blade isrecessed below the surface ofthe Shaving Disc when the Blade Adjustment Dial is turned to 0.
2. To raise the Blade, slowly turn the Blade Adjustment Knob counter-clockwise.
3. Set the Blade Adjustment Dial on 1for fine shaving and 6 for roughest shaving.
Note: THE DIAL WILL INDICATE 0WHENTHE BLADE ADJUSTMENT KNOB IS TURNED CLOCKWISE ALL THE WAY AND
STOPS PRODUCING ICE.
BLADE REPLACEMENT
1. Turn the Blade Adjustment Knob right all the way until it stops.
2. Unscrew the two Phillips-screws. Remove the Blade Holder and blade.
Important: DO NOT INTERFERE WITH THE CENTER SLOTTED SCREW.
3. Place the new Blade accurately on the Standard Level Guide Screws on the Blade Support.
4. Put the Phillips-screw in and slowly screw it on so the blade will not lift up from the Standard Level Guide Screws.
Screw it on tight.
*If both ends of the Blade are not accurately set on the Standard Level Guide Screws, the ice will not shave correctly.

www.Snobiz.com 1(800)-742-8342 [email protected]
5
SWAN SI-100E OWNERS MANUAL 2020.1
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
4
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
4. Turn on the Motor Switch. The Main Shaft Ice Block Holder will start to revolve. If ice block wobbles as it rotates, turn off
power switch and re-center the ice block.
5. Turn the Blade Adjustment Knob located on the left side of Shaving Plate Frame counter-clockwise SLOWLY. This will
raise the blade, allowing it to shave the ice. The higher the blade is raised, the coarser and faster the ice will come out.
6. After the texture of shave ice is adjusted, hold the cup under the outlet of shave ice.
7. Turn off Motor Switch after use.
8. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
3
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
•Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick,this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2. Make sure that the blade is in the down position, below the Shaving Plate opening. Place ice block flat side up, and center
on the shaving plate.This may require a couple oftries.
3. Turn the Ice Block Holder Crank counter-clockwise to lower the Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder prongs are firmly imbedded inthe ice. The polycarbonate shieldshouldbe turned horizontally to the
front.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
3
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
•Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick,this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2. Make sure that the blade is in the down position, below the Shaving Plate opening. Place ice block flat side up, and center
on the shaving plate.This may require a couple oftries.
3. Turn the Ice Block Holder Crank counter-clockwise to lower the Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder prongs are firmly imbedded inthe ice. The polycarbonate shieldshouldbe turned horizontally to the
front.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
4
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
4. Turn on the Motor Switch. The Main Shaft Ice Block Holder will start to revolve. If ice block wobbles as it rotates, turn off
power switch and re-center the ice block.
5. Turn the Blade Adjustment Knob located on the left side ofShaving Plate Frame counter-clockwise SLOWLY.This will
raise the blade, allowing it to shave the ice. The higher the blade is raised, the coarser and faster the ice will come out.
6. After the texture ofshave ice isadjusted, hold the cup under the outlet of shave ice.
7. Turn off Motor Switch after use.
8. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
3
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
•Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick,this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2. Make sure that the blade is in the down position, below the Shaving Plate opening. Place ice block flat side up, and center
on the shaving plate.This may require a couple oftries.
3. Turn the Ice Block Holder Crank counter-clockwise to lower the Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder prongs are firmly imbedded inthe ice. The polycarbonate shieldshouldbe turned horizontally to the
front.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
3
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
•Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick,this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn the Ice Block Holder Crank clockwise to raise the Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2. Make sure that the blade is in the down position, below the Shaving Plate opening. Place ice block flat side up, and center
on the shaving plate.This may require a couple oftries.
3. Turn the Ice Block Holder Crank counter-clockwise to lower the Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder prongs are firmly imbedded inthe ice. The polycarbonate shieldshouldbe turned horizontally to the
front.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
5
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
9. If ice block wobbles as it rotates, turn off power switch and re-center the ice block.
10. Remove the ice block.
BLADE ADJUSTMENT
1. The Blade isrecessed below the surface ofthe Shaving Disc when the Blade Adjustment Dial is turned to 0.
2. To raise the Blade, slowly turn the Blade Adjustment Knob counter-clockwise.
3. Set the Blade Adjustment Dial on 1for fine shaving and 6 for roughest shaving.
Note: THE DIAL WILL INDICATE 0WHENTHE BLADE ADJUSTMENT KNOB IS TURNED CLOCKWISE ALL THE WAY AND
STOPS PRODUCING ICE.
BLADE REPLACEMENT
1. Turn the Blade Adjustment Knob right all the way until it stops.
2. Unscrew the two Phillips-screws. Remove the Blade Holder and blade.
Important: DO NOT INTERFERE WITH THE CENTER SLOTTED SCREW.
3. Place the new Blade accurately on the Standard Level Guide Screws on the Blade Support.
4. Put the Phillips-screw in and slowly screw it on so the blade will not lift up from the Standard Level Guide Screws.
Screw it on tight.
*If both ends of the Blade are not accurately set on the Standard Level Guide Screws, the ice will not shave correctly.

www.SnoBiz.com 1(800)-742-8342 [email protected]
6
SWAN SI-100E OWNERS MANUAL 2020.1
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
6
BRAKE ADJUSTMENT-Adjust when ice is not shaving correctly.
1. Remove the rubber plug onthe front of the head cover.
2. Raise Ice Block Holder Crank Clockwise.
3. Take a straight edge screwdriver and turnBrake Adjustment Screw counterclockwise, slowly.
4. When the Ice Block Holder Crank drops, stop.
5. Turn Brake Adjustment Screw clockwise with screwdriver 2-2.5 full turns.
6. Test the pressure ofthe Crank. It should be firm to turn.
PROTECTOR
A Push Button Switch (Protector) is located on the left side of the Head Cover. If something is wrong with the blade
section or the revolving section, the machine will automatically stop to prevent overheating and damage the motor. In
such case, turn off the Power Source Switch (Disconnect the plug) and after the cause is removed. Plug incordand push
the protector. TheMotor will automatically start again.
TO MAINTAIN SANITATION WITHOUT TOOLS
For periodic cleaning of the Shaving Plate as well as adjacent area in the food zone, removal is possible as follows.
1. By removing the 4 thumbscrews located on the underside of the plate, the Shaving Plate can be easily removed
by pushing it up.
2. To clean the Shaving Plate Frame and the adjacent area, remove the 4 thumbscrews holding the Front Cover (2
thumbscrews on each side), then pull the Front Cover towards the user to remove. The entire food zone can be
easily cleaned.
3. Brake Shoe and worm gear should not have any grease on the metals. This is caused by Hot weather conditions
and heavy use of the shaver. Simple use a dry rag, turn the machine on, and wipe the parts clean.
STORAGE AFTER SEASON
Wipe off moisture with piece of cloth, then wipe again with dry piece of cloth. Remove Blade, clean and lubricate
with cooking oil, the wrap in foil paper before storage. Remove all soiled oil from the MainShaft and lubricate with
grease approved by FDA for the lubrication of food processing machinery. Do not use cooking oil. ALWAYS unplug the
machine when not in use.
SPECIFICATIONS*
Dimensions: 25-3/4” high x11-1/8” wide x 15-1/8” deep
Weight: 61.7 lbs.
Shaving Capacity: 4.84 to 5.5 lbs. per minute
Motor:115V, 200W
Power Requirement: 210W, 60Hz
Accessories: Spare Blade (1), Grease oil (1), Drain Hose (1)
*Specifications are subject to change without notice for further design and performance improvement.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
6
BRAKE ADJUSTMENT-Adjust when ice is not shaving correctly.
1. Remove the rubber plug onthe front of the head cover.
2. Raise Ice Block Holder Crank Clockwise.
3. Take a straight edge screwdriver and turnBrake Adjustment Screw counterclockwise, slowly.
4. When the Ice Block Holder Crank drops, stop.
5. Turn Brake Adjustment Screw clockwise with screwdriver 2-2.5 full turns.
6. Test the pressure ofthe Crank. It should be firm to turn.
PROTECTOR
A Push Button Switch (Protector) is located on the left side of the Head Cover. If something is wrong with the blade
section or the revolving section, the machine will automatically stop to prevent overheating and damage the motor. In
such case, turn off the Power Source Switch (Disconnect the plug) and after the cause is removed. Plug incordand push
the protector. TheMotor will automatically start again.
TO MAINTAIN SANITATION WITHOUT TOOLS
For periodic cleaning of the Shaving Plate as well as adjacent area in the food zone, removal is possible as follows.
1. By removing the 4 thumbscrews located on the underside of the plate, the Shaving Plate can be easily removed
by pushing it up.
2. To clean the Shaving Plate Frame and the adjacent area, remove the 4 thumbscrews holding the Front Cover (2
thumbscrews on each side), then pull the Front Cover towards the user to remove. The entire food zone can be
easily cleaned.
3. Brake Shoe and worm gear should not have any grease on the metals. This is caused by Hot weather conditions
and heavy use of the shaver. Simple use a dry rag, turn the machine on, and wipe the parts clean.
STORAGE AFTER SEASON
Wipe off moisture with piece of cloth, then wipe again with dry piece of cloth. Remove Blade, clean and lubricate
with cooking oil, the wrap in foil paper before storage. Remove all soiled oil from the MainShaft and lubricate with
grease approved by FDA for the lubrication of food processing machinery. Do not use cooking oil. ALWAYS unplug the
machine when not in use.
SPECIFICATIONS*
Dimensions: 25-3/4” high x11-1/8” wide x 15-1/8” deep
Weight: 61.7 lbs.
Shaving Capacity: 4.84 to 5.5 lbs. per minute
Motor:115V, 200W
Power Requirement: 210W, 60Hz
Accessories: Spare Blade (1), Grease oil (1), Drain Hose (1)
*Specifications are subject to change without notice for further design and performance improvement.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
5
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
9. If ice block wobbles as it rotates, turn off power switch and re-center the ice block.
10. Remove the ice block.
BLADE ADJUSTMENT
1. The Blade is recessed below the surface of the Shaving Disc when the Blade Adjustment Dial is turned to 0.
2. To raise the Blade, slowly turn the Blade Adjustment Knob counter-clockwise.
3. Set the Blade Adjustment Dial on 1 for fine shaving and 6 for roughest shaving.
Note: THE DIAL WILL INDICATE 0 WHEN THE BLADE ADJUSTMENT KNOB IS TURNED CLOCKWISE ALL THE WAY AND
STOPS PRODUCING ICE.
BLADE REPLACEMENT
1. Turn the Blade Adjustment Knob right all the way until it stops.
2. Unscrew the two Phillips-screws. Remove the Blade Holder and blade.
Important: DO NOT INTERFERE WITH THE CENTER SLOTTED SCREW.
3. Place the new Blade accurately on the Standard Level Guide Screws on the Blade Support.
4. Put the Phillips-screw in and slowly screw it on so the blade will not lift up from the Standard Level Guide Screws.
Screw it on tight.
*If both ends of the Blade are not accurately set on the Standard Level Guide Screws, the ice will not shave correctly.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
5
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
9. If ice block wobbles as it rotates, turn off power switch and re-center the ice block.
10. Remove the ice block.
BLADE ADJUSTMENT
1. The Blade isrecessed below the surface ofthe Shaving Disc when the Blade Adjustment Dial is turned to 0.
2. To raise the Blade, slowly turn the Blade Adjustment Knob counter-clockwise.
3. Set the Blade Adjustment Dial on 1for fine shaving and 6 for roughest shaving.
Note: THE DIAL WILL INDICATE 0WHENTHE BLADE ADJUSTMENT KNOB IS TURNED CLOCKWISE ALL THE WAY AND
STOPS PRODUCING ICE.
BLADE REPLACEMENT
1. Turn the Blade Adjustment Knob right all the way until it stops.
2. Unscrew the two Phillips-screws. Remove the Blade Holder and blade.
Important: DO NOT INTERFERE WITH THE CENTER SLOTTED SCREW.
3. Place the new Blade accurately on the Standard Level Guide Screws on the Blade Support.
4. Put the Phillips-screw in and slowly screw it on so the blade will not lift up from the Standard Level Guide Screws.
Screw it on tight.
*If both ends of the Blade are not accurately set on the Standard Level Guide Screws, the ice will not shave correctly.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
6
BRAKE ADJUSTMENT-Adjust when ice is not shaving correctly.
1. Remove the rubber plug on the front of the head cover.
2. Raise Ice Block Holder Crank Clockwise.
3. Take a straight edge screwdriver and turn Brake Adjustment Screw counterclockwise, slowly.
4. When the Ice Block Holder Crank drops, stop.
5. Turn Brake Adjustment Screw clockwise with screwdriver 2-2.5 full turns.
6. Test the pressure of the Crank. It should be firm to turn.
PROTECTOR
A Push Button Switch (Protector) is located on the left side of the Head Cover. If something is wrong with the blade
section or the revolving section, the machine will automatically stop to prevent overheating and damage the motor. In
such case, turn off the Power Source Switch (Disconnect the plug) and after the cause is removed. Plug incordand push
the protector. TheMotor will automatically start again.
TO MAINTAIN SANITATION WITHOUT TOOLS
For periodic cleaning of the Shaving Plate as well as adjacent area in the food zone, removal is possible as follows.
1. By removing the 4 thumbscrews located on the underside of the plate, the Shaving Plate can be easily removed
by pushing it up.
2. To clean the Shaving Plate Frame and the adjacent area, remove the 4 thumbscrews holding the Front Cover (2
thumbscrews on each side), then pull the Front Cover towards the user to remove. The entire food zone can be
easily cleaned.
3. Brake Shoe and worm gear should not have any grease on the metals. This is caused by Hot weather conditions
and heavy use of the shaver. Simple use a dry rag, turn the machine on, and wipe the parts clean.
STORAGE AFTER SEASON
Wipe off moisture with piece of cloth, then wipe again with dry piece of cloth. Remove Blade, clean and lubricate
with cooking oil, the wrap in foil paper before storage. Remove all soiled oil from the MainShaft and lubricate with
grease approved by FDA for the lubrication of food processing machinery. Do not use cooking oil. ALWAYS unplug the
machine when not in use.
SPECIFICATIONS*
Dimensions: 25-3/4” high x11-1/8” wide x 15-1/8” deep
Weight: 61.7 lbs.
Shaving Capacity: 4.84 to 5.5 lbs. per minute
Motor:115V, 200W
Power Requirement: 210W, 60Hz
Accessories: Spare Blade (1), Grease oil (1), Drain Hose (1)
*Specifications are subject to change without notice for further design and performance improvement.
TUNE-UP KITS & COMPLETE MAINTENANCE
VIDEOS ARE AVAILABLE AT:
SnoBiz :YouTube

www.Snobiz.com 1(800)-742-8342 [email protected]
7
SWAN SI-100E OWNERS MANUAL 2020.1
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
6
BRAKE ADJUSTMENT-Adjust when ice is not shaving correctly.
1. Remove the rubber plug onthe front of the head cover.
2. Raise Ice Block Holder Crank Clockwise.
3. Take a straight edge screwdriver and turnBrake Adjustment Screw counterclockwise, slowly.
4. When the Ice Block Holder Crank drops, stop.
5. Turn Brake Adjustment Screw clockwise with screwdriver 2-2.5 full turns.
6. Test the pressure ofthe Crank. It should be firm to turn.
PROTECTOR
A Push Button Switch (Protector) is located on the left side of the Head Cover. If something is wrong with the blade
section or the revolving section, the machine will automatically stop to prevent overheating and damage the motor. In
such case, turn off the Power Source Switch (Disconnect the plug) and after the cause is removed. Plug in cord and push
the protector. The Motor will automatically start again.
TO MAINTAIN SANITATION WITHOUT TOOLS
For periodic cleaning of the Shaving Plate as well as adjacent area in the food zone, removal is possible as follows.
1. By removing the 4 thumbscrews located on the underside of the plate, the Shaving Plate can be easily removed
by pushing it up.
2. To clean the Shaving Plate Frame and the adjacent area, remove the 4 thumbscrews holding the Front Cover (2
thumbscrews on each side), then pull the Front Cover towards the user to remove. The entire food zone can be
easily cleaned.
3. Brake Shoe and worm gear should not have any grease on the metals. This is caused by Hot weather conditions
and heavy use of the shaver. Simple use a dry rag, turn the machine on, and wipe the parts clean.
STORAGE AFTER SEASON
Wipe off moisture with piece of cloth, then wipe again with dry piece of cloth. Remove Blade, clean and lubricate
with cooking oil, the wrap in foil paper before storage. Remove all soiled oil from the MainShaft and lubricate with
grease approved by FDA for the lubrication of food processing machinery. Do not use cooking oil. ALWAYS unplug the
machine when not in use.
SPECIFICATIONS*
Dimensions: 25-3/4” high x11-1/8” wide x 15-1/8” deep
Weight: 61.7 lbs.
Shaving Capacity: 4.84 to 5.5 lbs. per minute
Motor:115V, 200W
Power Requirement: 210W, 60Hz
Accessories: Spare Blade (1), Grease oil (1), Drain Hose (1)
*Specifications are subject to change without notice for further design and performance improvement.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
6
BRAKE ADJUSTMENT-Adjust when ice is not shaving correctly.
1. Remove the rubber plug onthe front of the head cover.
2. Raise Ice Block Holder Crank Clockwise.
3. Take a straight edge screwdriver and turnBrake Adjustment Screw counterclockwise, slowly.
4. When the Ice Block Holder Crank drops, stop.
5. Turn Brake Adjustment Screw clockwise with screwdriver 2-2.5 full turns.
6. Test the pressure ofthe Crank. It should be firm to turn.
PROTECTOR
A Push Button Switch (Protector) is located on the left side of the Head Cover. If something is wrong with the blade
section or the revolving section, the machine will automatically stop to prevent overheating and damage the motor. In
such case, turn off the Power Source Switch (Disconnect the plug) and after the cause is removed. Plug incordand push
the protector. TheMotor will automatically start again.
TO MAINTAIN SANITATION WITHOUT TOOLS
For periodic cleaning of the Shaving Plate as well as adjacent area in the food zone, removal is possible as follows.
1. By removing the 4 thumbscrews located on the underside of the plate, the Shaving Plate can be easily
removed
by pushing it up.
2. To clean the Shaving Plate Frame and the adjacent area, remove the 4 thumbscrews holding the Front Cover (2
thumbscrews on each side), then pull the Front Cover towards the user to remove. The entire food zone can be
easily cleaned.
3. Brake Shoe and worm gear should not have any grease on the metals. This is caused by Hot weather conditions
and heavy use of the shaver. Simple use a dry rag, turn the machine on, and wipe the parts clean.
STORAGE AFTER SEASON
Wipe off moisture with piece of cloth, then wipe again with dry piece of cloth. Remove Blade, clean and lubricate
with cooking oil, the wrap in foil paper before storage. Remove all soiled oil from the Main Shaft and lubricate with
grease approved by FDA for the lubrication of food processing machinery. Do not use cooking oil. ALWAYS unplug the
machine when not in use.
SPECIFICATIONS*
Dimensions: 25-3/4” high x 11-1/8” wide x 15-1/8” deep
Weight: 61.7 lbs.
Shaving Capacity: 4.84 to 5.5 lbs. per minute
Motor: 115V, 200W
Power Requirement: 210W, 60Hz
Accessories: Spare Blade (1), Grease oil (1), Drain Hose (1)
*Specifications are subject to change without notice for further design and performance improvement.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
5
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
9. If ice block wobbles as it rotates, turn off power switch and re-center the ice block.
10. Remove the ice block.
BLADE ADJUSTMENT
1. The Blade isrecessed below the surface ofthe Shaving Disc when the Blade Adjustment Dial is turned to 0.
2. To raise the Blade, slowly turn the Blade Adjustment Knob counter-clockwise.
3. Set the Blade Adjustment Dial on 1for fine shaving and 6 for roughest shaving.
Note: THE DIAL WILL INDICATE 0WHENTHE BLADE ADJUSTMENT KNOB IS TURNED CLOCKWISE ALL THE WAY AND
STOPS PRODUCING ICE.
BLADE REPLACEMENT
1. Turn the Blade Adjustment Knob right all the way until it stops.
2. Unscrew the two Phillips-screws. Remove the Blade Holder and blade.
Important: DO NOT INTERFERE WITH THE CENTER SLOTTED SCREW.
3. Place the new Blade accurately on the Standard Level Guide Screws on the Blade Support.
4. Put the Phillips-screw in and slowly screw it on so the blade will not lift up from the Standard Level Guide Screws.
Screw it on tight.
*If both ends of the Blade are not accurately set on the Standard Level Guide Screws, the ice will not shave correctly.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
5
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
9. If ice block wobbles as it rotates, turn off power switch and re-center the ice block.
10. Remove the ice block.
BLADE ADJUSTMENT
1. The Blade isrecessed below the surface ofthe Shaving Disc when the Blade Adjustment Dial is turned to 0.
2. To raise the Blade, slowly turn the Blade Adjustment Knob counter-clockwise.
3. Set the Blade Adjustment Dial on 1for fine shaving and 6 for roughest shaving.
Note: THE DIAL WILL INDICATE 0WHENTHE BLADE ADJUSTMENT KNOB IS TURNED CLOCKWISE ALL THE WAY AND
STOPS PRODUCING ICE.
BLADE REPLACEMENT
1. Turn the Blade Adjustment Knob right all the way until it stops.
2. Unscrew the two Phillips-screws. Remove the Blade Holder and blade.
Important: DO NOT INTERFERE WITH THE CENTER SLOTTED SCREW.
3. Place the new Blade accurately on the Standard Level Guide Screws on the Blade Support.
4. Put the Phillips-screw in and slowly screw it on so the blade will not lift up from the Standard Level Guide Screws.
Screw it on tight.
*If both ends of the Blade are not accurately set on the Standard Level Guide Screws, the ice will not shave correctly.
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
6
BRAKE ADJUSTMENT-Adjust when ice is not shaving correctly.
1. Remove the rubber plug onthe front of the head cover.
2. Raise Ice Block Holder Crank Clockwise.
3. Take a straight edge screwdriver and turnBrake Adjustment Screw counterclockwise, slowly.
4. When the Ice Block Holder Crank drops, stop.
5. Turn Brake Adjustment Screw clockwise with screwdriver 2-2.5 full turns.
6. Test the pressure ofthe Crank. It should be firm to turn.
PROTECTOR
A Push Button Switch (Protector) is located on the left side of the Head Cover. If something is wrong with the blade
section or the revolving section, the machine will automatically stop to prevent overheating and damage the motor. In
such case, turn off the Power Source Switch (Disconnect the plug) and after the cause is removed. Plug incordand push
the protector. TheMotor will automatically start again.
TO MAINTAIN SANITATION WITHOUT TOOLS
For periodic cleaning of the Shaving Plate as well as adjacent area in the food zone, removal is possible as follows.
1. By removing the 4 thumbscrews located on the underside of the plate, the Shaving Plate can be easily removed
by pushing it up.
2. To clean the Shaving Plate Frame and the adjacent area, remove the 4 thumbscrews holding the Front Cover (2
thumbscrews on each side), then pull the Front Cover towards the user to remove. The entire food zone can be
easily cleaned.
3. Brake Shoe and worm gear should not have any grease on the metals. This is caused by Hot weather conditions
and heavy use of the shaver. Simple use a dry rag, turn the machine on, and wipe the parts clean.
STORAGE AFTER SEASON
Wipe off moisture with piece of cloth, then wipe again with dry piece of cloth. Remove Blade, clean and lubricate
with cooking oil, the wrap in foil paper before storage. Remove all soiled oil from the MainShaft and lubricate with
grease approved by FDA for the lubrication of food processing machinery. Do not use cooking oil. ALWAYS unplug the
machine when not in use.
SPECIFICATIONS*
Dimensions: 25-3/4” high x11-1/8” wide x 15-1/8” deep
Weight: 61.7 lbs.
Shaving Capacity: 4.84 to 5.5 lbs. per minute
Motor:115V, 200W
Power Requirement: 210W, 60Hz
Accessories: Spare Blade (1), Grease oil (1), Drain Hose (1)
*Specifications are subject to change without notice for further design and performance improvement.

www.SnoBiz.com 1(800)-742-8342 [email protected]
8
SWAN SI-100E OWNERS MANUAL 2020.1
Motor fails to turn
Main Sha does
not move up or
down
Does not shave
Ice block jumps out
or is unsteady
Shaved ice too fine
Shaved ice too rough
Texture of shaved
ice is not uniform
Turns heavily
Turns lightly
Cord
Ice Block
Holder
Crank
Blade
Blade
Brake
Ice
Block
Blade
Brake
Blade
Brake
Brake
Worm
Gear
Brake
Shoe
Brake
Brake
Brake
Shoe
Cord not properly
plugged in. Broken
power cord.
Missing or broken Lock
Pin for Ice Block
Holder Crank
Chipped or dull blade
Blade is raised too high
or uneven with Shaving
Plate.
Tension adjustment
of Brake too weak
Prongs not firmly
imbedded in ice block
Blade not set properly or
Blade is dull
Tension adjustment
of Brake too weak
Blade raised too
high because blade
does not shave
Tension adjustment
of brake too stong
Worn out Brake
Worm Gear
Weak or worn out
Brake Shoe Spring
Brake tension too ght
Brake tension too weak
Weak or worn out
Brake Shoe Spring
Plug cord into
socket properly.
Replace power cord.
Install new Lock Pin
Pin for Ice Block
Holder Crank
Replace blade
Set Blade flush
with Shaving Plate.
the outer side of the
Shaving Disc.
Replace blade
shave
Turn Brake Adjustment
Screw clockwise to ghten
Turn over ice block
so flat side is up
Set Blade properly or
sharpen Blade
Turn Brake Adjustment Screw
clockwise to ghten
Replace blade
high because blade
does not shave
Turn Brake Adjustment Screw
counterclockwise to ease
Replace Brake Worm Gear
Brake Worm Gear
Replace Brake Shoe Spring
Brake Shoe Spring
Ease tension by turning
Brake Adjustment Screw
counterclockwise
Tighten tension by turning
Brake Adjustment Screw
clockwise
Replace Brake Shoe Spring
PROBLEMS CAUSES SOLUTION
DOES NOT REVOLVE
DOES NOT SHAVE
ICE BLOCK
HOLDER CRANK
TROUBLE SHOOTING GUIDE

www.Snobiz.com 1(800)-742-8342 [email protected]
9
SWAN SI-100E OWNERS MANUAL 2020.1
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
8
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
FOR AUTHENTIC SWAN FACTORY PARTS
1 [phone]
Complete maintenance videos are available at:
SnoBiz YouTube

www.SnoBiz.com 1(800)-742-8342 [email protected]
10
SWAN SI-100E OWNERS MANUAL 2020.1
OWNERS MANUAL 2019.09
SwanIceShavers.com 1-888-353-3719
9
www.SwanIceShavers.com - 1-888-353-3719 [e-mail]
FOR AUTHENTIC SWAN FACTORY PARTS 1
[phone]
Complete maintenance videos are available
at:
Sno Biz YouTube