Swann ADW-300 User manual

1
www.swannsecurity.com SR233-ADW-10006-290709
Advanced Digital Wireless
Camera & Receiver
Operating Instructions
™
™
Advanced security made easy
ADW-300
SW233-ADW

222
FCC Verification:
NOTE: This equipment has been tested and found to comply with the limits for
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to cor-
rect the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna
· Increase the separation between the equipment and the receiver
· Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
· Consult the dealer or an experienced radio/TV technician for help
IMPORTANT NOTE: Prohibition against eavesdropping
Except for the operations of law enforcement officers conducted under lawful
authority, no person shall use, either directly or indirectly, a device operated pursu-
ant to the provisions of this Part for the purpose of overhearing or recording the
private conversations of others unless such use is authorized by all of the parties
engaging in the conversation.
WARNING: Modifications not approved by the party responsible for compliance
could void user’s authority to operate the equipment.
IMPORTANT SAFETY INSTRUCTIONS:
· Make sure product is fixed correctly and stable if fastened in place
· Do not operate if wires and terminals are exposed
2
Before You Begin

33
Table of Contents
Before You Begin 2
Table of Contents 3
Package Contents 4
Tips & Suggestions 4
Camera Layout 5
Receiver Layout 6
Menu Functions 7
Connecting to a TV/VCR 8-9
Software Installation 10-11
Opening the Software 12
Software Layout & Functions 13
Motion Sensor 14
Record 14
Storage 15
Video Capture 15
Photo Snapshot 16
Event List 16
Device Setup 17
Troubleshooting Guide 18
Technical Specifications 19
Help Desk 20
Warranty Information 20

444
Tips & Suggestions
Before doing a permanent installation, connect the camera to your TV or VCR
using this Quick Start Guide to ensure all components in the pack are working
correctly.
If you have trouble with connecting the product contact our Technical Support
team. Contact details are on the back cover page of this guide.
Install cameras high enough or out of reach to avoid tampering.
Place Security Stickers in a visible location to alert potential thieves they are being
monitored.
Place cameras in high traffic areas such as doorways to maximise security.
Use only the included Power Supply and do not modify or cut wires.
ADW-300 Camera with Stand
Receiver
A/V Cable
2 X Antennas
Power Adapters
Operating Instructions
Security Stickers
Mounting Hardware
Package Contents

5
Camera layout
Pairing button*
Antenna
connection
*Remove rubber cover to reveal pairing button
Pairing
LED
Power LED
Lens Infra Red
light
Front
Back

6666
Receiver Layout
34567
12
8910
1. CAMERA SELECT
When in display mode press to change between each
camera channel. Press to pair a camera with a channel once
you have selected the channel to pair. Press to reset the
receiver options when RESET is selected.
2. ZOOM IN / ZOOM OUT
Press to zoom in & zoom out in live view.
3. LEFT
Press to move the view left when in zoom mode. Press to
decrease a selection in the menu screen.
4. UP
Press to move the view up when in zoom mode. Press to
select previous selection above in the menu.
5. MENU
Press to access menu.
6. DOWN
Press to move the view down when in zoom mode. Press to
select next selection below in the menu.
7. RIGHT
Press to move the view right when in zoom mode. Press to
increase a selection in the menu screen.
8. Power Indicator LED
LED turns on when receiver is plugged to a power outlet.
9. PAIRING LED
LED turns on when a camera is paired.
10. SIGNAL LED
LED turns on when there is a signal from the camera to the
receiver.
USB socket AV Output Power socket
Antenna
connection

7
Menu Functions
After connecting the ADW-300 camera & receiver to your TV/VCR you will be able
to set up your camera/s to your receiver. To access the menu press the M button
on the receiver.
Audio vol
Use the LEFT & RIGHT arrow keys on the receiver to increase and decrease the
volume.
Scan time
This function allows you to change the display between single camera view and
quad view. You can also set the receiver to change between each camera display
in single camera view (must have atleast 2 cameras for this). Use the RIGHT & LEFT
arrow keys to scan between OFF (no scanning), 5, 10 & 15 second intervals.
Cameras 1-4
You can switch each channel ON & OFF. If the channel is set to OFF the display
will be completely black even when a camera is connected to that channel. Use
the RIGHT & LEFT arrow keys to switch between ON & OFF. When a channel is
switched OFF it will be skipped when scanning is activated.
Pair CAM 1 2 3 4
If you are unable to view a picture on your camera/s display your camera may not
be properly paired with a channel.
To pair a camera use the arrow keys to select between channel 1, 2, 3 & 4. Once
you have selected the channel you want to pair the camera with, press the CAM-
ERA SELECT button on the receiver.
You should now see a timer counting down on your TV. Using a pin or toothpick
press the PAIRING button on the back of the camera you want to pair with the
channel you have selected.
Note: you will have 60 seconds until the receiver stops searching for the camera’ss
signal.
Reset
To reset the settings above use the UP & DOWN button to scroll down to the RESET
option. Press the CAMERA SELECT button to reset the receiver options. Note: this
will not reset any camera that is paired to a channel.

888
Connecting to a TV/VCR
5A. Connect to VCR (Optional)
Connect the power
adapter plug into the power
socket attached to the
camera.
1
Connect the A/V cable
to the Input on the back
of the VCR
i
If your VCR is not already
connected to your TV,
connect another A/V cable
to the Output on the VCR
ii
From Receiver
To T V
Plug the camera’s
power adapter into
the wall socket.
2
Input
Output

9
INPUT
5B. Connecting to TV
Connect the the A/V cable to your
TV or VCR
5
From Receiver
From VCR
(Optional)
Connect the power adapter
plug into the receiver’s
power socket.
3
Connect the A/V Cable
to a TV Input
i
Connect the
power
adapter into
the wall
socket.
4

101010
Software Installation
1. Insert the software CD. If the CD does not automatically start click START> MY
COMPUTER and click on the drive your software CD is in, to open it.
Find the file named AUTORUN.EXE and double click it.
2. Select the language you would like
to use for the installation process.
3. Click NEXT.
4. Click the “I accept the agreement”
selection button then click NEXT.
5. Click NEXT or choose your pre-
ferred location for the program.
< Back Next > Cancel
< Back Next > Cancel
Next > Cancel
I accept the agreement
I do not accept the agreement