Swann CoreCam Pro User manual

1
EN
CoreCam Pro Spotlight Camera
Cámara con Foco CoreCam Pro
Caméra de Projecteur CoreCam Pro
Telecamera con illuminazione CoreCam Pro
CoreCam Pro Scheinwerfer Kamera
EN Quick Start Guide ES Guía de inicio rápido FR Guide de démarrage rapide
IT Guida rapida DE Schnellstartanleitung
Model: SWIFI-COREPRO

2
EN
CAMERA OVERVIEW
Threaded screw hole
(attaches to the included wall-mount bracket)
Pull rubber cap gently from the bottom to access:
• ON/OFF switch
• MicroSD card slot
32GB card pre-installed, Max. 128GB card supported
• Micro USB charging port
• Reset button
— Press and hold for 5 seconds to enter pairing mode
— Press and hold for 10 seconds to factory reset the camera
Microphone Speaker
QR code (for
device pairing)
Rubber cap
Passive infrared
motion sensor
LED indicator
Night detection
sensor
Infrared LEDs
(for night vision) Spotlight
Threaded
mounting post
Bracket screw hole (x3)
Locking knob

3
EN
GETTING STARTED
Before using the camera for the first time, fully charge it with the included micro USB charging cable.
1Pull open the rubber cap on the bottom of the camera.
2Slide the ON/OFF switch to the ON position Note: You can also charge the camera with the
switch OFF but you won’t be able to check the LED indicator for the charging status.
3Insert the smaller end of the micro USB charging cable into the micro USB port on the camera.
4Insert the other end of the micro USB charging cable into a USB wall charger such as the USB
power adapter for your smartphone.
5The LED indicator on the front of the camera will turn solid blue indicating that the camera is
charging. When the camera is fully charged, the LED indicator will turn off. Actual charging times
may vary depending on the USB power supply (DC5V 2.1A is recommended for faster charging)
and the remaining battery level. A full charge may take up to 6 hours.
6 After charging is finished, unplug the micro USB charging cable from the camera and make sure
to close the rubber cap tightly to keep out water and dust.
The camera comes with a 32GB microSD card pre-installed for recording events and performing
firmware updates. You can easily replace the microSD card with a new one (max. 128GB card
supported), if needed in the future. Simply open the rubber cap on the bottom of the camera, eject
the current microSD card (push in until it clicks) from the microSD card slot, and then insert the new
microSD card (with the label side facing the front of the camera) into the slot until it clicks into place.
You should format the microSD card the first time it is used. From the Swann Security app, go to
Device Settings > [your camera] > Advanced Settings and tap Format.
Charging the camera
Replacing the microSD card

4
EN
GET THE SWANN SECURITY APP
1Download the latest version of the Swann Security app from the Apple App Store® or Google
Play™ Store on your iOS or Android device. Simply search for "Swann Security".
2Open the app and create your Swann Security account by tapping “Not yet registered? Sign Up” at
the bottom of the screen. Then, activate your Swann Security account by confirming the verification
email that is sent to the registered email address.

5
EN
Launch the Swann Security app and sign in. Tap the Pair Device button on the screen (or tap the menu
icon in the top left and select “Pair Device”). The app will now guide you through the pairing process
to set up the camera with your Wi-Fi network.
Before you begin, have the camera with you and be close to your router. Please note that the camera
is only compatible with the 2.4GHz network. If your router is using the 5GHz band, please ensure it is
operating in mixed mode.
SET UP THE CORECAM

6
EN
The camera can be conveniently placed on a table or shelf, or mounted on a flat surface using the
included bracket. Because the camera is completely wire-free, you’ll have a lot of flexibility on where you
can install it. Choose a location with strong, reliable Wi-Fi reception to ensure best video streaming and
battery performance. The easiest way to check is to use your smartphone. Connect your smartphone to
your Wi-Fi network at the spot you have chosen and see if you get 2 bars of Wi-Fi signal or more. As a
general rule, the nearer the camera is to your router, the better the wireless connection quality. If you’re
finding the wireless signal is too weak or out of range, consider installing a Wi-Fi range extender.
CAMERA PLACEMENT
Mounting the bracket
If mounting to a wooden surface, screw
bracket directly to the surface.
If mounting to a masonry surface (brick,
concrete), mark and drill holes, insert wall
plugs, and screw bracket to the surface.
Attaching the camera to the bracket
Screw the threaded hole at the bottom of the
camera onto the threaded post of the bracket
by turning the locking knob clockwise until the
camera is securely attached.
After installation, make sure to
remove the protective plastic film
covering the camera lens.
Adjusting the viewing angle
Loosen the adjustment ring slightly by
turning counter-clockwise. Swivel or tilt
the camera as needed then tighten the
adjustment ring to lock the position.

7
EN
Download the Swann Security app manual for Android/iOS via the App Menu > User Manual to
learn more about using the Swann Security app to view camera live video, use 2-way talk, playback and
download motion recordings, check battery level, configure various camera settings including spotlight
duration, motion detection sensitivity, modes, and more.
Screens may vary slightly depending on the Swann Security app version (Android version shown above)
THE SWANN SECURITY APP MANUAL

8
EN
MOTION DETECTION TIPS
Optimizing motion detection
• The camera’s passive infrared motion sensor
detects heat signatures of moving objects.
• You’ll generally get good detection results
by pointing the camera at an angle where
people will be moving across the coverage
area (i.e., from left to right or right to left, see
figure on the right) as the motion sensor is
less sensitive to movement of people walking
towards it.
• Avoid aiming the camera at areas surrounded by large trees and bushes that sway a lot in the
wind. This may cause false alerts during extreme weather conditions.
• The motion sensor sensitivity can be adjusted using the camera’s Detection Settings menu in
the app. As every home environment is unique, we recommend experimenting with the motion
sensor sensitivity settings to find out which works best for yours. Note that the higher the
motion sensitivity, the faster the camera’s battery will drain as more power will be required to
detect motion farther away.
• During night time when motion is detected, the camera’s built-in spotlight will automatically turn
on. You can configure how long the spotlight will stay on once a motion event is detected using
the camera’s Detection Settings menu in the app. You can choose from 30 seconds to up to 300
seconds. The spotlight can also be turned on manually using the Light icon on the camera’s live
view screen.
Less
sensitive
More
sensitive

9
EN
HELP AND RESOURCES
Have questions?
We’re here to help! Visit the Swann Help Center at support.swann.com.You can obtain dedicated
technical support for your product, find troubleshooting articles, participate in the community
forums, and more. You can also email us at any time for information and advice at: [e-mail]
LED indicator guide
The LED light on the front of your camera helps inform you of what is happening with the device.
Rebooting the camera
On rare occasions, it might be necessary to reboot your camera if it becomes unresponsive. A simple
reboot can also fix connectivity issues quickly. To reboot the camera, open the rubber cap on the
bottom of the camera, slide the ON/OFF switch to the OFF position, wait for 60 seconds, then slide the
ON/OFF switch back to the ON position.
Solid Blue USB charging
Solid Red Live streaming / Motion recording
Slow Blinking Blue Wi-Fi Pairing mode
Fast Blinking Blue Connecting to Wi-Fi
Infrared LEDs Blinking Firmware update in progress

10
ES
DESCRIPCIÓN GENERAL DE LA CÁMARA
Orificio de tornillo roscado
(para soporte de montaje de cámara)
Tire suavemente de la tapa de goma desde la parte inferior para acceder a lo siguiente:
• Interruptor ON (ENCENDER)/OFF (APAGAR)
• Ranura de la tarjeta microSD
tarjeta preinstalada de 32 GB, tarjeta compatible de 128 GB máx.
• Puerto de carga micro USB
• Botón de reinicio
— Mantenga presionado durante 5 segundos para entrar en el modo de vinculación
— Mantenga presionado durante 10 segundos para reestablecer los valores de
fábrica de la cámara.
Micrófono Altavoz
Código QR (para
emparejar el
dispositivo)
Tapa de goma
Sensor infrarrojo
pasivo de movimiento
Indicador LED
Sensor de detección
nocturna
Luces LED infrarrojas
(para visión nocturna)
Poste de
montaje roscado
Perilla de bloqueo
Agujero del tornillo del soporte (x3)
Foco