SWASTIK DTC-9621-1 User manual

Instruction Manual of Humidity Controller
Thank you for using Swastik Humidity Controller.
This instruction describes product function, features and
proper usage.
Content Index
S1
!!
Warning
Note
1. For heat radiation, leave space around the instrument and do
not jam the ventilation holes in the instrument
2. Keep enough space between the instrument and equipment
which generates high frequency and surge.
3. Connect wires correctly
4. Use the instrument under rated load and power supply.
5. Use standard grade of alcohol to clean the instrument; don't use
paint thinner or similar chemicals
6. Read and understand this instruction carefully before use
7. Don't use the instrument in case the front panel peels of breaks.
1. To avoid electric shock, DON’T touch the AC power supply
terminals after power on.
2. Before power on, please confirm voltage conformity in range of
AC 210~240V, to avoid damage to instrument.
3. Never remove, retrofit or repair the product or contact any
internal components.
4. Tighten screw with 0.74-0.90Nm torque, as loose screws may
cause fire.
5. Use appropriate fuse to ensure power supply line and
input / output line to prevent current impact.
6. Don't use the instrument in occasion of flammable,
explosive gas, discharge of steam.
Warning
Note
S1
Features
S2
S2 Features
Technical specification
Parameter Setting
S3
S4
LED Indication
Set Key
When Instrument Power On, Press key Display message as below
Shift Key UpKey Ent key
Upper Display window
Lowe Display window
S3 Panel instruction
Panel instruction
S4 Parameter Setting
S5
S6
Parameter Description
Wiring diagram
Indicational / Controlling of Humidity
Programmable resolution setting for
Easy to operate
Build in Relay contacts
High Accuracy of
Excellent quality, safety and strong resistance to interference
Humidity
Humidity
DTC-9621-1
SET
Humidity Controller
ENT
Swastik
SET
O/P1
°c
%
O/P2
888.8
888.8
Automation & Control
Model No: DTC-9621-1
Input specification of Sensor :
Measuring range of Sensor :
Measuring accuracy :
Adjustment method :
Control Action :
Relay contact :
Size of instrument :
Panel cutout :
Rh Sensor
0 - 100 % Rh
0.5 % of FSD (± 1°C)
Features Touch key pad
Humidity
230 vac/5Amp
96x96x90 mm
92x92x90 mm
+
50
2
0025
SETH
HY-H
PASS
SET
Press key
SET
Press key 3 Sec.
SET
Press key
Use & key to set value for the Humidity
Use & key to Hysteresis value (Humidity)
Use & key to set Password
Technical Specification
000
H-OF
Use & key
HY
0020
0400
0100
0004
PID
Mode
KPH
KIH
KDH
CTH
Mode
Control Mode Humidity
If select PID Mode
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
Use & key
Use & key
Use & key
(Use & key)
Use & key
Heat Cool
H-AC H-AC
0000
H-DL
SET
Press key
Use & key to select
(RH / DRH)
Humidity Action
(HY / PID)
ENT
Press key to save & exit from any parameter
(Humidity Offset)
Note: Press key 3 Second for PID tunning

S5 S6
Display
Message Description Selection
H-dl
H-OF
SETH
HY-H
PASS
H-AC
Set Value for the Hysteresis
Hysteresis value - Humidity
Set Password
Humidity compressor off
time interval (delay time)
Humidity Action (increase or
decrease relative humidity)
20 (000 or 00.0)
2 (1 to 9)
25
Heat / Cool
0000 (0-999) minutes
-30.0 to 30.0°C
RH offset
TEMP. RANGE:
RH RANGE:
0-400°C PID ON/OFF
100% PID ON/OFF
18 19
11 12 13 14 15 16 17 20
30
I/PGND
PT-100
TEMP RH
+5V
RED
GREENBLACK
Parameter Description Connection Diagram
TEMP. SENSOR: RTD
MODEL NO.: DTC-9621-1
RH SENSOR: 3.3V DC
L
~
N
89 12
3
4
5
6
7
10
!!
HEATER RH 230V AC
NO NONC NCC C
KPH
KIH
KDH
CTH
Mode
Proportional parameter for
Humidity
Integral parameter for
Humidity
Cycle timer for Humidity
Derivative parameter for
Humidity
Method is Hysteresis or Propo-
rtional Mode to control Humidity On-off (Hy) / PID
20
400
100
2 (2-60) seconds