Swisher LS722X User manual

Read and follow all Safety
Precautions and Instructions
before operating this
equipment.
LOG
SPLITTER
OWNER’S
MANUAL
1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093 PHONE [phone]
FAX [phone]
MODEL NO.
LS722X
STARTING SERIAL #:
L206-010001
Manufacturing quality lawn care equipment since 1945
Safety
Assembly
Operation
Service and Adjustment
Repair Parts
Made In The
USA
IMPORTANT
swisherinc.com
11624
Rev. 06-010

2
In the event you have a claim under this warranty, you must return the product to an authorized service dealer.
All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or
repair under this warranty shall be borne by the purchaser. Should you have any questions concerning this
warranty, please contact us toll-free at 1-800-222-8183. The model number, serial number, date of purchase,
and the name of the authorized Swisher dealer from whom you purchased the splitter will be needed before any
warranty claim can be processed.
THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS
STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of
consequential damages or limitations on how long an implied warranty may last, so the above limitations or
exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights,
which vary from state-to-state. This is a limited warranty as defined by the Magnuson-Moss Act of 1975.
LIMITED WARRANTY
The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in
materials and workmanship for a period of ONE (1) year from the date of purchase by the original consumer
purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or
workmanship. This warranty is subject to the following limitations and exclusions:
TABLE OF CONTENTS
WARRANTY………………....….2
SAFETY PERCAUTIONS………3-4
TOWING..….……..……………..5
OPERATION……………………5-8
MAINTENANCE.…………………….7-8
DECALS…..………….……………….9
PARTS BREAKDOWN………………10-13
SPECIFICATIONS..…………………..15
1) Engine Warranty All engines utilized on our products have a separate warranty extended
to them by the individual engine manufacturer. Any engine service
difficulty is the responsibility of the engine manufacturer and in no
way is Swisher Mower Co., Inc. or its agents responsible for the engine
warranty. The Briggs & Stratton Engine Service Hot-Line is 1-800-
233-3723.
2) Commercial Use The warranty period for any product used for commercial or rental is
limited to ninety (90) days from the date of original purchase.
3) Limitation This warranty applies only to products which have been properly
assembled, adjusted, and operated in accordance with the instructions
contained within this manual. This warranty does not apply to any
product of Swisher Mower Co., Inc., that has been subject to alteration,
misuse, abuse, improper assembly or installation, shipping damage, or
to normal wear of product.
4) Exclusions Excluded from this warranty are normal wear, normal adjustments, and
normal maintenance. The pump, valve, and cylinder each carry separate
manufacture’s warranties. The valve and cylinder both carry a one (1) year
limited warranty. The pump carries a two (2) year limited warranty.

SAFETY PRECAUTIONS
WARNING: The engine exhaust from this product contains chemicals known to the state of California
to cause cancer, birth defects or other reproductive harm.
DANGER: Your log splitter was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can result
in serious injury. If you violate any of these rules, you may cause serious injury to yourself or others.
• Read and understand the manual. Learn to operate this equipment in a safe manner. Familiarize
yourself with all of the controls in a safe environment before starting to work with this machine.
• DO NOT under any circumstances alter this log splitter. This equipment was designed and
engineered in accordance with operating instructions. Altering this equipment, or using this
equipment in such a way as to circumvent its design capabilities and capacities, could result in
serious injury or fatality and WILL VOID THE WARRANTY.
• Allow ONLY responsible adults who have read this manual to operate this machine. NEVER
allow children to operate this machine.
• NEVER operate or allow someone to operate this equipment while under the influence of
alcohol, drugs or medication. Being coherent is essential for safety.
• ALWAYS use outdoors with adequate ventilation. DON’T run the engine in an enclosed area.
Exhaust gases contain carbon monoxide. This odorless gas can be deadly when inhaled.
• NEVER use splitter for any other purpose than splitting wood. Any other use can result in
injury. Your splitter is a precision piece of power equipment, not a toy. Therefore, exercise
extreme caution at all times.
• ONLY a single operator is to load and operate the log splitter. KEEP all others, including pets
and children, a minimum of 20 feet away from your work area. More accidents occur when
more than one person operates the log splitter than any other time.
• ALWAYS wear protective gear such as safety goggles, protective hearing device, steel-toed
shoes, and tight-fitting gloves without drawstrings or loose cuffs.
• NEVER wear loose clothing or jewelry that can be caught by moving parts of the splitter and
pull you into it. Keep hair away from moving parts.
• NEVER operate your splitter on wet, muddy, or icy surfaces. KEEP work area clean of split
wood. Safe footing is essential in preventing accidents.
• ONLY operate splitter on level ground with wheels blocked, not on the side of a hill. It could
tip, or rolling logs, poor footing, etc. could cause an accident.
This Safety Alert Symbol indicates important messages in this manual.
When you see this symbol, carefully read the message that follows and be
alert to the possibility of personal injury.
Read this manual completely. This machine can amputate hands, feet, and throw objects.
Failure to observe the following safety instructions could result in serious injury or death.
3

•
NEVER operate your splitter near a flame or spark. Hydraulic oil and gasoline are flammable and can
explode.
• NEVER fill gas tank while the engine is hot or running. Allow the engine to cool before refueling.
• This unit is equipped with an internal combustion engine and should not be used on or near any
unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is
equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used it
should be maintained in effective working order by the operator.
-NOTE-
In the state of California, the above is required by law (Section 442 of the California Public Resources Code).
Other states may have similar laws. Federal laws apply on federal lands. A spark arrester muffler (optional by
manufacturer) is available at your nearest engine dealer. Check legal requirements in your area.
• ONLY use your hands to operate the control lever. NEVER use foot, knee, rope or any extension device.
• Split ONLY one log at a time. NEVER attempt to split two logs on top of each other.
• NEVER place hands or feet between log and splitting wedge or between log and ram during forward or
reverse stroke. ALWAYS keep fingers clear of splits that open in log during splitting operation.
• DO NOT straddle or reach across the splitting area while operating the splitter.
• DO NOT step over splitter when the engine is running. You may trip or accidentally activate the splitting
wedge. Walk around to get to the other side.
• NEVER attempt to load splitter while splitting wedge is in motion. When loading log splitter, place hands
on the sides of the log, not the ends.
• NEVER attempt to split woods across the grain. Wood may burst or fly out of your splitter and result in
serious injury.
• NEVER leave your splitter unattended with the engine running. Shut off the engine if you are leaving
your splitter, even for a short period of time. Someone could accidentally activate the ram and be injured.
• Both ends of the log should be cut as squarely as possible to prevent the log from sliding out of the splitter
during operation. Log length should be kept to 24” or less.
• NEVER operate your splitter while it is attached to the tow vehicle.
• BEFORE towing, be certain that the splitter is securely attached to the towing vehicle and that the support
leg, beam and cylinder are secured in there respective towing positions.
• NEVER allow persons to ride on splitter. DO NOT carry any cargo or wood on your splitter. It may fall
off and cause an accident.
• DO NOT loosen or remove any hydraulic fitting, line or reservoir cap while your splitter or engine is
running.
• Fluid escaping from a very small hole can almost be invisible. DO NOT check for leaks with your hand.
See maintenance section for instructions. IF injured by escaping fluid, see a doctor at once. Serious
infection or reaction can develop if proper medical treatment is not administered immediately.
• DO NOT operate your splitter in poor mechanical condition or when it is need of repair.
• ALWAYS disconnect the spark plug wire and place the wire where it cannot contact the spark plug, to
prevent accidental starting the engine when setting up, transporting, adjusting or repairing.
4

ASSEMBLY
This log splitter has been partially assembled at the factory. Refer to the drawings and part lists should it become
necessary to disassemble the unit for repair or replacement of parts.
Inspect all components for damage. If you believe you have a damaged part please contact customer service
immediately at 1-800-222-8183.
WARNING: Exercise extreme caution, as parts are very heavy. Sufficient persons or mechanical handling
equipment should be used.
Refer to uncrating and assembly instructions for assembly procedures.
OPERATION
INTENDED USE: This log splitter is intended and designed to only split wood. NEVER use for any other
purposes. Doing so can cause injury or VOID THE WARRANTY.
IMPORTANT: This unit is shipped with oil but without gasoline in the engine. After assembly, see separate
Engine Manual for proper fuel and oil recommendations.
WARNING: DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE
AND HYDRAULIC RESERVOIR.
FILLING THE HYDRAULIC RESERVOIR
Fill the hydraulic reservoir with at least 12 Quarts of Dextron III Automatic Transmission fluid or 10W AW
hydraulic fluid. After the hydraulic reservoir and the engine crankcase are filled correctly with their respective
oils, start the engine. Remember to set the throttle and turn on the fuel shut-off valve. The hydraulic pump
should prime itself. With the engine running, move the hydraulic valve lever toward the wedge. This will cause
the cylinder to extend and expel air. When the cylinder is fully extended, retrac
t it. Repeat this procedure several
times. (An erratic movement of the cylinder indicates that there is air in the system). Once the cylinder has a
smooth and constant speed indicating that all air has been expelled, add another 4 quarts of oil, this should then
bring the fluid level up to approximately 3” below the fill hole. This model requires approx. 16-17 Quarts of
hydraulic fluid.
NOTE: If the tank is overfilled, it will tend to expel oil from the breather cap when the cylinder is retracted.
START UP
WARNING:
DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE
AND HYDRAULIC RESERVOIR.
See separate Engine Manual for fuel and oil recommendations. If applicable your log splitter has come equipped
with a fuel shut-off valve for towing purposes.
Before starting engine make sure crankcase is filled correctly with oil and the proper fuel has been used. The
engine will only start when the throttle lever and fuel shut-off valve if applicable are turned to their ON positions.
STARTING INSTRUCTIONS
Briggs & Stratton 7HP Engine
1. Move throttle control to “FAST.”
2. Push primer bulb three (3) times. NOTE: Do not use primer to restart a warm engine after a short
shutdown.
3. Grasp rope handle and pull out slowly until resistance it felt. Then pull rapidly with a full arm stroke.
NOTE: If engine fails to start after three (3) pulls, repeat steps 1 and 2.
4. When Engine starts, leave throttle control at “FAST.” The throttle must be set in the fast position for
maximum performance.
5. To stop engine, move throttle lever to “SLOW” for a few seconds then to “STOP.”
5

POSITIONING THE CYLINDER
1. Remove lock pins from the cylinder retention clips and rotate clips down exposing the open slots on the
cylinder retention bracket (reference Figure 2).
2. Slide the Cylinder forward until the rear trunnions clear the slots then lift the back side of the cylinder until
the rear trunnions clear the cylinder retention bracket and slide cylinder back until the front cylinder
trunnions slide into the open slots of the cylinder retention bracket (reference arrow in Figure 2).
3. Rotate the cylinder retention clips upward around the cylinder trunnions and lock them in place using the
lock pins.
4. Next you need to remove the lock pin from the beam pivot bracket and rotate the beam counter clockwise
90 degrees until the pivot holes are in alignment and reinstall ball lock pin (reference Figure 4). Your
splitter is now in the horizontal operating position.
5. Remove the hitch pin from the beam pivot (reference Figure 4). Pivot your beam into the vertical position
and reinstall the hitch pin in the center hole (reference Figure 5). Your splitter is now in the vertical
operating position.
Figure 2Figure 1
Figure 3
Figure 4 Figure 5
6

WARNING: NEVER OPERATE THE SPLITTER WITH THE CYLINDER IN THE STORED
POSITION.
SPLITTER OPERATION
1. Set up the log splitter in a clear, level area and block the wheels. The suction port on the tank should
always be on the lower side of the log splitter.
2. Place a log on the beam, against the foot plate. Make sure the log is securely on the foot plate and up
against the beam.
3. Depress the valve lever so that the cylinder will drive the push block into the log. Extend the cylinder
until the log splits or to the end of its stroke. If the log has not completely split after the cylinder has
reached the end of its extension, retract the cylinder. NOTE: Leaving the valve in the “actuate” position
at the end of the stroke may damage the pump. Always use extra care when splitting logs with ends that
are not square.
NOTE: To extend the life of the hydraulic cylinder, avoid “BOTTOMING OUT” the cylinder.
TOWING SAFETY
This unit should not be towed on any street, highway, or public road without checking the existing federal, local,
and state laws. Any licensing or modifications such as taillights, etc., need to comply with existing federal, local,
or state vehicle requirements is the sole responsibility of the purchaser. Obey all regulations when towing on
public roads and highways. See also
SAFETY PERCAUTIONS.
WARNING: NEVER TOW THE SPLITTER WITH CYLINDER IN THE OPERATING POSITION.
Turn the fuel shut-off valve if applicable OFF to prevent flooding of the engine while traveling.
Be careful when backing up. You can easily jack-knife your splitter.
TOWING AT NIGHT
The requirements for taillights are based on States regulations. Some states allow towing at night as
long as the towed equipment does not visibly impair the tow vehicle taillights. This is bas
ed on a state,
to state requirements. The customer is responsible for meeting the states requirements.
If a “Statement of Origin” is required in your state, see your local dealer to receive one.
HYDRAULIC SAFETY
The hydraulic system on your splitter requires careful inspection along with the mechanical parts. Be sure to
replace any frayed, kinked, cracked or otherwise damaged hydraulic components. Just because it isn’t leaking
today doesn’t mean that it will not fail tomorrow.
Fluid escaping from a very small hole can almost be invisible. Do not check for leaks with your hand. Escaping
fluid under pressure can have sufficient force to penetrate skin causing serious personal injury or even death.
Leaks can be detected by passing a piece of cardboard or wood over the suspected leak and looking for
discoloration.
IF injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if
proper medical treatment is not administered immediately.
Should it become necessary to loosen or remove any hydraulic fittings, lines or reservoir cap, be sure to relieve all
pressure by shutting of the engine and moving the control handle back and forth several times.
NEVER remove the cap from the hydraulic tank or reservoir while the unit is r
unning. Hot oil under pressure
could result in serious injury. See also
SAFETY PERCAUTIONS.
The pressure relief valve on your splitter is preset at the factory. DO NOT adjust the valve. Only a qualified
technician should perform this adjustment.
7

MAINTENANCE AND STORAGE
WARNING:
DISCONNECT THE SPARK PLUG BEFORE PERFORMING ANY MAINTENANCE.
Consult the operating and maintenance instructions of the engine manufacturer for engine care.
Always check the oil level of the hydraulic reservoir before operation. Operating without an adequate oil
supply will cause severe damage to the pump.
Periodically check that all nuts, bolts, screws, clamps and fittings are tight and secure.
To keep your splitter in top working condition perform all recommended maintenance procedures before you use
your splitter.
If the wedge becomes dull or nicked a grinder or sharpening tool can be used to sharpen it.
Completely drain the fuel tank prior to storage. Always store gasoline in an approved, tightly sealed container. Store
container in a dry, cool place with adequate ventilation. Keep fuel away from areas where fumes could contact open
flame, pilot light or sparks.
Be aware of the environment when disposing of used petroleum products. Please dispose of used hydraulic
fluid, engine oil and any by products from the maintenance of your splitter at approved recycling centers.
Should it become necessary to disassemble the unit for repair or replacement of parts, refer to the drawings and parts
list on the following pages. Exercise extreme caution, as some parts are very heavy and will require sufficient
persons or mechanical handling equipment.
Your Swisher Log Splitter has been produced with components designed specifically to this machine. Although
standard springs, hardware and ect may look similar to parts used on other machinery, they may in some cases
be made of a different construction and/or materials. All replacement parts must meet manufacturer’s
specifications.
8
The operation of any splitter can produce foreign objects to be thrown into the
eyes, resulting in severe eye damage. Always wear certified safety glasses or
wide-vision safety goggles over spectacles before staring any splitting machine
and while operating such a machine.
The operation of any splitter produces sound waves that are damaging to the
human ear. Ear protection is recommended.

9
OD12 – HYDRAULIC FILL PLUG
DECAL
11427 – LS DANGER DECAL
OD33– SPEED DECAL
OD16 – FUEL SHUT OFF DECAL
(NOT ALL MODELS)
OD07 – COLD WEATHER DECAL
SAFETY DECALS
Replace decals immediately if damaged.
11794 – CAUTION DECAL

10
ASSEMBLY DETAIL
LS722X MODELS

11
SERVICE PARTS
Please have Model and Serial Numbers ready when ordering parts.
Color cannot be guaranteed upon service parts.
ITEM NUMBER DESCRIPTION PART NUMBER
1 54" Return Hose 7290
2 48" Pressure Hose 7289
3 #12 Hose Clamp LS5001
4 Return Line Fitting 7329
5 Filter Head LS1112
6 Filter Element LS1113
7 3/4" NPT Filler Cap w/Hole 7379
8 Hydraulic Reservoir/Tank 11467TK
9 Bolt 3/8-16 X 3/4 Serr Flange NB780
10 Nut 3/8-16 Serr Flange NB779
11 Bolt 5/16-18 X 3/4 Serr Flange NB596
12 Nut 5/16-18 Serr Flange NB170
13 #16 Hose Clamp LS4999
14 20" Suction Hose 7346
15 Hydraulic Pump-LS722X LS2001H
16 Pressure Line Fitting 11248
17 Motor Base Weldment 11207TK
18 Tongue Support Weldment 11373TK
19 3/8 X 2 1/2 Safety Hitch Pin H11
20 Bolt 3/8-16 X 2 1/2 GR 5 NB619
21 Washer 3/8 SAE NB272
22 Nut 3/8-16 Nyloc NB182
23 Tongue Weldment 11374TK
24A Leg Support Bracket 1 11372TK
24B Leg Support Bracket 2 11425TK
25 Leg Weldment 11371TK
26 5/16-18 Special Hex Flange Shoulder Bolt NB743
27 Additional Support Weldment 11615TK
28 Washer 5/16 SAE NB275
29 Nut 5/16-18 Nyloc NB181
30 5/16 X 1 Ball Lok Pin - Ring Grip 11619
30A Plastic Lanyard NB652
30B Bolt 1/4-20 X 1/2 MSC ZP NB114
30C Nut 1/4-20 Serrated Flange NB524
31 Bolt 3/8-16 X 1 1/2 GR 5 NB107
32 1/8 X 1/2 #3 Woodruff Key 024002
33 Pump Pulley 7306
34 5/16-18 X 1/2 Set Screw w/Loctite NB312
35 37" Belt 11399
36 Idler Bushing 6037
37 Idler Arm 6041TK
38 Idler Spacer 6040
39 Idler Pulley B527
40 Nut 3/8-16 2-Way Lock NB280
41 Clutch Lever 11226TK
42 Handle Grip 2077
43 Clutch Spring 682S
44 Bolt 3/8-16 X 5 Turned Eye 11223
45 Tension Strap 11376TK
46 Axle Weldment 11370TK
47 Tire & Wheel F4157WF
48 Washer 3/4ID X 1 1/4OD 10GA NB184
49 Cotter Pin 1/8" X 1" NB126

12
ITEM NUMBER DESCRIPTION PART NUMBER
1 Beam W eldment 11468TK
2 Wedge W eldment 11910TK
3 Wedge GIB Angle 11857TK
4 Bolt 3/8-16 X 1 1/4 Carriage 10501
5 Nut 3/8-16 Nyloc NB182
6 Nut 1/2-13 Nyloc Jam NB121
7 1/2-13 X 3 1/2 GR5 ZP NB577
8 Ram Cylinder 11242TK
9 2-Way Pipe Nipple 7292
10 Hydraulic Fitting 7291
11 Stationary Line Assembly 7288TK
12 Valve Inlet Fitting 7387
13 Valve Control 7287TK
14 Return Line Fitting 7329
15 Master Chain Link 7424
16 Valve Control Handle 7423
17 Handle Grip 7425
18 1/4 X 1 Clevis Pin NB522
19 Cotter Pin NB597
20 Cylinder Retention Plate 11393TK
21 3/8" X 1 3/8" Hitch Pin NB632
22 Bolt 5/16-18 X 1 1/4 HCC GR5 NB504
23 W asher 5/16" SAE NB275
24 Latch Pin Bushing 7839Z
25 Washer 17/32 X 1 1/4 X 16GA NB217
26 Nut 5/16-18 Nyloc Nut NB181
BEAM DETAIL

13
PIVOT DETAIL
ITEM # DESCRIPTION PART #
1 Beam Pivot Weldment 11469TK
2 Bolt 3/4-10 X 2 GR8 11431
3 Washer Belleville 1.50 OD X .761 ID X .098 X .134 AS155
4 Washer 3/4 SAE NB146
5 Nut 3/4-10 Nyloc NB609
6 Bolt 1/2-13 X 4 GR5 NB132
7 Nut 1/2-13 Nyloc NB281
8 1/2 X 3 1/2 HITCH PIN W/ HAIR PIN NB648
9 3/8 X 1 5/8 Ball Lok Pin 11397
10 Plastic Lanyard NB652
11 1/4-20 X 3/4 Serrated Flange Bolt GR5 NB690
ENGINE DETAIL
ITEM # DESCRIPTION PART #
1 Engine N/A
2 Bolt 5/16-18 X 2 1/4 Serr. Flange NB622
3 Bolt 5/16-18 X 1 1/4 Serr. Flange NB253
4 Nut 5/16-18 Serr. Flange NB170
5 3/16 X 1 Keystock 9030
6 5/16-18 X 1/2 Set Screw w/Loctite NB312
7 Engine Pulley 7/8" ID 7323
8 Washer Belleville 699
9 Bolt 3/8-24 X 1 w/Loctite NB238N
NOTSHOWN Fuel Shut Off Valve (Inline) 7414
NOTSHOWN Fuel Line Clamp 6FLC
3
2
1
4
4
5
9
6
87
Hydraulic Hoses Not Shown for Clarity

14
NOTES :
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________

15
Models
LS722X
Splitting
Force
22 Tons
Engine
7 HP Briggs and
Stratton Intek
Splitting
Positions
Horizontal/Vertical
Cylinder
Size
4" X 24"
Pump
2 Stage with Heavy
Duty Bearings
Pump
Specs
11 Gallons Per
Minute
Valve
Auto Return
Drive
System
Belt Drive with
Clutch for Easy
Starting
Hydraulic
Fluid
Capacity
16-17 Quarts
Maximum
Log length
25"
Tire Specs
13.00 X 5.00
Metal
Fenders
No
Ball Hitch
No
Unit
Weight
410 Lbs
SPECIFICATIONS

16
OWNER’S
MANUAL
MODEL NO.
LS722X
HOW TO ORDER
REPAIR PARTS:
LOG SPLITTER
Each Log Splitter has its own serial number. Each engine has
its own serial number. The serial number for the Log Splitter
will be found on the right hand side of the hydraulic oil
reservoir. The serial number for the engine will be found on
the top of the blower fan housing.
All Log Splitter parts listed herein may be ordered directly
from Swisher Mower & Machine Co. Inc., your nearest
Swisher dealer, or from our website.
All engine parts may be ordered from the nearest dealer of the
engine supplied with your log splitter
. Parts subject to change
without notice.
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INFORMATION AVAILABLE:
* PRODUCT – SWISHER LOG SPLITTER
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
* ENGINE MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER
* PART DESCRIPTION
www.swisherinc.com
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER MOWER & MACHINE CO. INC.
1602 CORPORATE DRIVE
WARRENSBURG, MO 64093
SWISHER MOWER & MACHINE CO. INC.