Swisher LS67522HP User manual

Read and follow all Safety
Precautions and Instructions
before operating this
equipment.
LOG
SPLITTER
OWNER’S
MANUAL
1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093 PHONE [phone]
FAX [phone]
MODEL NO.
LS67522HP
STARTING SERIAL #:
L110-075001
LS87522HP
STARTING SERIAL #
L110-075001
Manufacturing quality lawn care equipment since 1945
Safety
Assembly
Operation
Service and Adjustment
Repair Parts
Made In The
USA
IMPORTANT
swisherinc.com
18025
Rev. 11-048
Model LS87522HP shown

2
LIMITED WARRANTY
TABLE OF CONTENTS
WARRANTY………………....….2
SAFETY..……………………….3-4
TOWING..….……..……………..5
OPERATION……………………6-8
MAINTENANCE.…………………….8
DECALS…..………….……………….9
PARTS BREAKDOWN…………….10-14
SPECIFICATIONS..…………………17
The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in
materials and workmanship for the period's shown below beginning from the date of purchase by the original
consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or
workmanship. This warranty is subject to the following limitations and exclusions:
Engine Warranty All engines utilized on our products have a separate warranty extended
to them by the individual engine manufacturer. Any engine service
difficulty is the responsibility of the engine manufacturer and in no
way is Swisher or its agents responsible for the engine warranty. Engine
warranty and contact information is as shown in the engine owners
manual.
Hydraulic System 1 Year
Steel Components 3 Years
Commercial Use The warranty period for this product when used for commercial or rental
is limited to ninety (90) days from the date of original purchase.
Limitation This warranty applies only to products which have been properly
assembled, adjusted, and operated in accordance with the instructions
contained within this manual. This warranty does not apply to any
product of Swisher that has been subject to alteration, misuse, abuse,
improper assembly or installation, shipping damage or to normal wear of
product.
Exclusions Excluded from this warranty are normal wear items, normal or routine
adjustments, and normal or routine maintenance.
In the event you have a claim under this warranty, you must return the product to an authorized service dealer.
All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or
repair under this warranty shall be borne by the purchaser. Should you have any questions concerning this
warranty, please contact us toll-free at 1-800-222-8183. The model number, serial number, date of purchase,
and the name of the authorized Swisher dealer from whom you purchased the splitter will be needed before any
warranty claim can be processed.
THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS
STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of
consequential damages or limitations on how long an implied warranty may last, so the above limitations or
exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights,
which vary from state-to-state. This is a limited warranty as defined by the Magnuson-Moss Act of 1975.

WARNING: The engine exhaust from this product contains chemicals known to the state of California to
cause cancer, birth defects or other reproductive harm.
DANGER: Your log splitter was built to be operated according to the rules for safe operation in this manual.
As with any type of power equipment, carelessness or error on the part of the operator can result in serious
injury. If you violate any of these rules, you may cause serious injury to yourself or others.
•Read and understand the manual. Learn to operate this equipment in a safe manner. Familiarize
yourself with all of the controls in a safe environment before starting to work with this machine.
•DO NOT under any circumstances alter this log splitter. This equipment was designed and engineered
in accordance with operating instructions. Altering this equipment, or using this equipment in such a
way as to circumvent its design capabilities and capacities, could result in serious injury or fatality and
WILL VOID THE WARRANTY.
•Allow ONLY responsible adults who have read this manual to operate this machine. NEVER allow
children to operate this machine.
•NEVER operate or allow someone to operate this equipment while under the influence of alcohol,
drugs or medication. Being coherent is essential for safety.
•ALWAYS use outdoors with adequate ventilation. DON’T run the engine in an enclosed area.
Exhaust gases contain carbon monoxide. This odorless gas can be deadly when inhaled.
•NEVER use splitter for any other purpose than splitting wood. Any other use can result in injury.
Your splitter is a precision piece of power equipment, not a toy. Therefore, exercise extreme caution at
all times.
•ONLY a single operator is to load and operate the log splitter. KEEP all others, including pets and
children, a minimum of 20 feet away from your work area. More accidents occur when more than one
person operates the log splitter than any other time.
•ALWAYS wear protective gear such as safety goggles, protective hearing device, steel-toed
shoes, and
tight-fitting gloves without drawstrings or loose cuffs.
•NEVER wear loose clothing or jewelry that can be caught by moving parts of the splitter and pull you
into it. Keep hair away from moving parts.
•NEVER operate your splitter on wet, muddy, or icy surfaces. KEEP work area clean of split wood.
Safe footing is essential in preventing accidents.
•ONLY operate splitter on level ground with wheels blocked, not on the side of a hill. It could tip, or
rolling logs, poor footing, etc. could cause an accident.
This Safety Alert Symbol indicates important messages in t
his manual.
When you see this symbol, carefully read the message that follows and be
alert to the possibility of personal injury.
Read this manual completely. This machine can amputate hands, feet, and throw objects.
Failure to observe the following safety instructions could result in serious injury or death.
3
SAFETY PRECAUTIONS

4
•
NEVER operate your splitter near a flame or spark. Hydraulic oil and gasoline are flammable and can
explode.
•NEVER fill gas tank while the engine is hot or running. Allow the engine to cool before refueling.
•This unit is equipped with an internal combustion engine and should not be used on or near any
unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is
equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used it
should be maintained in effective working order by the operator.
-NOTE-
In the state of California, the above is required by law (Section 442 of the California Public Resources Code).
Other states may have similar laws. Federal laws apply on federal lands. A spark arrester muffler (optional
by manufacturer) is available at your nearest engine dealer. Check legal requirements in your area.
•ONLY use your hands to operate the control lever. NEVER use foot, knee, rope or any extension device.
•Split ONLY one log at a time. NEVER attempt to split two logs on top of each other.
•NEVER place hands or feet between log and splitting wedge or between log and ram during forward or
reverse stroke. ALWAYS keep fingers clear of splits that open in log during splitting operation.
•DO NOT straddle or reach across the splitting area while operating the splitter.
•
DO NOT step over splitter when the engine is running. You may trip or accidentally activate the splitting
wedge. Walk around to get to the other side.
•NEVER attempt to load splitter while splitting wedge is in motion. When loading log splitter, place
hands on the sides of the log, not the ends.
•NEVER attempt to split woods across the grain. Wood may burst or fly out of your splitter and result in
serious injury.
•NEVER leave your splitter unattended with the engine running. Shut off the engine if you are leaving
your splitter, even for a short period of time. Someone could accidentally activate the ram and be injured.
•Both ends of the log should be cut as squarely as possible to prevent the log from sliding out of the
splitter during operation. Log length should be kept to 25 1/2” or less.
•NEVER operate your splitter while it is attached to the tow vehicle.
•BEFORE towing, be certain that the spl
itter is securely attached to the towing vehicle and that the support
leg, beam and cylinder are secured in there respective towing positions.
•NEVER allow persons to ride on splitter. DO NOT carry any cargo or wood on your splitter. It may fall
off and cause an accident.
•DO NOT loosen or remove any hydraulic fitting, line or reservoir cap while your splitter or engine is
running.
•Fluid escaping from a very small hole can almost be invisible. DO NOT check for leaks with your hand.
See maintenance section for instructions. IF injured by escaping fluid, see a doctor at once. Serious
infection or reaction can develop if proper medical treatment is not administered immediately.
•DO NOT operate your splitter in poor mechanical condition or when it is need of repair.
•ALWAYS disconnect the spark plug wire and place the wire where it cannot contact the spark plug, to
prevent accidental starting the engine when setting up, transporting, adjusting or repairing.
SAFETY PRECAUTIONS

•
Do not allow persons to ride on splitter. Do not carry any cargo or wood on your
splitter. It may fall off and endanger vehicles that are following you.
•Be sure support leg is in the travel position and coupling secure. This must also be
retracted so not to interfere while towing. Retract support leg by removing pin,
pivoting up, and replacing pin.
•Never exceed 45 MPH while towing your splitter. Be extra cautious when traveling
over rough terrain, especially over railroad tracks.
•Always be careful while backing your splitter. You could jackknife your log splitter
if not careful.
•Before using splitter, disconnect it from tow vehicle. A log could easily be pushed
forward into the vehicle.
•See tire and wheel specifications for PSI while towing.
•Be aware of the extra length of splitter while turning, parking, crossing intersections,
and in all driving situations.
•
OPERATION INSTRUCTIONS
POSI-LOCK COUPLER
ADJUST COUPLER LOCKING PRESSURE ON BALL BEFORE USE. PLACE HANDLE IN LOCKED
POSITION WITH BALL IN COUPLER. TIGHTEN LOCKNUT AGAINST TENSION SPRING SO THAT
COUPLER IS NOT LOOSE ON BALL. CORRECT ADJUSTMENT WILL ALLOW HANDLE TO BE
RELEASED WITH MODERATE PRESSURE APPLIED TO HANDLE.
TO OPEN, PULL UP ON COUPLER HANDLE AND ROTATE FORWARD. PLACE COUPLER ON BALL
WHEN BALL IS COMPLETELY NESTED IN BALL SOCKET, ROTATE COUPLER HANDLE
BACKWARD UNTIL HANDLE IS IN LOCKED POSITION.
AFTER TOWING FOR 50 MILES, CHECK COUPLER FOR TIGHTNESS ON BALL. ALWAYS CHECK
TIGHTNESS BEFORE TOWING. BE SURE COUPLER HANDLE IS IN LOCKED POSITION.
WARNING:
NEVER EXCEED WEIGHT CAPACITY AND ALWAYS USE SAFETY CHAINS. ALWAYS USE
CORRECT BALL SIZE, MAKING SURE BALL IS COMPLETELY INSERTED INTO COUPLER. LOCK
COUPLER HANDLE SECURELY BEFORE TOWING. ALWAYS CHECK FOR DAMAGES AND
REPLACE IF DAMAGED. AVOID SHARP TURNS AND STEEP VERTICAL ANGLES WHEN TOWING.
5
TOWING SAFETY

6
This log splitter has been mostly assembled at the factory. Refer to uncrating and assembly instructions to complete the
final assembly step. Refer to the drawings and part lists should it become necessary to disassemble the unit for repair or
replacement of parts.
Inspect all components for damage. If you believe you have a damaged part please contact customer service immediately
at 1-800-222-8183.
WARNING: Exercise extreme caution, as parts are very heavy. Sufficient persons or mechanical handling equipment
should be used.
OPERATION
INTENDED USE: This log splitter is intended and designed to only split wood. NEVER use for any other purposes.
Doing so can cause injury or VOID THE WARRANTY.
IMPORTANT: This unit is shipped with oil but without gasoline in the engine. After assembly, see separate Engine
Manual for proper fuel and oil recommendations.
WARNING: DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE AND
HYDRAULIC RESERVOIR.
FILLING THE HYDRAULIC RESERVOIR
Fill the hydraulic reservoir to within the hydraulic operating range as marked on the tank with general-purpose automatic
transmission fluid or general-purpose hydraulic fluid. After the hydraulic reservoir and the engine crankcase are filled
correctly with their respective oils, start the engine. Remember to set the throttle and turn on the fuel shut-off valve. The
hydraulic pump should prime itself. With the engine running, move the hydraulic valve lever toward the wedge. This will
cause the cylinder to extend and expel air. When the cylinder is fully extended, retract it. Repeat this procedure several
times. (An erratic movement of the cylinder indicates that there is air in the system). Once the cylinder has a smooth and
constant speed indicating that all air has been expelled, add fluid until the level is within the indicated range as marked on
the tank.
START UP
WARNING: DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE AND
HYDRAULIC RESERVOIR.
See separate Engine Manual for fuel and oil recommendations. If applicable your log splitter has come equipped with a
fuel shut-off valve for towing purposes.
Before starting engine make sure crankcase is filled correctly with oil and the proper fuel has been used. The engine will
only start when the throttle lever and fuel shut-off valve if applicable are turned to their ON positions.
STARTING INSTRUCTIONS
See Engine Manual
COLD WEATHER START UP
The Cold Weather Clutch enables the engine to be started without having to pull through cold, thickened
hydraulic fluid. Simply push the handle into locked position. Start engine, let it warm up, and release Cold
Weather Clutch.
ASSEMBLY

7
SPLITTER OPERATION
1. Set up the log splitter in a clear, level area and block the wheels. The suction port on the tank should
always be on the lower side of the log splitter.
2. Place a log on the beam, against the foot plate. Make sure the log is securely on the foot plate and up
against the beam.
3. Depress the valve lever so that the cylinder will drive the push block into the log. Extend the cylinder
until the log splits or to the end of its stroke. If the log has not completely split after the cylinder has
reached the end of its extension, retract the cylinder. NOTE: Leaving the valve in the “actuate” position
at the end of the stroke may damage the pump. Always use extra care when splitting logs with ends that
are not square.
NOTE: To extend the life of the hydraulic cylinder, avoid “BOTTOMING OUT” the cylinder.
TOWING SAFETY
This unit should not be towed on any street, highway, or public road without checking the existing federal, local,
and state laws. Any licensing or modifications such as taillights, etc., need to comply with existing federal, local,
or state vehicle requirements is the sole responsibility of the purchaser. Obey all regulations when towing on
public roads and highways. See also SAFETY PERCAUTIONS.
Turn the fuel shut-off valve if applicable OFF to prevent flooding of the engine while traveling.
Be careful when backing up. You can easily jack-knife your splitter.
TOWING AT NIGHT
The requirements for taillights are based on States regulations. Some states allow towing at night as
long as the towed equipment does not visibly impair the tow vehicle taillights. This is based on a state,
to state requirements. The customer is responsible for meeting the states requirements.
If a “Statement of Origin” is required in your state, see your local dealer to receive one.
HYDRAULIC SAFETY
The hydraulic system on your splitter requires careful inspection along with the mechanical parts. Be sure to
replace any frayed, kinked, cracked or otherwise damaged hydraulic components. Just because it isn’t leaking
today doesn’t mean that it will not fail tomorrow.
Fluid escaping from a very small hole can almost be invisible. Do not check for leaks with your hand. Escaping
fluid under pressure can have sufficient force to penetrate skin causing serious personal injury or even death.
Leaks can be detected by passing a piece of cardboard or wood over the suspected leak and looking for
discoloration. IF injured by escaping fluid, see a doctor a
t once. Serious infection or reaction can develop if
proper medical treatment is not administered immediately.
Should it become necessary to loosen or remove any hydraulic fittings, lines or reservoir cap, be sure to relieve all
pressure by shutting of the engine and moving the control handle back and forth several times.
NEVER remove the cap from the hydraulic tank or reservoir while the unit is running. Hot oil under pressure
could result in serious injury. See also SAFETY PERCAUTIONS.
The pressure relief valve on your splitter is preset at the factory. DO NOT adjust the
valve. Only a qualified technician should perform this adjustment.
OPERATION

8
WARNING:
DISCONNECT THE SPARK PLUG BEFORE PERFORMING ANY MAINTENANCE.
Consult the operating and maintenance instructions of the engine manufacturer for engine care.
Always check the oil level of the hydraulic reservoir before operation. Operating without an adequate oil
supply will cause severe damage to the pump. Change the hydraulic fluid in the reservoir after every 100 hours of
operation. Change the hydraulic filter after every 50 hours of operation (use only a 10 micron hydraulic filter).
Periodically check that all nuts, bolts, screws, clamps and fittings are tight and secure.
To keep your splitter in top working condition perform all recommended maintenance procedures before you use
your splitter.
If the wedge becomes dull or nicked a grinder or sharpening tool can be used to sharpen it.
Completely drain the fuel tank prior to storage. Always store gasoline in an approved, tightly sealed container. Store
container in a dry, cool place with adequate ventilation. Keep fuel away from areas where fumes could contact open
flame, pilot light or sparks.
Be aware of the environment when disposing of used petroleum products. Please dispose of used hydraulic
fluid, engine oil and any by products from the maintenance of your splitter at approved recycling centers.
Should it become necessary to disassemble the unit for repair or replacement of parts, refer to the drawings and parts
list on the following pages. Exercise extreme caution, as some parts are very heavy and will require sufficient
persons or mechanical handling equipment.
Your Swisher Log Splitter has been produced with components designed specifically to this machine. Although
standard springs, hardware and ect may look similar to parts used on other machinery, they may in some cases be
made of a different construction and/or materials. All replacement parts must meet manufacturer’s
specifications.
The operation of any splitter can produce foreign objects to be thrown into the
eyes, resulting in severe eye damage. Always wear certified safety glasses or
wide-vision safety goggles over spectacles before staring any splitting machine
and while operating such a machine.
The operation of any splitter produces sound waves that are damaging to the
human ear. Ear protection is recommended.
MAINTENANCE & STORAGE

12494 – HYDRAULIC FILL PLUG
DECAL
11427 – DANGER DECAL
12492 – OPERATOR INSTRUCTION
DECAL
OD16 – FUEL SHUT OFF DECAL 17943 – COLD WEATHER DECAL
SAFETY DECALS
Replace decals immediately if damaged.
9
12549 – DO NOT EXCEED 45 MPH
DECAL

10
PARTS BREAKDOWN
ASSEMBLY DETAIL
ITEM # QTY. PART # DESCRIPTION
1 16630TK MOTORBASE - WLEDMENT; TXTBLK
2 1 N/A SEE TONGUE DETAIL (PAGE 14)
3 2 2203S WHEEL HUB BEAING SEAL FOR WT7002A
4 2 7296 WHEEL/TIRE - W/ BEARINGS AND SEAL (4 PLY)
5 2 2203DC WHEEL HUB DUST COVER FOR WT7002A
6 4 2203B WHEEL HUB BEARING FOR WT7002A
7 2 2203CN WHEEL HUB CASTLE NUTFORWT7002A
8 2 NB633 PIN - COTTER 1/8" X2"(EXT PRONG CRBN STL)
9 2 NB179 Washer - 3/4ID X 1 1/4OD 18GA ZY
10 2 26X249 SCREW - .312-18 X .75
11 1 16635TK TANK - HOLD DOWN; TXT BLK
12 1 17618 TANK - 2.5 GALLONS WITH FITTINGS
Not Shown 18134 Cap
Not Shown 12441 Grommet
Not Shown LS5001 Hose Clamp No. 12
Not Shown LS4999 Hose Clamp No. 16
13 2 AS116 EDGING - TRIM STRIPS
14 1 N/A SEE PUMP DETAIL (PAGE 11)
15 1 N/A SEE FILTER DETAIL (PAGE 12)
16 1 N/A SEE IDLER DETAIL (PAGE 11)
17 1 N/A SEE BEAM DETAIL (PAGE 13)
18 1 N/A SEE MOTOR DETAIL (PAGE 15)
19 1 NB180 NUT - 1/4-20 NYLOC
20 1 V139EB EYEBOLT - 1/4-20 X3/4
Not Shown 1 7289 Hose - Hydraulic Pressure
Not Shown 1 7346 Hose - Suction, 20"
Not Shown 1 16067 Hose - Return 55"
Not Shown 1 16637 Hose - Return, 3/4" X 18.5"

11
PUMP DETAIL
IDLER DETAIL
PARTS BREAKDOWN
ITEM NO. QTY. PART NO. DESCRIPTION
1 1 16625TK MOUNT - PUMP
2 1 14926 HYDRAULIC PUMP
3 8 NB596 BOLT - 5/16" X 18 UNC X .75" FLANGE HEAD
4 8 NB170 NUT - 5/16-18 SERR FLANGE
5 1 7306 Pulley- Pump 4.25"
6 1 NB312 5/16-18 X 1/2 SSC With Loctite H
7 1 024002 KEY WOODRUFF 3
ITEM NO. QTY. PART NO. DESCRIPTION
1 1 16626 Idler, Sliding / Cold Weather
2 1 2077 HANDLE GRIP, PIVOT
3 1 NB107 3/8-16 X 1 1/2 HCCG
4 1 NB272 3/8 SAE WASHER
5 1 NB182 3/8-16 NYLOC NUT
6 1 B527 Idler Pulley OD-3.25", ID-3/8"
7 2 6037 IDLER BUSHING
8 1 NB280 NUT - LOCKING, 2 WAY 3/8-16 & WAS GR A
9 1 6040 IDLER SPACER
10 1 NB302 Bolt - 3/8-16 X 1 3/4 HCC GR5 ZY
10

12
ITEM # QTY. PART # DESCRIPTION
1 1 7287TK Valve Control Splitter
2 1 NB522 1/4 X1 CLEVIS PIN
3 1 7424 Master Link
4 1 7423 HANDLE VALVE
5 1 7425 Valve Handle Grip
6 1 NB-597 3/32 X3/4 COTTER PIN
VALVE DETAIL
PARTS BREAKDOWN
ITEM # QTY. PART # DESCRIPTION
1 1 NB521 BOLT - 5/16-18 X5 1/2 HCC GR5 ZP
2 1 17595TK SPACER - FILTER GUARD; TXT BLK
3 4 NB170 NUT - SERR FLANGE 5/16-18 ZY CASE HRD
4 2 7329 LINE - FITTING RETURN (4501-12-12) YZ
5 1 LS1112 HEAD - FILTER (FPC3012NXXR4X)
6 1 LS1113 FILTER - ELEMENT
7 1 17627TK MOUNT - WITH FILTER GAURD; TXT BLK
8 2 NB596 BOLT - SERR FLANGE, 5/16-18 X3/4 GR 5
9 2 NB250 BOLT - 1/4-20 X3/4 GR5 ZY
10 2 NB135 WASHER - 1/4 SPLIT LOCK, MEDIUM DUTY
FILTER DETAIL
NOTE: The directional flow
arrows on the filter head (LS1112)
should be pointing away from the
hydraulic tank on the 28 Ton and
22 Ton models

13
BEAM DETAIL
PARTS BREAKDOWN
ITEM NO. QTY . PART NO. DESCRIPTION
1 1 14900TC Weldment - LS W 6X20 I- Beam
2 1 14622TK WEDGE WELDMENT - LOG SPLITTER
3 2 14619TK SPACER - WEDGE, LOG SPLITTER
4 2 14620TK PLATE - WEDGE BOTTOM, LOG SPLITTER
5 6 NB643 BOLT - CARRIAGE 1/2-13 X 2 1/2 GR5 ST ZY
6 6 NB213Z NUT - 1/2-13 GR2 ZP
7 6 NB508 500 LOCK WASHER
8 8 NB555 1/2 USS Flat Washer ZP
9 1 7284TK CYLINDER 4" X 24" X 1 3/4"
10 1 7287TK Valve Control SplitterAssy
11 1 7292 Pipe Nipple 24SA-08
12 2 7291 ELBOW - HYDRAULIC 1/2 X 1/2 THREAD ZY
13 1 7329 Fitting Return Line (4501-12-12)
14 1 7288 Line Assembly -St at ionary
15 1 7293 Pin- Cylinder to Beam
16 2 NB642 COTTER - HAIRPIN # 23-09 .093 X 1 13/16
17 1 12669 BOLT - 1/2-13 X 3 1/4 GR8 ALLOY ZY
18 2 TR150W Washer, Front Wheel (Heat Trtd)
19 1 NB121 1/2-13 2-Way Jam Lock Nut
20 1 NB151 BOLT
21 1 NB688 Nut - 1/2 -13 Nyloc, Jam
22 1 H11 Safety Hitch Pin

14
PARTS BREAKDOWN
TONGUE DETAIL
ITEM NO. QTY. PART NO. DESCRIPTION
1 1 12346TK Log Splitter Tongue
2 3 NB649 3/8-16 X 3 1/2 GR5
3 12 NB272 3/8 SAE WASHER
4 5 NB182 3/8-16 NYLOC NUT
5 1 NB150 3/8 - 16 x 3
6 2 10177 WASHER - FENDER 3/8 X 1 1/2, CRBN STL GR2
7 1 14924TK Stand - Folding
8 1 NB606 1/2" x 3" Bent Pin w/Hair Clip
9 1 7365 2" Ball Coupler
10 2 7366 Safety Chain W/S Hook
11 2 7840Z Lat ch Pin Guide Bushing
12 1 NB645 BOLT - 3/8-16 X 4 HCC GRD5 ZY

15
ENGINE DETAIL
PARTS BREAKDOWN
ITEM # DESCRIPTION PART #
1 Engine N/A
2 Bolt 5/16-18 X1 1/4 Serr. Flange NB253
3 Bolt 5/16-18 X2 1/4 Serr. Flange NB622
4 Nut 5/16-18 Serr. Flange NB170
5 3/16 X1 Keystock 9030
6 Engine Pulley 7/8" ID 7323
7 5/16-18 X1/2 Set Screw w/Loctite NB312
8 Washer Belleville 699
9 Bolt 3/8-24 X1 w/Loctite NB238N
NOTSHOWN Fuel Shut Off Valve (Inline) 7414
NOTSHOWN Fuel Line Clamp 6FLC
Note: Install pulley collar up and
bottom side of pulley flush
with end of engine shaft.

16
BELT ROUTING DIAGRAM
(VIEWED FROM UNDERSIDE OF SPLITTER)
Problem Cause Remedy
Engine fails to start. 1. Spark plug wire disconnected. 1. Connect wire to spark plug.
2. Fuel tank not full enough or stale fuel. 2. Fill tank full with clean, fresh gasoline.
3. Throttle control lever not in correct
starting position. 3. Move throttle lever to FAST position.
4. Choke not in CHOKE position. 4. Move choke to CHOKE position.
5. Engine not primed properly. 5. Prime engine.
6. Fuel valve not ON or blocked fuel line. 6. Turn on fuel valve or clean fuel line.
7. Faulty spark plug. 7. Clean, adjust gap, or replace spark plug.
Engine is hard to start or
runs erratic. 1. Spark plug wire loose. 1. Connect and tighten spark plug wire.
2. Unit running on CHOKE. 2. Move choke lever to OFF position.
3. Blocked fuel line or stale fuel. 3. Clean fuel line; fill tank with clean, fresh
gasoline
4. Water or dirt in fuel system. 4. Drain fuel tank. Refill with fresh gasoline.
5. Dirty air cleaner. 5. Clean or replace air cleaner.
6. Carburetor out of adjustment. 6. See authorized service center.
Cylinder rod will not extend
or contract. 1. Cold weather clutch not engaged. 1. Engage cold weather clutch.
2. Broken or improperly installed belt. 2. Replace or reinstall belt.
3. Low hydraulic fluid. 3. Fill hydraulic tank to correct fluid level.
4. Hydraulic lines blocked. 4. Flush and clean hydrualic system.*
5. Damaged or broken pump. 5. See authorized service center.
6. Damaged control valve. 6. See authorized service center.
Cylinder rod is slow or
erratic while extending and
contracting.
1. Low hydraulic fluid. 1. Fill hydraulic tank to correct fluid level.
2. Contaminated hydraulic fluid. 2. Drain fluid, flush system, and refill.
3. Excessive pump inlet vacuum. 3. Make certain pump hoses are clear and
unblocked. Make certain hose in not
collapsing under suction.
4. Damaged pump. 4. See authorized service center.
5. Damaged control valve. 5. See authorized service center.
6. Internal cylinder damage. 6. See authorized service center.
Leaking Cylinder 1. Broken seals. 1. See authorized service center.
2. Scored cylinder. 2. See authorized service center.
TROUBLESHOOTING
ENGINE
PULLEY
IDLER
PULLEY
PUMP
PULLEY

17
NOTE: For repairs beyond those listed here, contact your nearest authorized service center.
* Flushing the reservoir tank and hoses with kerosene whenever service is performed on the tank, hydraulic pump or
valve is recommended. Contact an authorized service center.
MAINTENANCE LOG
NotesService PerformedDate of Service

SPECIFICATIONS
18
Splitting Force 22 Tons
Engine 6.75 Torque:
190CC B&S
Splitting
Positions Horizontal and
Vertical
Cylinder Size Ø4" X 24"
Pump 2 Stage
Pump Specs 11 Gallons Per
Minute
Valve Auto Return
Drive System Belt Drive 1:1
Ratio withClutch
for EasyStarting
Hydraulic
System Fluid
Capacity 11-13 Quarts
Maximum Log
length 25 1/2"
Tire Specs 4.00 X 4.80 X 8
withHighSpeed
Bearings
Metal Fenders No
MODEL LS87522HP,LS67522HP

19
SWISHER HISTORY
Back before electricity came to rural Missouri Max Swisher was producing lawn mowers
from his mother’s chicken house. Max never liked to mow grass. He installed a
gearbox on his family’s lawn mower creating a self-propelled unit. By tying one end of a
rope to the mower and the other end to a tree in the center of the yard the mower
circled the tree, shortening the rope and guiding the mower in concentric circles. Max
enjoyed relaxing under a shade tree while his invention did all the work.
Max had designed his first self-propelled rotary lawn mower to do his dirty work for him.
Neighbors noticed his new invention and began asking him to make more. Today, 60
years later, Swisher is still producing innovative lawn and garden and ATV/UTV
equipment designed to give us all more “relaxing in the shade” time.
Swisher products have been featured nationally on television programs such as Regis
and Kathie Lee and seen in publications like ATV Magazine, Country Journal, Popular
Mechanics Magazine and others. In January 2000 Popular Mechanics Magazine
named Max’s zero turning radius riding mower one of the 20th century’s top household
inventions.
Swisher offers value and function in its products to meet your grounds maintenance
needs.
CELEBRATING OVER 65 YEARS OF INNOVATION
SINCE 1945

OWNER’S
MANUAL
MODEL NO.
LS67522HP
LS87522HP
HOW TO ORDER
REPAIR PARTS:
LOG SPLITTER
Each Log Splitter has its own serial number. Each engine has
its own serial number. The serial number for the Log Splitter
will be found on the right hand side of the hydraulic oil
reservoir. The serial number for the engine will be found on
the top of the blower fan housing.
All Log Splitter parts listed herein may be ordered directly
from Swisher, your nearest Swisher dealer, or from our
website.
All engine parts may be ordered from the nearest dealer of the
engine supplied with your log splitter . Parts subject to change
without notice.
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INFORMATION AVAILABLE:
* PRODUCT – SWISHER LOG SPLITTER
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
* ENGINE MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER
* PART DESCRIPTION
www.swisherinc.com
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER
1602 CORPORATE DRIVE
WARRENSBURG, MO 64093
SWISHER