Swisson UM-XSW-D0-LEN-V03-01 User manual

XSW
DMX Splitter / Booster,
Wireless DMX Transmitter &
Wireless DMX Receiver
User Manual

2
UM-XSW-D0-LEN-V03-01.DOCX 2015-03-26

3
Index
Index.................................................................................................................................................................................. 3
Introduction ......................................................................................................................................................................4
Safety Information ............................................................................................................................................................ 5
Mains Connection .............................................................................................................................................................6
XSW Block Diagram........................................................................................................................................................... 6
Transmission Technologies ............................................................................................................................................... 6
Input Section.....................................................................................................................................................................7
Input and "Thru" Port .......................................................................................................................................................7
Line Termination ...............................................................................................................................................................7
Output Ports......................................................................................................................................................................8
Wireless Port and Operating Modes................................................................................................................................. 8
Establishing a Wireless Link .............................................................................................................................................. 9
Link LED...........................................................................................................................................................................10
Multiple Links..................................................................................................................................................................11
Limits on Simultaneous Links.......................................................................................................................................... 13
Position of the Antenna ..................................................................................................................................................13
Technical Data.................................................................................................................................................................15
Ordering Information......................................................................................................................................................16

4
Introduction
The XSW combines CRMX™ / W-DMX™ wireless DMX technology with all of the advantages of the DMX splitters
from SWISSON.
An XSW can be used as a DMX splitter, as a wireless DMX transmitter or as a wireless DMX receiver. The DMX splitter
functionality is always available, regardless of whether the device is configured as a transmitter or as a receiver. If
only the splitter functionality is used, the wireless part can be switched off. All ports, including the input port of the
XSW are optically isolated.
Several XSW variants are available with various housings and connector types. Depending on the model, one of the
two most established wireless DMX transmission technologies, either W-DMX™ (by Wireless Solution) or CRMX™ (by
LumenRadio), is used. This allows for a maximum of compatibility with existing wireless DMX equipment.
The built-in power supply allows for a reliable operation in a wide voltage range.
Fields of Application
Architectural lighting
TV sets
Theme parks
Theater
Multimedia shows
Concert lighting
Typical Application
Transmitter
Receiver mode
Receiver mode
Light controller
board
Unpacking
The XSW is packaged in a cardboard box including the following items:
The device
1 antenna
This user manual

5
Safety Information
Consider the following notes absolutely when you set up, connect and use the XSW.
This product is not for household use. Read this manual before operating the device, follow the
safety precautions and observe all warnings in this manual.
Use this device only in accordance with local laws and regulations.
Safety Precautions
Disconnect the device from AC power before removing any cover or part, including any
fuse and when not in use.
Ensure that the device is electrically connected to ground (earth).
Use only a source of AC power that complies with local building and electrical codes and
has both overload and ground fault (earth fault) protection.
Before using the device, check that the power distribution equipment and cables are in
perfect condition and rated for the current required of all connected devices.
Isolate the device from power immediately if the power cable or the power plug is in any
way damaged, defective or wet, or if they show signs of overheating.
Do not expose the device to rain or moisture.
Do not operate the device if any cover or component is missing, damaged or deformed.
Refer any service operation not described is this manual to SWISSON.
Provide unrestricted airflow around the device.
Do not operate the device if the ambient temperature exceeds 55°C (131°F).
Do not modify the device in any way not described in this manual or install other than
genuine SWISSON parts.
Do not attempt to bypass any fuse. Replace any defective fuse with one of the specified
type and rating only.
When suspending the device, ensure that the supporting structure and all hardware used
can hold at least 10 times the weight of all devices suspended from them.
When suspending the device, install a secondary attachment such as a safety cable that is
approved by an official body such as TÜV as a safety attachment for the total weight it
secures. The safety cable must comply with EN 60598-2-17 Section 17.6.6 and be capable
of bearing a static suspended load 10 times the weight of the device.
Make sure that any external cover and rigging hardware is securely fastened.
Block access below the work area whenever installing, servicing or moving an overhead
device.
Do not use the device in areas where it is exposed to direct sunlight.

Mains Connection
The US versions are delivered by SWISSON with an "Edison Plug" (NEMA-5-15). These models are labeled with a type
designation ending in "-US". International versions on the other hand, are delivered without any plug. SWISSON
distributors or dealers may however deliver the devices with a country specific plug.
US Versions (-US suffix) International Versions
Brown : Phase Blue : Neutral
Yellow/Green : Earth
Wire (US System)
Wire (EU System)
Symbol
Live
Black
Brown
L
Neutral
White
Blue
N
Ground (Earth)
Green
Yellow/Green
or
Consult a qualified electrician if you have any doubts about proper installation.
The socket where the device is plugged in must be close to the device and easily accessible.
XSW Block Diagram
ProtectionProtectionProtectionProtection
Optical
Isolation
Optical
Isolation
Optical
Isolation
Optical
Isolation
ControlLogic
Protection
Transceiver
Out Port 4Out Port 3Out Port 2Out Port 1InPort ThruPort
Line
Termination
Termination
TransmitterTransmitterTransmitterTransmitter
Optical
Isolation
HF
Antenna
Transmission Technologies
Depending on the model, XSW uses one of the following transmission technologies.
1) CRMX™ (Cognitive Radio MultipleXer) by LumenRadio.

7
2) W-DMX™ by Wireless Solution.
Both types are very reliable and widely spread in the professional lighting industry. Refer to Ordering Information on
page 16 for a full list of the available model types.
Input Section
The Power LED shows if the device is powered when the power supply unit of the XSW
is working.
dmx
The Signal LED lights up in green, when a valid DMX signal is received at the input port.
When a faulty DMX signal is received, the Signal LED lights up in red.
The XSW has a built-in line termination. This can be activated or deactivated by pressing
the termination button.
Input and "Thru" Port
The "Thru" port is hardwired to the input port and allows to daisy-chain the devices even when the XSW is not
powered. On XSW models with 5-pin XLR connectors, the pins 4 and 5 are also connected to the corresponding pins
of the "Thru" port. On all other models, the pins 4 and 5 are not available.
Protection Transceiver
Line
Termination
InputPort ThruPort
1
2
3
4
5
1
2
3
4
5
Line Termination
All XSW models have a built-in line termination. The termination is activated / deactivated by pressing the Line
Termination button.
Line Termination
dmx

8
Output Ports
The output section
dmx
The Signal LED of the output section lights up when DMX data is available at the output
ports.
Each output port is individually optically isolated, meaning that it is totally isolated from the other output ports and
from the input selection.
The pins 4 and 5 of the output ports on the models with 5-pin XLR connectors are not connected.
OutputPort
1
2
3
4
5
ProtectionTranceiver
Optical
Isolation
Port Supply
Control
Logic
ControllerSupply
n.c.
Bias
Network
Wireless Port and Operating Modes
r :receiverx
t :transmitterx
link:press
unlink:press3sec
Operating Modes
The XWL has three operating modes as described below. The Mode button, which is located above the Rx and the Tx
LEDs, is used to select the current operating mode.
Splitter Only mode. When both, the Rx LED and the Tx LED are off, the XSW operates as a splitter only. The
wireless port is switched off.
Receiver mode. When the Rx LED is on, the XSW works as a wireless receiver. The received DMX data is
forwarded to the DMX output ports. The DMX input port has no function in this mode.
Transmitter mode. When the Tx LED is on, the XSW operates as a wireless transmitter. The DMX data from
the DMX input port is transmitted and is also available at the DMX output ports.

9
Wireless Port
Link button and Link LED. The Link button is used to link a transmitter to one or multiple receivers. The Link
LED shows if the device is linked.
Signal strength indicator. In Receiver mode, four green LEDs display the signal strength. In Transmitter mode,
they indicate that the transmitter is active by flashing alternately.
Locking the Device
Lock button and Lock LED. The Lock LED lights up in red when the Lock function is activated. In this case, the
Mode and the Link buttons on the left of the Lock button are disabled. This may prevent an unintended
manipulation of the operating mode or of the link status. The Lock button is used to enable/disable the Lock
function. It is only accessible with the use of a tool like a paper clip.
Establishing a Wireless Link
To transmit DMX data wirelessly, a transmitter and one or more receivers are used. The receiver has to be linked to
the transmitter(s). This is achieved as shown below.
Transmitter mode
Receiver mode
Receiver mode
1) Press the Mode button of the device that is intended
to be used as the transmitter repeatedly until the Tx
LED is turned on in order to activate the Transmitter
mode.
2) On each device that is intended to be used as a
receiver: Put the device into receiver mode by
pressing the mode button multiple times until the Rx
LED lights up.
Transmitter mode
3sec
Receiver mode
Receiver mode
3sec 3sec
3) On transmitter: Press and hold the Link button for 3
seconds to unlink all devices previousely linked to
that transmitter.
4) On each receiver: Press and hold the link button for
3 seconds to unlink the device from any transmitter.

10
Transmitter mode Link
Link
On transmitter: Press the link button to link all unlinked receivers in the range of the transmitter.
Link LED
The Link LED shows different status information depending on the model and operating mode.
XSW-TR-CRMX models

11
XSW-TR-WDMX models
The Link LED is always off in Splitter Only mode.
Multiple Links
Multiple DMX universes can be transmitted wirelessly using several transmitters as described below.
1) Put the units into their designated mode.
Transmitter mode
Receiver mode Receiver mode Receiver mode Receiver mode
Transmitter mode

12
2) Unlink all devices from previous links.
Transmitter mode
Receiver mode Receiver mode Receiver mode Receiver mode
Transmitter mode
3sec 3sec 3sec 3sec
3sec3sec
3) Link the first universe by pressing the link button on the first transmitter. It will link to all unlinked receivers.
Transmitter mode
Receiver mode Receiver mode Receiver mode Receiver mode
Transmitter mode
4) Unlink receivers you want to link to the second transmitter.
Tranmitter mode
Receiver mode Receiver mode Receiver mode Receiver mode
Tranmitter mode
3sec 3sec
Note: You can switch the receivers you want to link to the second transmitter temporarily to Splitter only
mode or you can switch them off. This prevents the need to unlink these receivers from the first transmitter.

13
5) Link the second universe by pressing the link button on the second transmitter. It will link to all unlinked
receivers.
Transmitter mode
Receiver mode Receiver mode Receiver mode Receiver mode
Transmitter mode
Limits on Simultaneous Links
Each transmitter needs bandwidth and there might also be a lot of other devices like Wi-Fi using the same frequency
band. It’s not recommended to use more than 4-6 transmitters on the same site.
There is no limitation for the number of receivers linked to a transmitter.
Position of the Antenna
Good Not good Bad
Try to position the antennas in parallel.
Good Bad
Avoid the operation of the XSW near the ground.

14
Bad
Good
Try to place the antennas at an elevated location. A crowd will absorb the signal.
Bad Better Best
It is recommended to place the device itself at an elevated location rather than to use an antenna cable.

15
Technical Data
Mains cable
M10/M12 threat for clamp
Eye for safety
Cable length approx.
217.5mm
Mains plug (US-Versions
112mm
45mm
482mm
112mm
45m
cable length approx. 145cm
Mains plug (US-Versions only)
Ambient temperature.................................................................. -17°C –55°C (0°F –131°F)
System latency ............................................................................. 5 ms
Broadcast power (transmitter) .................................................... 100 mW (20 dBm)
Radio frequency band.................................................................. 2.4 GHz
Mains supply ................................................................................ 100-240 VAC 50/60 Hz
Power consumption..................................................................... 4 W
DMX.............................................................................................. ANSI E1.11

16
Ordering Information
Box Versions
10 18 10
XSW-TR-CRMX-3B
Wireless DMX splitter, CRMX type, 3-pin XLR, box version.
10 18 11
XSW-TR-CRMX-5B
Wireless DMX splitter, CRMX type, 5-pin XLR, box version.
10 18 15
XSW-TR-WDMX-3B
Wireless DMX splitter, W-DMX type, 3-pin XLR, box version.
10 18 16
XSW-TR-WDMX-5B
Wireless DMX splitter, W-DMX type, 5-pin XLR, box version.
Rack Versions
10 18 20
XSW-TR-CRMX-3R
Wireless DMX splitter, CRMX type, 3-pin XLR, rack version.
Wireless DMX receiver. CRMX type. 3 pin XLR
10 18 21
XSW-TR-CRMX-5R
Wireless DMX splitter, CRMX type, 5-pin XLR, rack version.
Wireless DMX receiver. CRMX type. 5 pin XLR
10 18 25
XSW-TR-WDMX-3R
Wireless DMX splitter, W-DMX type, 3-pin XLR, rack version.
Wireless DMX receiver. W-DMX type. 3 pin XLR
10 18 26
XSW-TR-WDMX-5R
Wireless DMX splitter, W-DMX type, 5-pin XLR, rack version.
Wireless DMX receiver. W-DMX type. 5 pin XLR