Syba SY-ENC50122 User manual

1. Product Specifications
Support single HDD up to 16TB+, with a total of 5 RAID 0 set up of 80TB+ capacity
Only work with provided external 12V8A power supply. Will have the following
signal alerts once power is detected out of range:
a Yellow light signals low voltage, it may be seen by pulling off the bottom HDD
B Red light signals high voltage, it may be seen by pulling off the bottom HDD
Support RAID0/1/3/5,JBOD, and Normal Clone
Smart fan control. Support sleep mode
Transfer rate up to 5.0Gbps via USB3.0 and up to 3.0Gbps via eSATA
Support Windows、MAC、Linux OS
◼Auto-Sleep mode during data transfer via USB or eSATA. Besides POWER light,
all LED lights will turn off. Once transfer is complete, it will be back
to wake-up mode with all lights on.
◼Auto-Sleep mode once connected computer enters sleep model or shut down.
◼Auto-Sleep mode after 30 minutes without operation from USB connected
computer. Will resume once READ/WRITE on any HDD.

2. Package Contents:

3. HDD Installation Instruction
(Please do not connect the power supply while installing the hard drive.)
3.1：3.5-inch hard drive installation
1. Touch the protruding position on the top of the panel
with your fingers. Pull out the magnetic panel and
place it properly.
2. Pull out the tray by pushing down on switches in the
middle with your thumb and index finger.
3. The 3.5-inch hard disk in the extraction box is
installed without screws. Please remove the fixing
tabs on both sides of the extraction box. Put the hard
disk in the extraction box correctly, and make sure
that the screw holes at the bottom of the hard disk
are placed in the positioning posts of the extraction
box.
4. Firmly push the side clamps back into place making
sure the HDD screw holes are lined up with the
screw holes in the tray.

3.2：2.5-inch hard drive installation
5. Repeat the process with all the HDD trays. Check to
see if all the trays are inserted and locked into place
before positioning the magnetic front panel into
place.
1. Remove the clasp on the right side of the extraction
disk, and place the 2.5-inch hard disk in the position
shown on the left.
2. Turn the hard disk and the extraction disk over to the
back. Take the screws from the accessory bag to fix
the 2.5-inch hard disk. There are four screw holes.
Once done, insert the tray back into enclosure.

4. Product Description
Mobile Tray
Face Panel
FUNCTION
AND
DESCRIPTION
HDD POWER LED ：THE BLUE LEDWILL STAY ON WHEN POWERED ON
AND WILL TURN OFF DURING SLEEP MODE.
HDDACTIVITY LED ：THE YELLOW LED WILL BLINK DURING HDD
ACTIVITY (READAND WRITE).

Lower panel
FUNCTION AND
DESCRIPTION
NORMAL MODES
RAID1/3/5/10/Clone Modes
POWER LED:THE
BLUE LED WILL
STAY ON WHEN THE
UNIT IS POWERED
ON.
1-5 LED:
CORRESPONDS TO
THE HDD LIGHT
FROM TOP TO
BOTTOM,UNDER
NORMAL
CIRCUMSTANCES,
WHEN HDD 1TO 5
HAVE READ/WRITE
ACTIVITY THE
CORRESPONDING
1-5 LED WILL
FLASH BLUE
When the HDD 1-5 LED lights up in red and the E/R
lights up in red, it means that the corresponding red light has an
error in the hard disk. Please replace the defective hard drive
with a new hard disk with a capacity not less than the old hard
drive when the enclosure is powered down. If the activity light of
the new hard disk flashes blue and red alternately and the E/R
light flashes red, it means that the replacement hard disk is in the
process of data recovery (Rebuild mode), and other hard disks
will also flash blue lights at the same time. Please do not shut
down and wait patiently. The recovery speed is about 180M/ s.
E/R LED: Error/ Rebuild LED. When there is a failure to
establish a RAID mode combination, and RAID automatically
restores data after replacing the hard disk; this LED will flash
red, indicating that the disk array data is being restored. When
the RAID mode is wrong, this LED will be solid red.

Locations
Functions
Power Switch:
Power on: Push once to power on the unit.
Shut down: Push and hold for 4 seconds to shut down.
12V power input interface (5.5*2.5): (new power supply voltage
input protection)
Connect the 12V 8Apower adapter in the accessory box.
RESET switch: When you need to change the RAID mode, you need
to press this switch for a few second, and then create a new RAID
configuration mode.
Please refer to the setting method below for details.
RAID mode switch: RAID mode setting switch. See [RAID Mode
Comparison Table] for detailed settings.
USB3.0 interface: Use USB3.0 transmission cable to connect to
computer host, notebook, server, and other devices.
e-SATA interface: Use e-SATA transmission cable to connect to
computer host, notebook, server, and other devices.
Smart fan: When the hard disk is active, the fan will stay on. When
the hard disk goes into sleep mode, the fan will power down.

5.Hardware RAID setup
1. First set the initial state
2. Set RAID mode
Attention：
Before changing the RAID mode, please back up the data on the hard drive. Once the
RAID mode is changed, all data on the hard drive will be erased.

RAID mode comparison table:
Schematic diagrams of RAID setting by switches
Note: RAID1+0 can only use 4 hard drives.
ITEM
S/W1
S/W2
S/W3
MODE
1
ON
ON
ON
RAID0
2
ON
ON
OFF
RAID1/RAID10
3
ON
OFF
OFF
RAID3
4
OFF
ON
OFF
RAID5
5
OFF
ON
ON
CLONE
6
ON
OFF
ON
LARGE
7
OFF
OFF
OFF
NORMAL