Syris SY210NT Series Instruction manual

SYRIS SY210NT Series
Quick User Guide Manual
Ver : 2.00
Control up to 4 doors with in/out reader
Baud rate 2,400 - 115,200 bps

SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 1 -
SY210NT Serial Basic Menu Structure
We list SY210 basic menu structural drawing here for user to get familiar with the SY210
serial controller operation procedure. The first step is to execute the white box “ Login
procedure” to enter dark gray box “main menu” and light gray “sub-menu”, please refer
the diagram key and the direction of arrow, the function description of sub-menu will be
introduce at below document.

SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 2 -
Overview
Item Contents Page
01
Attention matter 3
02 Login/logout steps 3
03 Setup module (setup reader) 4
04 Add/delete/edit card 8
05 Add and delete fingerprint 12
06 Setup controller ID (when multiple
controllers online)
18
07 Procedure control (setup open door
button)
20

SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 3 -
01 Attention matter
Install:
When the user ready to install SY210 serial controller, please open the controller cover on
the back (TSN and SSN model) and confirm the white disconnect film has been removed.
When the user first time connect the power, all the lights flash and produce serial sound,
please proceed system replacement by click 1 key according to the controller LED display
(1：Clear)
Setup:
The controller and reader factory default ID all set to “1” Please setup ID first before
connect multiple controller or reader to avoid ID repeat cause communication failure.
Please refer the reader ID setup method of page 5 “Setup module”. And about controller ID
setup please refer page 17 “Setup controller ID”
02 Login/logout step
The SY210NT controller needs to complete the login step to enter function menu. The
controller will automatically logout when the user stops operating about two minutes.
However, in order to confirm the door access security, please execute logout steps after
finish setting.
Login Step
Enter key LCD display Reference
MENU System
EN Login
EN Password
Wait for password enter
1+2+3+4+EN Master OK
Setup light flashes, already in login status

SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 4 -
Logout Step(in login status)
Enter key LCD Display Reference
MENU System
EN Login
▼Logout
EN Display date and time Setup light goes out, complete logout
ste
p
.
＊The below steps pre-set in login status
03 Setup Module (setup reader)
After install controller and reader, the user needs to setup reader ID and scan
communication status from controller (plug & play) to normal transmit the I/O data. The
next diagram is System main menu table and the gray part is the step operation range.

SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 5 -
Setup reader ID
Enter key LCD display Reference
MENU System
EN Login
▼＊５ System
Process
EN APBLevel
Seting
▼＊２ Change
ModuleID Modify/setup module ID item
EN Module
[READER] Use ▲▼ key to choose the installed
module type (annotate 1)
EN Serial
03150001 Enter module serial number(annotate 2)
EN ModuleID
ID = [ 1 ] Setup module ID (annotate 3)
EN Change
ModuleID Setup complete, back to item
Annotation 1: Module type
Annotation 2: The user can find the serial number sticker from card reader package or
machine back.
Annotation 3: Card reader ID arrange rule
READER General proximity reader, including SYRDS1、S5、L5。
DIDO Digital contact expand module, including MDDIDO-1S、MDDIDO-16。
PRINT Printer module
SYRDK5 Keypad proximity reader
SYRDF5 Fingerprint proximity reader
SYRDT5 LCD display card reader
Door one Door two Door three Door four
Incoming reader ID 1 ID 2 ID 3 ID 4
Outgoing reader ID 5 ID 6 ID 7 ID 8
Door
Function

SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 6 -
Scan communication from controller (plug & play)
Enter key LCD display Reference
MENU System
EN Login
▼＊３ Module
Process
EN ADD
Module
▼＊３ Module
PlugPlay Scan module communication item
EN Module
Waitting Scanning communicated module
Please wait Find：01
OK
Display communicated module
amount
(
annotate
)
CLR Module
PlugPlay Setup complete, back to item
Annotation:
The controllers will automatically display the plug & play result. In normal status, the display
module amount will match with the practical installed module amount. In another word, the
scan result should display: Find: 04 OK. If the display amount is unusual, please refer the
below table to eliminate the issue.
Unusual
situation Scan (display 00) or display less amount
Possibility The communication is not correct or repeat ID
Eliminate
method
◎Please confirm the communication again
◎The factory default of reader ID all set to “1”. The ID did not setup
properly when communicated with multiple reader or ID repeat cause
transmission conflict and can not find the module correctly.
Please contact with the Syris technical personnel if confirm the above questions but still can
not communicate correctly.

SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 7 -
04 Add/delete/ edit card
The add card function separate into (Add Card By Serial) or (Add Card By No. )
The edit card function is for setup card enable/disable (Status Setting), passage application
group (APP Setting), card password (PIN Setting) and anti-pass-back function (APB
Setting)
Delete card can separate into (Del Card by No.) or (Delete All Card). The next diagram is
the Card main menu table and the gray part is the step operation range.

SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 8 -
Add card
Enter key LCD display Reference
MENU System
▼Card
EN Add Card
Process
EN Add Card
By Serial
Automatically sort add card module
(annotate)
EN Ins Card Waiting for proximity un-gotten card
Proximity
un-used card
Ins Card
[0001]
First time enter card sort from 0001,
serial proximity new card will
automatically increase card number.
Proximity using
card
Ins Card
Card Use
If card has been used, the screen will
dis
p
la
y
su
gg
est messa
g
e
CLR Add Card
By Serial Leave automatically add card mode
Annotation:
Automatically add card function(Add Card By Serial), when user first time add card, the
card number will automatically sort from 0001 and continue to proximity un-used card, the
card number will automatically add up. If there are several cards have been deleted in one
serial card numbers, it will be fill in the card number which has been deleted first. For
example, the already add card number from 0001 to 0010 which the 0005 has been deleted
lately, and next time when user use automatically add card function, it will fill in 0005 then
start add up card number from 0011.
Add card by number function (Add Card by No.) is to add card by assign card number. To
continue last example, the card number has add to 0010, the user can directly enter card
number 0011 then add card, in the add card process, the card number will automatically
skip over the already exist card number and will not cover the original number. For example,
if card 0015 has been add in advance, when proximity to card 0014, the card number will
automatically jump to 0016.

SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 9 -
Edit Card(enable/disable)
Enter key LCD display Reference
MENU System
▼Card
EN Add Card
Process
▼Modify
One Card Edit card item
EN Card No
No:0001
Enter the card number which want to
edit
EN Status
Setting Card enable/disable setup mode
EN Card
[Enable] Card normal status is enable
▼Card
[Disabl] Set up card to disable
EN Status
Setting Card has been modified, back to item
The other function of edit card, we suggest the user co-operate with SYW95A door access
manage software to proceed setting, the description of each function is at next page:
Passage Application Group (APP Setting):
Able to setup card (holder) group (max.16 groups). Co-operate with SYW95A door access
manage software can setup the passage timer and passage door.
Card password (PIN Setting):
Install keypad proximity reader can setup card (holder) personal password, though
SYW95A door access manage software can setup open door mode to “card plus
password”.
Anti-pass-back (APB Setting):
Base on “one in one out” control idea to avoid one card repeat incoming/outgoing situation,
mostly apply to parking space management or research centre personnel management.