Syrp genie Micro GU01 User manual

Setup Guide
Micro
Model: GU01

An easy-to-use device for controlling your camera
remotely for capturing photos, time-lapses and
video. Connect the Genie Micro to your camera and
wirelessly control it from any iOS or Android device
using the Syrp App.
This Setup Guide will take you through the basics to
get you started using your Genie Micro for the
first time.
A full user manual can be found on the support
section page at www.syrp.co
Genie Micro

What’s in the Box
USB-C to USB-A Male Cable
Micro Fiber Cloth
Genie Micro
USB-C to USB-A
Female Cable

Genie Micro Interface
Charging Light
Connection Light
Camera Light
Charging Port/
USB Camera Control
On/ Off Button
Camera Port

Charging
Plug the USB cable into a wall
charger, laptop or USB port.
1
Orange light indicates
charging, green indicates
fully charged.
Plug the USB-C plug into the
Genie Micro charging port.
2
The Genie Micro can not
be charged while in use.

Mount the Genie Micro
1
Insert the Genie Micro on to the hotshoe of your
camera, with the power button facing the back of
the camera.

Shutter Control
2
1
Plug the 2.5mm end of your Shutter Link Cable (*sold
separately) into the camera port on the Genie Micro.
Plug the other end into the remote port on your
camera. Consult your camera manual to find the
correct port.
Select a Shutter link cable for
your camera at www.syrp.co
*

Device Connection
1
2
3
Turn bluetooth ON in the settings menu
on your device.
Download and open the Syrp App.
Press the power button on the Genie
Micro once to turn it on.
(Don’t hold the power button down)
Flashing LED indicates
ready to pair and solid
green indicates paired

CONNECTION
CONNECTION
App Connection
Tap the
icon
1
Select your
Genie Micro
2
CONNECTION
GENIE MICRO
Panning
CREATE CONTENT
COMMUNITY TUTORIALS

CONNECTION
XXXXX
XXX
CONNECTION
Up to date
vX.X
Firmware Update
icon appears
when device has
updated
2
Tap the
icon to update
firmware
1

www.syrp.co
twitter.com/syrp_
instagram.com/syrp_
facebook.com/syrp.co
[email protected]
youtube.com/syrpey
For tutorials on operating the Genie Micro and
navigating the App tap the question mark ? on the
home screen of the App or subscribe to our
YouTube Channel.
Learn More

Genie Micro Quick Tips
Always set your camera and lens to manual focus (MF), if
set to Auto Focus (AF) the camera can misfire, leading to
missed frames.
Turn image review OFF on your camera. On some cameras
image review can cause missed frames in your time-lapse.
Once you begin a time-lapse or video recording you can
leave the App and disconnect, your move will continue to
run as normal.
Press the power button once to turn the Genie Micro on.
To turn the Genie Micro off, hold the power button for 2
seconds.
Hold the power button down for more than 20 seconds to
force shutdown the device.

Firmware Tips
The App will alert you if a new firmware update is
available. If you have trouble updating the Firmware
try these tips:
Close the App down and restart the App.
Force the device into “factory mode” by holding down the
power button for over 10 seconds untill all 3 LED’s start
flashing. After this, retry updating the device from the App.
Note that the device’s name will have changed to
something similar to “Syrp: XXXXXXXXXXXX”.
For iOS devices, go to Settings > Cellular/Mobile Data.
Then scroll down and turn Wi-Fi Assist Off.
Try updating from a different location or device.
Visit the support section page at www.syrp.co for more
detailed help.