Syscom Video IR Bullet Network Camera User manual

Quick Installation Guide
IR Bullet
Network Camera
Please read this manual thoroughly before use, and keep it handy for future reference.

Quick Installation Guide
1. Description
The Network Camera supports the network service for a sensor image with progressive scan, which
can be monitored on a real-time screen regardless of distances and locations. By using its dedicated
program, many users are able to have an access to the Network Camera at once or a single user can
monitor various network cameras at the same time. It also enables users to play, store and retrieve a
monitoring image by using a PC. All the settings and real-time monitoring screens are also provided
through an access to the web.
The Network Camera is fully featured for security surveillance and remote monitoring needs. It is
based on the DSP compression chip, and makes it available on the network as real-time, full frame
rate Motion JPEG and H.264 (or MPEG-4) video streams.
The alarm input and alarm output can be used to connect various third party devices, such as, door
sensors and alarm bells.
• Installation Steps
Follow these steps to install the network camera on your local network (LAN):
1. Check the package contents against the list below.
2. Connect the Network Camera
3. Set an IP address.
4. Set the password.
• Package Component
The system comes with the following components:
Camera Unit Installation CD Installation Guide Accessory Kit
• Contents in the installation CD
1. The User’s Manual
2. The SmartManager User’s Manual
3. The NCTitanium User’s Manual
4. The SmartManager Installation software
5. The NCTitanium Installation software
Note: Check your package to make sure that you received the complete system, including all
components shown above.
2

Quick Installation Guide
• Connection Cable
NO Name Description
1 Power Cable Cable for Power source (DC 12V)
2 Ethernet Cable Cable for Ethernet (POE)
Camera Dimension
See the diagrams below for the exact dimension
Dimensions Unit: mm
Base Installation(Cable through the wall or ceiling with the mount base)
Secure the camera to the wall or ceiling by the camera stand (individual purchase).
Ceiling Mount W all Mount
3

Quick Installation Guide
2. Installation
2.1 Connection
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the network camera. Generally a
cross-over cable is used for directly connection to PC, while a direct cable is used for connection
to a hub.
Micro SD memory slot
Remove the front cap of the camera to insert the SD memory card.
SD memory card slot
Remove the front cap
• Connecting the Power
Connect the DC 12V power adaptor to the camera.
4

Quick Installation Guide
2.2 Network Connection and IP assignment
The Network Camera supports the operation through the network. When a camera is first connected
to the network it has no IP address. So, it is necessary to allocate an IP address to the device with the
“Smart Manager” utility on the CD. The factory default IP is “192.168.30.220”.
1. Connect the Network Camera / device to the network and power up.
2. Start SmartManager utility (Start>All programs>SmartManager>SmartManager), the main
window will be displayed, after a short while any network devices connected to the network will
be displayed in the list.
3. Select the camera on the list and click right button of the mouse. You can see the pop-up menu
below.
4. Select Assign IP. You cam see a Assign IP window. Enter the required IP address.
Note: For more information, refer to the Smart Manger User’s Manual.
5

2.3 Basic Configuration of Dome Camera System
No. Wire Color Description
1Red: 12VDC+
White: 12VDC- Main Power: 2pin terminal
2Pink, Brown Heater Power(Option): 3pin terminal
3
Black: GND
Gray: Alarm Input
Yellow: GND
Black&White: Alarm Output
Green: RS485+
Blue: RS485-
Alarm Input/Output, RS485: 6pin terminal
4Black Ethernet: RJ45 Modular Jack
5Yellow Video Composite Output: BNC Jack
6Red Audio line output: RCA Jack
7White Audio line input: RCA Jack
The dome camera must be installed by qualified service personnel in accordance with all local
and federal electrical and building codes.
6

2.4 Setting Dome Camera Address (ID)
To prevent damage, each dome camera must have a unique address (ID).
When installing multiple dome cameras using a multiplexer, it is suggested that the dome camera
address match the multiplexer port number.
The factory default setting is 1.
2.5 Connections
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the dome camera. Generally a cross-
over cable is used for directly connection to PC, while a direct cable is used for connection to a
hub.
• Connecting Alarms
AI (Alarm Input)
You can use external devices to signal the dome camera to react on events. Mechanical or
electrical switches can be wired to the AI (Alarm Input) and G (Ground) connectors.
G (Ground)
NOTE: All the connectors marked G or GND are common.
Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.
AO (Alarm Output)
The dome camera can activate external devices such as buzzers or lights. Connect the device
to the AO (Alarm Output) and G (Ground) connectors.
• Connecting to the RS485
The dome camera can be controlled remotely by an external device or control system, such as
a control keyboard, using RS485 half-duplex serial communications signals.
• Connecting Video out connector
Connect the video out (BNC) connector to the monitor or video input.
• Connecting the Power
Connect the power of 12VDC 1.0A for the dome camera.
When using a 12VDC adapter, connector the positive(+) pole to the ‘+’ position and the
negative(-) pole to the ‘-‘ position.
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.
7

2.6 IP Assignment
When the dome camera, encoder or decoder is first connected to the network it has no IP
address. So, it is necessary to allocate an IP address to the device with the “SmartManager”
utility on the CD.
1. Connect the dome camera / device to the network and power up.
2. Start SmartManager utility (Start > All programs > SmartManager > SmartManager), the main
window will be displayed, after a short while any network devices connected to the network will
be displayed in the list.
3. Select the dome camera on the list and click right button of the mouse.
You can see the pop-up menu as below.
4. Select Assign IP Address. You can see Assign IP window. Enter the required IP address.
Note: For more information, refer to the SmartManager User’s Manual.
8

2.7 Getting Started
Once installed apply power to the dome camera. The dome camera will start a configuration
sequence.
OSD Position
The dome can move the OSD position in the OSD position setup.
(AREA TITLE) (AF AE)
(FUNC TITLE )
(CTRL KEY TO MOVE)
SAVE AND EXIT(ESC TO CANCEL)
(DOME ID…)
(ANGLE…)
OSD Position Setup
001 AF AE
EMPTY DATA
DOMEID:001
W→360.0 090.0
INFORMATION
DISPLAY
PRESET TITLE
A
REA TITLE
FUNCTION
UNDER RUNNING
CAMERA TITLE
CAMERA ID
VIEW DIRECTION
PAN & TILT ANGLE
STATUS of
FOCUS and AE
9

Chapter 3 — Program and Operation
3.1 Dome Camera Selection
Before you program or operate a dome camera, you must select the dome camera by pressing
No. + CAM keys.
Example:Pressing 1, 0+ CAM keys sequentially will select dome camera 10. The selected
dome camera ID will be displayed on the LCD monitor of the keyboard controller.
3.2 Accessing the On-Screen Menu Utility
You can call up the On-screen menu utility on your monitor by pressing the MENU key on the
keyboard controller, the following On-screen menu utility will appear:
DOME MENU
AUTO SCAN
PRESET
TOUR
PATTERN
AREA TITLE
PRIVACY ZONE
CAMERA
DOME SETUP
DOME COMMUNICATION
FUNCTION RUN
EXIT(ESC TO EXIT)
3.3 How to control the On-Screen Menu Utility
Function Button
Call the On-screen menu utility. MENU
Navigate through the menu items. Joystick up or down
Go into the sub-menu items. Joystick left or right or IRIS Open
Change value.
Enter the editing title mode.
Joystick left or right or
Zoom handle twist or Tele , Wide
Change value of angle. CTRL + Joystick
Enter the changing angle mode. IRIS Open
Exit the changing angle mode. IRIS Close
Escape (EXIT) ESC
10

Chapter 4 — Operation by Web Browser
The network camera can be used with Windows operating system and browsers.
The recommended browsers are Internet Explorer, Safari, Firefox, Opera and Google Chrome
with Windows.
Note: To view streaming video in Microsoft Internet Explorer, set your browser to allow ActiveX
controls.
4.1 Access from a browser
1) Start a browser (Internet Explorer).
2) Enter the IP address or host name of the network camera in the Location/Address field of
your browser.
3) You can see a starting page. Click Live View or Setup to enter web page.
4) The encoder’s Live View page appears in your browser.
11

4.2 Access from the internet
Access from the internet once connected, the network camera is accessible on your local
network (LAN). To access the video encoder from the Internet you must configure your
broadband router to allow incoming data traffic to the video encoder. To do this, enable the NAT
traversal feature, which will attempt to automatically configure the router to allow access to the
video encoder. This is enabled from Setup > System > Network > NAT Traversal.
4.3 Setting the admin password over a secure connection
To gain access to the product, the password for the default administrator user must be set. This
is done in the “Admin Password” dialog, which is displayed when the network camera is
accessed for the setup at the first time. Enter your admin name and password, set by the
administrator.
Note: The default administrator username and password is “admin”. If the password is lost, the
network camera must be reset to the factory default settings.
To prevent network eavesdropping when setting the admin password, this can be done via an
encrypted HTTPS connection, which requires an HTTPS certificate (see note below).
To set the password via a standard HTTP connection, enter it directly in the first dialog shown
below. To set the password via an encrypted HTTPS connection, please see Setup > System >
Security > HTTPS.
Note: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic
between web browsers and servers. The HTTPS certificate controls the encrypted
exchange of information.
4.4 Live View Page
The live view page comes in seven screen modes like 704x576(480), 704x288(240),
352x288(240), 176x144(120), 640x480, 320x240 and 160x120. Users are allowed to select the
most suitable one out of those modes. Please, adjust the mode in accordance with your PC
specifications and monitoring purposes.
12

1) General controls
The video drop-down list allows you to select a customized or pre-
programmed video stream on the live view page. Stream profiles are
configured under Setup > Basic Configuration > Video & Image.
The resolution drop-down list allows you to select the most suitable one
out of video resolutions to be displayed on live view page.
The protocol drop-down list allows you to select which combination of
protocols and methods to use depends on your viewing requirements, and
on the properties of your network.
The preset drop-down list allows you to select the preset number for the
PTZ camera being used. This icon is inactivated if the PTZ settings are not
set.
2) Control toolbar
The live viewer toolbar is available in the web browser page only. It displays the following
buttons:
The Stop button stops the video stream being played. Pressing the key again toggles
the start and stop. The Start button connects to the network camera or start playing a
video stream.
The Pause button pause the video stream being played.
The Snapshot button takes a snapshot of the current image. The location where the
image is saved can be specified.
The digital zoom activates a zoom-in or zoom-out function for video image on the live
screen.
The Full Screen button causes the video image to fill the entire screen area. No other
windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full
screen view.
The Manual Trigger button activates a pop-up window to manually start or stop the
event.
The Camera Menu button activates a pop-up window for camera menu control.
The PTZ button activates a pop-up window for Pan, Tilt and Zoom control.
13

Use this scale to control the volume of the speakers.
Use this scale to control the volume of the microphone.
Use this scale to control the volume of the speakers and microphones.
3) Camera Menu controls
If the network camera has been appropriately configured, the Live View page displays the
controls available for the OSD menu.
4) Pan/Tilt/Zoom controls
If the network camera has been appropriately configured, the Live View page displays the
controls available for the PTZ (Pan Tilt Zoom) or PT device installed. The administrator can
enable/disable the controls for specified users.
5) Video and Audio Streams
The network camera provides several images and video stream formats. Your requirements
and the properties of your network will determine the type you use.
The Live View page in the network camera provides access to H.264, MPEG-4 and Motion
JPEG video streams, and to the list of available video streams. Other applications and
clients can also access these video streams/images directly, without going via the Live View
page.
4.5 Network Camera Setup
This section describes how to configure the network camera, and is intended for product
Administrators, who have unrestricted access to all the Setup tools; and Operators, who have
access to the settings for Basic, Live View, Video & Image, Audio, Event, and System
Configuration.
You can configure the network camera by clicking Setup in the top right-hand corner of the Live
View page. Click on this page to access the online help that explains the setup tools.
When accessing the network camera for the first time, the “Admin Password” dialog appears.
Enter your admin name and password, set by the administrator.
Note: If the password is lost, the network camera must be reset to the factory default settings.
14

15
4.6 Resetting to the factory default settings
To reset the network camera to the original factory settings, go to the Setup > System >
Maintenance web page or use the control button on the network camera, as described below:
• Using the Reset Button
Follow the instructions below to reset the network camera to the factory default settings
using the Reset Button.
1. Switch off the network camera by disconnecting the power adapter.
2. Open the lens cover.
3. Press and hold the Control Button (SW1) on the board with your finger while reconnecting
the power.
4. Keep the Control button (SW1) pressed during about 2 seconds.
5. Release the Control Button (SW1).
6. The network camera resets to factory defaults and restarts after completing the factory
reset.
7. Close the lens cover.
CAUTION: When performing a Factory Reset, you will lose any settings you have saved.
4.7 System Requirement for Web Browser
Operating System: Microsoft Windows 98, Microsoft Windows ME, Microsoft Windows 2000,
Microsoft Windows XP, or Microsoft Windows Vista
CPU: Over Pentium IV 2.4Ghz, 512MB RAM, 10GB free disk or higher
VGA: AGP, Video RAM 32MB or higher (1024x768, 24bpp or higher)
4.8 More Information
For more information, please see the Network Camera User’s Manual, which is available on the
CD included in this package.

22X PTZ III NETWORK DOME CAMERA
Printed in Korea 50302800B