tae DMI 2000 Parts list manual

Instrucon and Operang Manual
Cauon :
As with any form of electrical equipment, there is always a risk involved in the handling of electrical
machinery. The greatest care must always be exercised during installation and maintenance, and it is
recommended this be carried out by authorized personnel.
Voltmeter
DMI 2000
m/min
TAE Antriebstechnik • Raiffeisenstraße 10 • D-61250 Usingen
The German text applies in cases of doubt

2
BA VOL2000-e.PDF PT Stand 28.09.2012 Änd.-Nr. 00002
Misprints and technical changes reserved
Voltmeter
1.0 Technical data
2.0 Connecon and Design
Supply voltage: 230V 50/60 Hz or 24VDC (other voltages on request)
Max. power consumption: 3VA
Display: 14mm 7-Segment LED-rot
Decimal point: programable with jumper (external)
Meßeingang: 0-20 VDC or 0-500VDC
Display: A, m/min, m, UPM, %, L/sec (other on request)
Anschlußart: Screw terminals (back side)
Weight: 275g
number of digits
2,5 3,0 3,5 4,0
Fault
deviation: 1% 1% 0,1% 0,1%
Max.
display: 199 999 1999 9990
12345678
I
II
III
IV
V
VI
NL
Measuring
Input
Decimal point
preset
Supply
voltage
Fuse 0,5A
Jumper
Supply voltage 230VAC Supply voltage 24VDC
Measuring
Input
Decimal point
preset
0-20V
Supply
voltage
24VDC
0VDC
R17
R15
R14
Potentiometer
Jumpers
Supply
voltage
230VAC R4 R5 R16
24VDC R15 R14 R17
Measuring
input
20VDC 5k6 33k 100k
500VDC 180k 180k 10k

3
BA VOL2000-e.PDF PT Stand 28.09.2012 Änd.-Nr. 00002
Misprints and technical changes reserved
Voltmeter
3.0 Adjustment of the DMI 2000
I
II
III
IV
V
VI
fully ccw
I- V
oen
Volt DC
fully clockwise
20 500 20 500
fully ccw fully clockwise
20 500 20 500
Display 199 and 1999 999 and 9990
Input voltage by 199,1999, 999 und 9990
all values in volt
58
Potenometer adjustment
Jumpers
671 21 248 60 627 21,7 228
31 388 12 145 33,9 368 12,2 132,6
19 238 6,9 89 19,55 224 7,04 81
11 151 4,2 56 11,4 143 4,1 51,5
7,1 101 2,7 38 6,74 96 2,4 34,6
4,2 66 1,6 25 3,45 63 1,25 22,7
2,7 47 1,1 18 1,66 44,9 0,6 16,2
By using a DMI-2000 with a display 999 and 9990 please note that the input voltage may not exceed the adjusted range, because
in this case the display starts with 0 again.
4.0 Seng the decimal point
12345678
Terminals
Jumper
Display
12345678
Terminals
Jumper
Display
12345678
Terminals
Jumper
Display

4
BA VOL2000-e.PDF PT Stand 28.09.2012 Änd.-Nr. 00002
Misprints and technical changes reserved
5.0 Dimensions
All dimensions in millimeters
Voltmeter