Taga Harmony PC Series User manual

PC Series [230V]
POWER LINE CONDITIONER
FOR USE WITH AUDIO-VIDEO EQUIPMENT
Instruction Manual
Edition 03-2020

2
Introduction
Thank you for purchasing this TAGA Harmony power line conditioner.
The electricity network in our homes or workplaces is exposed to di󰀨erent interferences
for instance electromagnetic interference (EMI) generated by appliances connected to
the same network (refrigerators, air conditioners, computers etc.). These interferences
are not only produced inside your house or o󰀩ce but by all appliances in your building
or even outside it and can di󰀨er on the time of day or week when the tra󰀩c on the
electrical network changes.
All these interferences which we call noises can get into your AC power and interfere
with your system.
This “dirty” electricity can have a negative e󰀨ect on performance of your audio-video
system.
TAGA Harmony power line conditioner is a next level, e󰀨ective and reliable protection
against voltage uctuations and line disturbances (noises) which can negatively impact
your audio-video system.
Thanks to our PC power line conditioners you will be able to enjoy a better quality of
your audio and video equipment.
The contaminated electricity has also a negative impact on internal circuits and power
supplies of your equipment and because the PC conditioner works as a bu󰀨er between
the wall socket and your gear it will help to increase the longevity of the connected
components.
Features:
• Independent groups of switched and unswitched power sockets (Schuko type)
specically designed for use with di󰀨erent audio and video equipment.
• Voltage meter (selected models) to control stability of the power voltage in the wall
outlet.
• Phase detection indicates the incorrect power phase and the Polarity Switch allows
to easily correct it.
• Diversied duplex ltering based on a high-quality Class-X capacitors and
inductors.
• High power toroidal transformer to isolate equipment from the line noise.
• Spike and surge protection to protect against everyday high energy spikes
and transient voltages.
• Primary lightning surge protection to protect of the load equipment from e󰀨ects of
high transient over-voltages following a lightning strike (introduced indirectly into the
utility mains).
• Removable IEC type power cord gives an option to upgrade your system with a
premium audiophile power cable in any time.
Cleaning
Do not use strong or abrasive cleaners. Use a dry, soft cloth for cleaning.
Specications
Full technical specications are available on the www.TagaHarmony.com website.

3
Contents
Safety Instructions 4
Controls and display 6
Hooking Up the Conditioner and Operation 7
Kit Content 11

4
Safety Instructions
IMPORTANT
READ THIS SECTION CAREFULLY BEFORE PROCEEDING!
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPARATUS TO RAIN OR MOISTURE, AND OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS.
CAUTION: TO PREVENT ELECTRIC SHOCK, FULLY AND SECURELY INSERT
THE POWER CABLE PLUG INTO THE POWER OUTLET, AND POWER CABLE
CONNECTOR INTO THE UNIT SOCKET (IF THIS UNIT IS NOT EQUIPPED WITH AN
INTEGRATED [ATTACHED] POWER CORD).
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE
THE FUSE (IF THE UNIT IS EQUIPPED WITH A USER REPLACEABLE FUSE) ONLY
WITH THE SAME AMPERAGE AND VOLTAGE TYPE. IN CASE WHEN THE UNIT IS
NOT EQUIPPED WITH A USER REPLACEABLE FUSE - REFER REPLACEMENT TO
QUALIFIED SERVICE PERSONNEL.
WARNING: THE UNIT MAY BECOME HOT. ALWAYS PROVIDE ADEQUATE
VENTILATION TO ALLOW FOR COOLING. DO NOT PLACE THE UNIT NEAR
A HEAT SOURCE, OR IN SPACES THAT CAN RESTRICT VENTILATION.
An exclamation mark in a triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
The triangle containing a lightning symbol is intended to alert the user to the presence
of uninsulated dangerous voltages within the product’s enclosure that may be of
su󰀩cient magnitude to constitute a risk of electric shock to persons.
EN_safety_02-20_1

5
Safety Instructions
1. Read Instructions - All the safety and operating instructions
should be read before the product is operated.
2. Retain Instructions - The safety and operating instructions should
be retained for future reference.
3. Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should
be followed.
5. Cleaning - Unplug this product from the power outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
6. Water and Moisture - Do not use this product near water - for
example, near a bath tub, wash bowl, kitchen sink or laundry tub;
in a wet basement; or near a swimming pool; and the like. These
precautions also apply to the power cord.
7. Accessories - Do not place this product on an unstable cart,
stand, tripod, bracket or table. The product may fall, causing seri-
ous injury to a child or adult and serious damage to the product.
Use only with a cart, stand, tripod, bracket or table recommended
by the manufacturer or sold with the product. Any mounting of
the product should follow manufacturer’s instructions and should
use a mounting accessory recommended by the manufacturer.
8. Ventilation - This unit may be equipped with slots and openings
in the cabinet (housing) which are provided for ventilation and
to ensure reliable operation of the product and to protect it from
overheating and these openings must not be blocked or covered.
The openings should never be blocked by placing the product
on a bed, sofa, rug or other similar surface. This product should
be not placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to. For products equipped with a
separate power supply unit, leave at least 5cm (2in.) of free space
on all sides and the top of the power supply.
9. Power Sources - This product should be operated only from the
type of power source indicated on the marking label (placed on
the product and/or, if applicable, on a separate power supply
unit). If you are not sure of the type of power supply in your home,
consult your product dealer or local power company. For products
intended to operate from battery power or other sources, refer to
the operating instructions.
10. Grounding and Polarity - some units for proper operation or
to take full advantage of their capabilities may require to be
connected to a grounded power outlet – refer to the user manual
for more information.
Some units may have markings for the live (L) and neutral (N)
conductors for power - in order to take full advantage of capa-
bilities of such products, it is recommended to properly connect
the polarity according to the markings on the unit - refer to the
user manual for more information. Connecting the polarity not in
accordance with the markings will not aect the durability and
reliability of the device.
11. Power-cord Protection - Power supply cords should be routed
so that the are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles and the point where they exit
from the product.
12. Lighting - For added protection for this product during a lighting
storm or when it is left unattended and unused for long periods
of time, unplug it from the wall outlet and disconnect the antenna
or system cables. This will prevent damage to the product due to
lighting and power-line surges.
13. Overloading - Do not overload wall outlets, extension cords or
integral convenience receptacles as this can result in a risk of fire
or electric shock.
14. Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric
shock. Do not expose this apparatus to dripping or splashing and
ensure that no objects filled with water, such as vases are placed
on the apparatus.
15. Servicing - Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service
personnel.
16. Damage Requiring Service - Unplug this product from wall outlet
and refer servicing to qualified personnel under the following
conditions:
• when power supply cord or plug is damaged;
• if liquid has been spilled or objects have fallen into the product;
• if the product does not operate normally by following the oper-
ating instructions. Adjust only those controls that are covered by
the operating instructions as an improper adjustment of other
controls may result in damage and will require extensive work
by a qualified technician to restore the product to its normal
operation;
• if the product has been dropped or damaged in any way;
• if the product exhibits a distinct change in performance - this
indicates a need for a service.
1 7. Replacement Parts - when replacement parts are required, be
sure the technician has used replacement parts specified by the
manufacturer or with the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock
or other hazards.
18. Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety check to
determine that the products is in proper operating condition.
19. Wall of ceiling mounting - The product should be mounted to a
wall or ceiling only as recommended by the manufacturer.
20. Heat - The product should be situated away from heat sources
such as radiators, heat registers, stoves or other products (includ-
ing amplifiers) that produce heat.
21. [Refer to products equipped with vacuum tubes] Tube Cage or
cover - For your safety and to protect the vacuum tubes this
product may be equipped with the factory installed vacuum tube
cage or cover.
It is not recommended to remove the cage or cover unless it is
required to change the vacuum tubes.
When the cage or cover is removed - do not touch the vacuum
tubes - they may be hot and burn the skin!
22. Operating Environment - Operating environment temperature and
humidity of the unit: +5°C to +35°C (+41°F to +95°F); less than
85% RH (cooling slots not blocked).
EN_safety_02-20_1

6
Controls and Displays
45
PC-5000
SWITCHE D
Gro up II (1A m ax)
UNSWITCHED
L
N
L
N
L
N
L
N
NL NL
Gro up I (3A ma x)
Gro up IV (5A m ax)
NLNL
Gro up III (5 A m ax)
9
FRONT
1.Power Switch (ON and OFF)
2.Power Indicator
3.Phase Indicator
4.Voltage Meter Display
REAR
5.Power Cable Input and Fuse Box
6.Fuse Box
7.Ground Screw
8.Polarity Switch
/PC-5000 model shown/
3
2
16
8
7
10
Never operate this switch when the conditioner is connected to the
electrical outlet – this may damage the conditioner and/or connected
devices – this may void your warranty.
Make sure to disconnect the Power Cable before operating the Polarity
Switch!
A blown fuse should be only exchanged for exactly the same type as
indicated on the rear conditioner panel above the Fuse Box.
The Power Cable should be disconnected!
A blown fuse should be only exchanged for exactly the same type as
indicated on the rear amplier panel above the Power Cable Input.
The Power Cable should be disconnected!

7
1.Phase Detection
A. Make sure that the Polarity Switch is set as 1 (default). It means that the female
contacts in the Power Sockets have polarity according to the L and N marking on
the top panel of the conditioner.
B. Without connecting any external equipment plug the Power Cable to the
conditioner and into the electrical outlet.
C. The Phase Indicator WILL ILLUMINATE when the phase is INCORRECT.
If the phase is incorrect then:
d1- Remove the Power Cable from the electrical outlet;
d2- Set the Polarity Switch to 2;
d3- Connect the Power Cable to the electrical outlet;
d4- The Phase Indicator should not be illuminated - it means that the phase is
correct.
D. If your audio-video equipment has the polarity marking (L/N) make sure to connect
correctly the equipment power cable plug to the power line conditioner according
to the polarity marking.
Hooking Up the Conditioner and Operation
The Phase Detection is not related to the Power Switch and is always
active when the conditioner is connected to the electrical outlet.
TOP
9. Switched Power Sockets
Group I recommended for digital equipment.
Group II recommended for sound sources.
10. Unswitched Power Sockets
Group III recommended for preampliers / accessories.
Group IV recommended for ampliers.
Never operate this switch when the conditioner is connected to the
electrical outlet – this may damage the conditioner and/or connected
devices – this may void your warranty.
Make sure to disconnect the Power Cable before operating the Polarity
Switch!
Setting the Polarity Switch to 2 will exchange the polarity in the Power
Sockets of the conditioner (L → N and N → L).
Make sure to consider this when connecting the external equipment.

8
Hooking Up the Conditioner and Operation
PC-5000
SWIT CHE D
Grou p II (1A max )
UNSWITCHED
L
N
L
N
L
N
L
N
NL NL
Grou p I (3A max)
Grou p IV (5A max )
NLNL
Grou p III (5A ma x)
Group I
Group II
Sound Sources
CD/DVD/Blu-ray Player, Turntable,
Radio Tuner
Digital Equipment
DAC, Music Streamer,
Media Player, BT receiver
PC-5000
SWIT CHE D
Grou p II (1A max )
UNSWITCHED
L
N
L
N
L
N
L
N
NL NL
Grou p I (3A max)
Grou p IV (5A max )
NLNL
Grou p III (5A ma x)
Group III
Preampliers & Accessories
Preamplier, Phono Stage,
Headphone Amplier
PC-5000
SWIT CHE D
Grou p II (1A max )
UNSWITCHED
L
N
L
N
L
N
L
N
NL NL
Grou p I (3A max)
Grou p IV (5A max )
NLNL
Grou p III (5A ma x)
Group IV
Ampliers
Power Amplier,Solid State / Hybrid /
Tube Integrated Ampliers,
AV Receiver
PC-5000
SWIT CHE D
Grou p II (1A max )
UNSWITCHED
L
N
L
N
L
N
L
N
NL NL
Grou p I (3A max)
Grou p IV (5A max )
NLNL
Grou p III (5A ma x)
Power cable
Power cable
Power cable
Power cable

9
Hooking Up the Conditioner and Operation
2. Make sure the conditioner is turned o󰀨 (the Power Switch is in the down OFF position and the
Power Cable is removed).
3. Using power cables (only a power cable for the conditioner is supplied with this product)
connect your audio-video equipment to the Power Sockets following the Phase Detection
recommendations.
Follow the below recommendations for connections:
SWITCHED POWER SOCKETS
These sockets are controlled by the Power Switch and are only operating while the Power Switch
is in the 1 (ON) position.
Group I [low-power inductance ltering] of Power Sockets is recommended for digital equipment
[DAC, Music Streamer, Media Player, BT receiver].
Group II [low-power inductance ltering, isolated by the power transformer] of Power Sockets is
recommended for sound sources [CD/DVD/Blu-ray Player, Turntable, Radio Tuner].
Note! Group II is specially designed for sound sources. Do not connect other equipment to the
Power Sockets in this group.
UNSWITCHED POWER SOCKETS
These sockets are not controlled by the Power Switch and are powered whenever the conditioner
is connected to the electrical outlet.
Group III [high-power inductance ltering] of Power Sockets is recommended for preampliers /
accessories [Preamplier, Phono Stage, Headphone Amplier].
Group IV [high-power inductance ltering] of Power Sockets is recommended for ampliers
[Power Amplier, Solid State / Hybrid / Tube Integrated Ampliers, AV Receiver].

10
Hooking Up the Conditioner and Operation
4. Grounding is recommended for this conditioner. Using a solid, insulated cable (not supplied with
this product) connect the Ground Screw with the ground source in a room.
5. Your conditioner is ready for operation.
6. Plug the Power Cable to the conditioner and into the electrical outlet.
7. Whenever the power line conditioner is connected to the electrical outlet which is properly
working the Voltage Meter will be displaying approximate current voltage in Volts.
Note! The results of Voltage Meter measurement accuracy are highly approximate and should
not be taken into account for the professional assessment of the power line quality.
8. Turn on the conditioner (the Power Switch should be in the upper ON position). It is not required
if you want to use audio-video equipment connected to the Unswitched Power Sockets.
9. Turn on your audio-video equipment and enjoy your system.
IMPORTANT SAFETY REMARKS!
• This unit requires a single-phase 3-conductor electrical outlet.
• We recommend to use Schuko plugs in all power cables.
• Make sure not to overload the power line conditioner and individual groups
of Power Sockets.
Power load for each group of Power Sockets: the total maximum power
consumption for all connected devices to a given group should not exceed
the maximum power load for this group.
The maximum load for each group is given in Amperes (A) in a bracket following
the group number printed on the conditioner: it is also available
in the specications on www.TagaHarmony.com
Total maximum power load: the total maximum power consumption for all
connected devices to the conditioner should not exceed the maximum power
load for this conditioner.
The total maximum power load for this conditioner is given in Kilowatts (kW)
or Watts (W) on the rear panel of the conditioner : it is also available
in the specications on www.TagaHarmony.com
• When you want to turn o󰀨 the power line conditioner we recommend
to turn o󰀨 your audio-video equipment rstly.
• This power line conditioner is not a uninterruptible power supply unit (UPS).
It will not operate when the input power source fails (no power or too low
voltage).

www.TagaHarmony.com
We strongly advise to contact a professional installer or dealer in order to install
TAGA Harmony products.
We recommend using high quality TAGA Harmony cables and other installation
accessories.
TAGA EUROPE
POLPAK POLAND Sp. z o.o.
AL.JEROZOLIMSKIE 331A
05-816 REGUŁY k/WARSZAWY, POLAND
Email: [e-mail]
IMPORTANT!
Your product is marked with the symbol as showed on the left.
For EU (European Union) member users:
According to the WEEE (Waste electrical and electronic equipment)
Directive, do not dispose of this product as household waste or commercial waste.
Waste electrical and electronic equipement should be appropriately collected and
recycled as required by practices established for your country.
For information on recycling of this product, please contact your local authorities, your
household waste disposal service or the shop where you purchased the product.
Your product is marked with the symbol as showed on the left.
For EU (European Union) member users:
This product has been tested and found in compliance with
requirements of the European Community
2014/30/EU (EMC) & 2014/35/EU (LVD) directives.
Kit Content:
Powe Line Conditioner 1EA
Power Cable 1EA
Instruction Manual 1EA

12
Note