Taiden HCS-3316HDB User manual

HCS-3316HDB Videoconference Camera
Installation and Operating Manual
V1.1
Excellent solutions for conferences

1
Safeguard
1. Before installing the camera, please read this manual carefully,
please follow this manual during installation and operation, and
keep it manual for future use.
2. Before powering up the camera, please check the local power
supply; make sure it complies with the requirements of the camera
power adapter.
3. During installation, please settle the cables (power/video/control)
into the right position, not to be stressed by heavy load. Don’t place
other objects over the power connection; make sure that cable
connections are well-protected and well-contacted.
4. Please operate the camera within a temperature and a humidity
range as described in this manual (operating temperature/humidity:
0℃ to 50℃(32℉to 122℉) /0 to 95%). Avoid heavy pressure,
strenuous vibration and soaking during transportation, storage and
installation.
5. Don’t disassemble the camera by yourself, please turn to
professional and qualified personnel for help when necessary.
6. Hold the bottom of the camera when installing, do not touch very
easily damageable parts.
7. Video and control cables should be well-shielded to keep stable
signal transmission.
8. When cleaning the camera, please use soft cloth. If the camera is
very dirty, wipe it off gently with a soft cloth moistened with a weak
solution of water and a neutral kitchen detergent. Wring all excess
liquid from the cloth before wiping the camera. Next, wipe off all
remaining solution with a soft, dry cloth. Use lens cleaning paper to
clean the lens.

2
Contents
1. Overview ................................................................................................3
1.1 Introduction.......................................................................................3
1.2 Features ...........................................................................................4
1.3 Specifications ...................................................................................6
1.4 Structure ...........................................................................................8
2. Camera Installation ..............................................................................10
2.1 Matters Needing Attention ..............................................................10
2.2 Installation ...................................................................................... 11
3. Camera Video Out Mode .....................................................................12
3.1 Switch Configuration ......................................................................12
3.2 Format Configuration......................................................................14
4. Remote Control ....................................................................................16
5. Menu Function .....................................................................................19
5.1 Remote Control Menu ....................................................................19
5.2 Menu Item.......................................................................................20
6. Presets Description ..............................................................................23
7. RS Control............................................................................................25
7.1 Switch Configuration ......................................................................25
7.2 Menu Configuration ........................................................................26
7.3 Control Cables................................................................................27
7.4 Control Mode..................................................................................28
7.5 Connection .....................................................................................29
8. Dimensions...........................................................................................30
9. Product and Accessories......................................................................31
10. Troubleshooting..................................................................................33

3
1. Overview
1.1 Introduction
This high-definition, all-in-one, Pan/Tilt/Zoom (PTZ) Video Camera
brings the HD scenes to your life. This unique camera is equipped with a
DVI-I interface designed to maximize high video quality displays and is
capable of displaying both digital and analog signals (output options are
Y/Pb/Pr, HDMI, DVI-D, VGA, RGBHV and HD-SDI, etc.). It utilizes a
direct drive motor mechanism for achieving high-speed, quiet and
smooth P/T/Z operations. The camera covers a wide shooting range,
with a pan angle of -150° to +150°, with a max pan speed of 300°/s, tilt
angle of -30° to +90°, with a max tilt speed of 125°/s.
This unique camera employs a 1/2.7-type HD CMOS image sensor with
five mega effective pixels and can be used in combination with any
number of codecs and other systems to produce high-quality,
high-resolution images. With its wide field of view, built-in 20x optical
zoom lens, 16:9 aspect ratio video and high-speed, quiet pan/tilt
operation, the camera can cover subjects across wider space with
minimal disturbance. Combining convenient features such as auto
focus/ auto exposure, 64-position presets, auto cruise, configurable
scan mode, remote control, and external control by standard
RS-485/232 interface, it is ideal for application including
videoconferencing, distance learning, corporate training, etc.

4
1.2 Features
Features Benefit
Superb Picture Quality 5 Mega
Pixels HD CMOS Sensor
The camera incorporates a 1/2.7-type HD CMOS
sensor (a total of five mega effective pixels)
providing outstanding picture quality and high
resolution images.
Video Format Compatible with
Multiple Formats from
NTSC/PAL to Full HD
The camera allows for HD 720p to 1080p60
migration. It enables you to shoot an image
using the 1080p full high definition video format
and output in one of video formats (e.g. 720p,
1080p, 1080i and HD-analog and HD-digital).
Quiet, High-Speed Pan/Tilt
Action
By adopting the direct drive motor mechanism
similar to the drive motor found in the camera,
the camera is extremely quiet and moves
smoothly and quickly to the designated
positions.
DVI-I Interface
The camera is equipped with a DVI-I interface
designed to maximize high video quality displays
and is capable of displaying both digital and
analog signals (output is selectable from
Y/Pb/Pr, HDMI, DVI-D, VGA, and RGBHV).
High-Quality Image
Transmission via the Digital
Interface (HD-SDI)
This new camera outputs an HD image that
conforms to the SMPTE 292M serial digital
interface standard which allows a long distance
transmission of high-quality images.
Built-in Conversion Lens for
Wide Angle View
The camera incorporates a newly developed
wide-angle lens for wide field of view image
capture.

5
Features Benefit
RS-485/422 and RS-232 Serial
Control by PELCO-D/VISCA
Protocol
All camera settings and pan/tilt/zoom functions
for the camera can be controlled remotely via
PC.
240x Zoom Ratio(20x Optical +
12x Digital)
The fast and stable auto-focus zoom lens on the
camera has an impressive 240x zoom ratio.

6
1.3 Specifications
Items Specifications
Image Sensor 1/2.7-type HD CMOS sensor, 5 mega pixels
Signal System
HD: 1080p60/1080p50/1080p30/1080p25/1080i60/
1080i50/720p60/720p50/720p30/720p25;
SD: NTSC, PAL
Lens 20x optical zoom lens,
f=4.7-94mm, Fw/1.6-Ft/3.5
Zoom ratio 20x optical zoom, 12x digital zoom
Minimum object distance 0.5m (wide) - 1.5m (tele)
Horizontal viewing angel 58.7° (wide) - 3.2° (tele)
Focus Auto / Manual / One-push
Minimum Illumination 0.5Lx (50IRE, F1.6)
Exposure Auto / Manual / Shutter prioirty /
Iris priority / Exposure control
Shutter speed 1/60 to 1/10,000s (60 Hz)
1/50 to 1/10,000s (50 Hz)
Gain Auto / Manual
White balance Manual / Outdoor / Indoor1 / Indoor2 / Indoor3 /
Indoor4 / Auto / One-push
Video effect Backlight compestaion, vertical flip
OSD Menu English / Simplified chinese / Traditional chinese
S/N ratio ＞50dB
Synchronization Internal
Backlight Compensation On / Off
Pan/Tilt Speed Pan: 0.1°～200°/sec, Tilt: 0.1°～150°/sec
Pan/Tilt range Pan: ±150°, Tilt: -30°～90°
Preset 64
Video Output
HD: HD-SDI, DVI-I (is selectable from Y/Pb/Pr,
HDMI, DVI-D, VGA, RGBHV)
SD: CVBS

7
Items Specifications
Multiple video output 3-ways HD and 1-way SD
Control Protocol PELCO-D, VISCA
Control Interface RS-485/422, RS-232
Baud Rate 2400/4800/9600/19200/38400 bps
Address 0～255
Temperature Operating temperature: 0℃～+50℃
Storage temperature: -20℃～+70℃
Relative Humidity 0～95% (not condensing)
Power Requirements DC 12 V
Power Consumption <10 W
Dimensions (mm) 144(H)×259(W)×166(D)

8
1.4 Structure
Note: for HD-SDI interface (HD), the maximum transmission distance is 100 meters.
Pin assignment of RS-232

9
Pin assignment of RS-485/422
No Pin
Corresponding pin
of RS-485 cable
Corresponding pin of
RS-422 cable
1 RXD- White
2 TXD-
Black Red
3 RXD+ Green
4 TXD+ Red Black

10
2. Camera Installation
2.1 Matters Needing Attention
1. All of the installation work should be serviced by qualified technical
personnel or system installers.
2. Handle with care when unpacking and removing the camera; do not
impact the camera and other parts of the camera with hard objects to
avoid preventable problems.
3. Do not handle the camera head when holding the camera; do not
randomly rotate the camera head.
4. Hold the bottom of the camera when installing, do not touch very
easily damageable parts.
5. Camera installation location should be as far as possible from high
voltage, and protective measures should be done if necessary.
6. If the control system cannot setup the address of the camera, the
address of the camera must be setup with code switch before
installation.
7. Please carefully hold the camera and be sure to follow the steps and
methods of operation described in this specification.
8. The total weight of this product is no more than 1.5 kg. For safety, all
mechanical connections and connecting devices for supporting this
product must be able to withstand more than 5 times loads of the
total weight.

11
2.2 Installation
There are two installation methods of the camera: a) tabletop installation
and b) ceiling installation.
a) Tabletop installation
b) Ceiling installation

12
3. Camera Video Out Mode
3.1 Switch Configuration
Before using the camera, configure the DVI interface output color format,
etc. Switch 2, to configure these settings is located on the back panel of
the camera. The below figure shows switch 2 on the back panel, the ON
direction is marked beside the switches.
¾SW2 Pos 3
Pos 3 Setting
OFF DVI-I output color format is YUV.
This mode is used for DVI-YPbPr and DVI-HDMI interface.
ON
DVI-I output color format is RGB.
This mode is used for DVI - DVI-D, DVI - VGA and
DVI - 5-BNC (RGBHV) interface.
¾SW2 Pos 4
Pos 4 Setting
OFF Doom speed is related with current optical zoom position. The
more to the telephoto end, the slower (and more accurate) it
goes.
ON Doom speed is not related with current optical zoom position.

13
¾SW2 Pos 5
Pos 5 Setting
OFF Camera video default format: (SD: PAL, HD: 1080i50).
ON Camera video format defined by user.
¾SW2 Pos 6
Pos 6 Setting
OFF 50 Hz format
ON 60 Hz format
¾SW2 Pos 8
Pos 8 Setting
OFF Open the remote control sensor
ON Close the remote control sensor
¾SW2 Pos 1, 2, 7
Reserved.

14
3.2 Format Configuration
Video Format HD-SDI YPbPr HDMI DVI-D VGA 5-BNC
1080
p
60
√
√
√
√
√
√
1080p50 √√√√√√
1080p30 √√√√√√
1080p25 √√√√√√
1080i60 √√√√√√
1080i50 √√√√√√
720p60 √√√√√√
720p50 √√√√√√
720p30 √× √√× ×
720p25 √× √√× ×
Optimize Menu Digital Analog Digital Digital Analog Analog
Switch 2
—
— Pos 3 is set to OFF Pos 3 is set to ON
Color Format YUV RGB

15
Note: perhaps, some common display devices cannot support 1080p30/1080p25/
720p30/720p25 format.

16
4. Remote Control
1. Reserved
2. HOME (PAN/TILT init)
3. Reserved
4. IRIS control (Iris opened or
closed)
5. PAN/TILT control (up, down,
left, right, left-up, left-down,
right-up, right-down)
6. Frame scan
7. SCAN1 (Scan 300°)
8. SET (Set preset)
9. Number keys (0~9)
10. BACK (Menu ON/OFF button)
11. POWER (Power control)
12. BLC (Backlight compensation
mode switch)
13. Zoom control (Zoom wide or
tele)
14. Focus control (Focus far or
near)
15. SPD (Speed switch)
16. SCAN2 (Scan 180°)
17. CRUISE (Auto cruise)
18. CLEAR (Clear preset)
19. CALL (Call preset)
20. Reserved

17
1. Power-on initialization
When the camera is powered on, the power lamp is on, and pan/tilt will
rotate automatically, finally pan/tilt stops and the camera lens is pointing
forward.
2. Pan/Tilt control
Press the arrow buttons to change camera direction. While adjusting the
picture on the screen, press the desired arrow button. To move the
camera little by little, press the button just for a moment. To move the
camera in a wide range, press and hold the button.
3. Change camera speed
The camera’s pan/tilt speed can be switched between fast and slow
mode, when the fast mode is on, press the SPD (speed change) button,
the camera will switch to slow speed mode and vice versa.
4. Focus control
The camera is in the focus auto mode by default, but sometimes you
should control the focus manually. It can be realized by pressing the
focus control button, first switch the camera to the manual focus mode,
and afterwards adjust the focus until the button is released. When
controlling pan, tilt or zoom, the camera switches automatically to the
focus mode automatically.
5. Zoom control
The camera is equipped with a 20X optical lens, you can adjust the
zoom ratio by the WIDE/TELE button. When the WIDE/TELE button is
pressed, the video will zoom in/zoom out until you release the button.

18
6. Camera reset
Press the HOME button, the camera will reset and reinitialize the Pan/tilt
direction.
7. Back light ON/OFF control
When one portion of an image is brilliantly bright while the other portions
are dark, video will become dark. You can improve the video quality by
turning on the backlight compensation function. Pressing the BLC button
will switch the camera to the BLC ON mode. Pressing the BLC button
again will switch the camera to the BLC OFF mode.
8. Preset control
Through the remote controller, you can set / clear / call preset positions.
Set preset: [Number keys] (input the preset number) + [SET button];
Call preset: [Number keys] (input the preset number) + [CALL button];
Clear preset: [Number keys] (input the preset number) + [CLEAR
button].
9. Cruise
Press the [CRUISE] button to enable the camera to automatically scan
the preset positions constantly back and forth in the order.
10. Camera Scan
Press the [ ] button to scan within the range of the preset left and
right positions back and forth at a constant speed automatically.
Press the [SCAN1] button to scan within the range of 0~300°
automatically.
Press the [SCAN2] button to scan within the range of 0~180°
automatically.

19
5. Menu Function
5.1 Remote Control Menu
Note:
)Camera has no response for Remote Control command and COM command under OSD menu
mode;
)There is no OSD menu for SD video;
)To make new setting valid, please exit menu and restart system.