Takstar P1 User manual

P1 Presentation Remote User's Manual
P1翻页笔使用说明

• 采用2.4GHz技术无线技术，即插即用，
性能稳定；
• 支持音量控制，翻页、全屏、播放幻灯
片等；
• 3R红色激光，百米控制距离，满足大型
会议需求；
• 操作简单，轻松上手，功能一目了然；
• 采用硅胶按键设计，按键超强手感，符
合人体美学设计；
产品特性
1
尊敬的用户：
感谢您选购得胜P1翻页笔，为了您能
够更好的了解使用本产品，建议您在使用
前仔细阅读本说明书。
若存在有疑问或者您有宝贵的建议，可通
过拨打得胜官方服务热线 400 6828 333
或微信扫描二维码关注得胜官方
公众号与我们联系。
前言
P1 翻页笔

发射器:
• 遥控方式：无线射频2.4G
• 使用距离：30米以上
• 激光波长：650nm
• 激光类型：3R类激光
• 激光距离：＞200米
• 激光功率：＜5mW
• 激光颜色：红色
技术参数
• 迷你机身，内置接收器，磁吸式设计，
可存储在演讲笔中，会议，讲座一支笔轻
松搞定。
适应范围
翻页笔…………………………1支
USB接收器…………………………1个
绒布袋……………………………1个
7号电池……………………………1节
说明书…………………………1份
产品配置
2
课堂教学、授课、培训、演讲等各种PPT展
示场合
P1 翻页笔

接收器：
• 操作系统：Windows/Android/
Mac OS/Linux
• 接收尺寸：20X13X5mm
• 接收重量：1.2g
注：以上数据由得胜实验室测试得到。
功能示意
3
• 电池：1节3A电池（7号）
• 3A电池：1.5V
• 单机重量： 约25g
• 产品规格：约138.1X24.2X14.1mm
⑧ 音量-
① 电源开关
② 指示灯
③ 超链接键 ④ 上翻页按键
⑤ 下翻页按键
⑥ 激光束按键
⑦ 音量+
P1 翻页笔

4
功能键 功能操作说明
电源开关
指示灯
超链接键
上翻页按键
下翻页按键
激光束按键
音量+
音量-
正常工作时，
指示灯提示正在工作
按下激光射出，
松开按键关闭激光
点按逐渐增大音量
点按逐渐减小音量
单击：Tab
双击：Enter
长按：Alt+Tab
短按：上翻页
长按：全屏播放/退出全屏
（播放PPT时）
短按：下翻页
长按：黑屏/退出黑屏
（播放PPT时）
打开PowerPoint或Keynote软件，翻页功
能需要在全屏的状态下才能正常使用，
WPS部分版本功能不兼容
P1 翻页笔

5
一、电池安装：
二、安装USB接收器：
产品使用一节7号（AAA）电池供电，打
开电池盖，按照电池的正负极方向正确装
入电池，再把电池盖装回原来位置即可。
电池使用注意事项：
① 请确认电池的负极（-）和正极（+）是
否安装正确；
② 请勿将用尽或损坏的电池留在本产品
中，避免电池久置漏液；
③ 长期不使用本产品，请将电池取出；
④ 当本产品无功能或遥控距离缩短时，请
更换新的电池。
本产品采用一体式设计，接收器内嵌于产
品之内。如图所示，将翻页笔尾部的接收
器取出，然后把USB接收器插入电脑
USB接口，同时Windows操作系统右下角
会显示“正在安装设备驱动程序软件”，待
系统识别并显示“设备准备就绪”时，表示
USB接收器安装完成。
使用说明
P1 翻页笔

6
遥控器
无法开机 电池原因
1.请确认电源
开关是否打开
2.电池电量低
请更换电池
请与当地售后
服务网点联系
1.请确认USB
接口是否正常
2.尝试其他
USB接口
电脑USB
接口故障
遥控器
和接收器
连接失败
无法识别
接收器
不能
正常工作
将翻页笔尾部的接收器取出
把USB接收器插入电脑USB接口
故障排除
P1 翻页笔

为避免电击、高温、着火、辐射、爆炸、
机械危险以及使用不当等可能造成的人身
伤害或财产损失，使用本产品前，请仔细
阅读并遵守以下事项：
1.本产品具有产生激光束的功能，切勿将
激光直射眼睛，以免造成眼睛不适或损
伤；
2.使用中若发现有异常（如冒烟、异味
等），请立即关闭电源开关，然后将产品
送售后服务网点检修；
3.本产品及附件都应放置在室内干燥通风
处，请勿长期存放在潮湿、灰尘多的环
境，使用中避免靠近火源、雨淋、进水、
过度碰撞、抛掷、振动本机及覆盖通风
孔，以免损坏其功能；
4.使用该产品时需遵守相关安全规定，法
律法规明确禁止使用场合请勿使用本产
品，以免导致意外事故；
5.请不要自行拆机改装或维修，以防止出
现人身伤害，如有问题或服务需求请联系
当地售后服务网点跟进处理。
7
安全警示
P1 翻页笔

8
关于图标含义解释
此符号表示，根据WEEE指令
(2012/19/EU)和国家法律，由于
这种类的废弃物会有潜在的有害物质，可
能对环境和人类健康产生负面影响，所以
本产品不应与您的家庭垃圾一起处置，应
将本产品应交由授权的电气和电子设备
（WEEE）回收站回收。同时，您在正确处
理本产品的同时将有助于自然资源的有效
利用。如需了解更多有关您可以在何处放
置废物回收设备的信息，请联系您当地的
城市办事处、废物管理局或家庭废物处理
服务部门。
P1 翻页笔

9
本说明书中内容符合截止印刷之日的技术
规格。由于得胜公司会不断改进产品， 本
说明书可能不符合您的特定产品的技术规
格。要获取最新版说明书，请访问得胜官
网，然后下载说明书文件。技术规格、设
备或另售的附件在各个地区可能有所不
同，如有问题请与当地得胜销售网点确
认。如需更多支持和深层产品信息，请浏
览得胜官方网站：
https://www.takstar.com/
关于本说明书
P1 翻页笔

10
• 2.4GHz wireless technology, ready
for use once plugged in.
• Volume control, slide control, full
screen mode and slideshow play.
• Class 3R red laser with 100m range,
up to large conference requirements.
• Simple-to-use, intuitive controls.
Features
Dear Customer,
Thank you for purchasing Takstar P1
Presentation Remote. In order to
better understand and use the
product, please read this manual
carefully.
If you have any questions or
suggestions, please contact our local
dealer.
Preface
P1 Presentation Remote

11
• Comfortable silicone buttons,
aesthetically pleasing as well.
• Mini design with a magnetic dock
that stores the USB receiver. One
remote to get the show started.
Various PowerPoint occasions during
lecture, training and presentation.
Applications
Presentation Remote ………………1 pc
USB Receiver… … … … … … … … 1 pc
Velvet Bag……………………………1 pc
AAA Battery……………………………1 pc
User Manual…………………………1 pc
Package Contents
P1 Presentation Remote

12
Transmitter:
• Control Method: wireless RF 2.4GHz
• Use Distance: above 30m
• Laser Wavelength: 650nm
• Laser Type: Class 3R laser
• Laser Distance: ＞200m
• Laser Power: ＜5mW
• Laser Color: red
• Battery: 1 × AAA battery
• AAA Battery: 1.5V
• Weight: about 25g
• Dimensions: about 138.1*24.2*14.1mm
Receiver:
• Operating System:Windows/Android/
Mac OS/Linux
• Dimensions: 20*13*5mm
• Weight: 1.2g
Specifications
Note: The above data are measured by
Takstar laboratory.
P1 Presentation Remote

13
Operations
Power
Switch
Indicator
Light
Hyperlink
Button
Move upwards/
downwards to power
on/off respectively.
Indicator lights up
during normal
operation.
Single click: Tab
Double click: Enter
Long press: Alt+Tab
Function Descriptions
⑧ Volume −
① Power Switch
② Indicator Light
③ Hyperlink Button ④ Page Up
⑤ Page Down
⑥ Laser Button
⑦ Volume +
P1 Presentation Remote

14
Page Up
Page Down
Laser
Button
Volume +
Volume −
Press and hold to
activate the laser
pointer.
Tap to gradually
increase volume level.
Tap to gradually
decrease volume level.
Short press: previous
pageLong press:
enter/exit full screen
(during slide show)
Short press: next page
Long press: enter/exit
black screen
( )during slide show
Open PowerPoint or Keynote, page
turning only works properly in full
screen mode.And some WPS Office
versions are incompatible.
P1 Presentation Remote

15
Battery Installation:
The unit is powered by 1 × AAA
battery. Remove the battery
compartment cover, insert the battery
into the battery holder following the
polarity instruction, and put the
battery compartment cover back in
position.
Note:
① Make sure to install the battery by
observing the correct polarity.
② Do not leave bad or exhausted
battery in the product.
③ If you do not use the product for a
long period of time, remove the
battery to avoid possible damage
from battery corrosion.
④ If the product does not function
correctly or if the operating range
becomes reduced, try to replace the
battery with new one.
Operation Instructions
P1 Presentation Remote

16
USB Receiver Installation:
The remote features integrated
design with built-in storage slot for
the receiver. Remove the receiver
from the bottom of the remote, then
connect the USB receiver to a USB-A
Port on the host computer. In
Windows system, a pop-up should
appear at the bottom right of the
desktop saying “Installing device
driver software”. When the
installation completes, you will see
“Ready to use”, meaning the USB
receiver is successfully installed.
Take out receiver from
the bottom of Remote
Insert the USB receiver into a USB interface
on computer
P1 Presentation Remote

17
Issue
Cannot
turn on
the
remote
Power
supply
issue
1. Make sure
the power
switch is on.
2. Battery
level is low,
replace with
a new one.
Please
contact our
local after-
sales service
outlet.
1. Check if the
USB port
malfunctions.
2. Try other
USB ports.
Computer
USB port
malfunction
Failed
connection
between
the remote
and
receiver
Cannot
recognize
the
receiver
Does not
work
properly
Cause Solution
Troubleshooting
To avoid electric shock, overheat, fire,
radiation, explosion, mechanical risk
and injury or property loss due to
Safety Instructions
P1 Presentation Remote

18
improper use, please read and observe
the following items before use:
1. This product generates a laser beam.
Do not point the laser towards eyes to
avoid eye discomfort or injury.
2. If there is any abnormality during
use (e.g., smoke, strange odor), please
kill the power switch and unplug from
power source, then send the product
to the after-sales service outlet for
repair.
3. Keep this product and its accessories
in a dry and ventilated area. Do not
store in a humid or dusty area for
extended time. Keep away from fire,
rain, liquid intrusion, bumping,
throwing, vibrating, or from blocking
any ventilation openings, to prevent
malfunction.
4. Abide by relative safety rules during
operation. Do not use it if prohibited by
laws and regulations to avoid accident.
P1 Presentation Remote

19
5. Do not disassemble or repair the
product by yourself to avoid injury. If
you have any questions or require any
services, please contact our local after-
sales service outlet.
Label Meanings
This symbol indicates that
this product should not be
disposed of with your household
waste, according to the WEEE
directive (2012/19/EU) and your
national law. This product should be
handed over to an authorized
collection site for recycling waste
electrical and electronic equipment
(WEEE). Improper handling of this type
of waste could have a possible
negative impact on the environment
and human health due to potentially
hazardous substances that are
generally associated with WEEE. At
P1 Presentation Remote