Takstar ECA-032 User manual

产品特性
技术参数
注意事项
标准配置
适用场合
中小型宴会厅、多功能厅、大型会议室等
1. 为保证吊挂安全，单边最多不超过20只线阵列全频音箱。
2. 确保功率放大器和音箱的功率、阻抗相匹配，失衡搭配可导致设备损坏或音质效果不佳。
3. 音箱的安装需由专业工程人员进行，应固定牢靠，并选择安装在不易碰触的位置。
4. 使用时，音箱高音号角朝向听众区域，以确保获得较佳听感。
5. 搬运音箱时，请小心轻放，保护好音箱不受损坏。
6. 音箱使用完后，音箱上的插销、连接杆固定在音箱上，以免丢失。
1. 全频音箱（ECA-032）与全频音箱（ECA-032）通过吊挂件
三点连接，其中后板吊挂 件通过插销可进行垂直角度0°-10°
六档调节（如图1）；
2.
全频音箱（ECA-032）与超低音音箱（ECA-081SUB）三 点
连接，底板吊挂件通过螺栓对垂直角度两档调节（如图2）。
3.四只线阵列全频音箱为一组，用3条连接线并联， 并联后阻
抗值为4Ω。建议一组全频音箱接专业功放EKA-3A/3D/403/403D
的一个通道。
ECA-032音箱×2
说明书×1
尊敬的用户：
欢迎使用ECA-032线阵列全频音箱，配套ECA-081SUB超低音音箱，该音箱小巧美观，吊挂安装、角度调节方便；
音质方面，层次清晰、细腻耐听。适用于室内语音扩声及放音。使用前请您仔细阅读说明书，以便能正确的操作使用。
若存在有疑问或者您有宝贵的建议，可通过拨打得胜官方服务热线 400 6828 333 或使用微信扫描二维码关注得
胜官方公众号与我们联系。
ECA-032线阵列全频音箱
邮编：516121
广东省电声工程技术研究开发中心
广东省得胜电子有限公司制造
地址：广东省惠州市博罗县龙溪镇富康一路2号 全国服务热线：400 6828 333
传真：[phone]
邮箱：[e-mail] 扫一扫，了解更多产品
额定功率：40W
额定阻抗：16Ω
频率响应（±3dB）：100Hz-20kHz
灵敏度（1W/1M）：92dB
覆盖角：H120°×V45°
最大声压级：108dB
分频模式：无源二分频
分频点：2500Hz
吊挂／安装：吊挂件连接，垂直角度0°-10°可调
接线方式：2×NL4speakon（IN1+、1-，LINK1+、1-）
箱体板材： 5mm+9mm+15mm夹板
表面处理：白色聚亚安酯小点漆
高频：1″×2（25芯），丝膜球顶
低频：3″×2（20芯），70磁钢
规格（mm）：302×167×112mm（W×D×H）
重量：净重2.4Kg
单元结构上由双3寸20芯纸盆中低音和双25芯丝膜球顶高音组成。低音采用弹性与耐疲劳性俱佳的橡胶折环，中低频反应迅速、 动
态足；磁路采用对称设计，谐波失真小。高音采用透明丝膜，高频透亮平滑、细腻；采用钕铁硼磁路，质量轻，高频纤细，细节
表现力好；磁路间隙中填充磁液，能有效降低音圈温度，提升高音可靠性；配上特定指向性号角，能有效控制垂直辐射范围。
分频器元件采用了损耗值较低的无氧铜电感、高品质聚丙烯电容，使分频网络稳定，音质出众。
箱体采用梯形结构，内壁贴附吸音棉能减少驻波的产生，使中低频在听感上表现得更干净，频响上更平坦；箱体结构紧凑，采用
铝吊挂件连接，垂直角度0°-10°六档可调，可根据场地大小灵活配置音箱数量和调节辐射角度。
多只音箱组合近似线性声源，具有水平覆盖均匀、垂直指向性强、辐射区域内声能衰减较小的特点。
安装方式
图1 图2
ECA-032
插销孔
C-C 垂直角度5°
C-B 垂直角度0°
ECA-081SUB
5°0°
B C
C
ECA-032
ECA-032
A-1 垂直角度9°
A-2 垂直角度6°
A-3 垂直角度0°
B-2 垂直角度10°
B-3 垂直角度4°
C-3 垂直角度8°

Features
Caution
Product Content
Application
Medium or small banquet hall, multifunction hall, large conference room
1. To ensure installation safety, the full range speaker cabinet quantity can not be more than 20 on one side.
2. Make sure the power and impedance of speaker cabinet match with that of the power amplifier, otherwise it leads to equipment damaged
or bad sound.
3. Ask professional technician for installation.
4. During operation, keep the horn toward the audience for better effect.
5. Handle with care during transportation.
6. After operation, fix the connection bar and pin on the cabinet to prevent from losing them.
1. Connect one ECA-032 with another ECA-032 via connection
parts at three points. Use the pin to adjust vertical angle 0°-10°
in 6 steps (refer to figure 1).
2. Connect ECA-032 with the subwoofer ECA-081SUB at three
points. Use the bolt to adjust vertical angle in two steps (refer to
figure 2).
3. Four full range speaker cabinets can be installed as a group
in a parallel way via 3 cables, 4Ω impedance after connection.
It is recommended to use one channel of power amplifier
EKA-3A/3D/403/403D for one group of speaker cabinets.
ECA-032 speaker cabinet ×2
User manual×1
Dear Customer,
Thank you for purchasing ECA-032 line array full range speaker cabinet which used with ECA-081SUB subwoofer together. ECA-032
features compact contour, easy installation and adjustment, clear and delicate sound.
Please read the user manual carefully before operation and keep it for reference in future.
ECA-032 Line Array Full Range Speaker Cabinet
Installation
The line array is designed with 3 inch 20mm cone MFHF and dual 25mm silk dome tweeter. The woofer features elastic and durable rubber
surround for quick and dynamic MFLF, symmetric magnet circuit for low harmonic distortion. The tweeter features transparent silk
diaphragm for flat and bright treble, NdFeB magnet for light weight and slender but detailed treble. The magnet loop is filled with magnet
liquid to reduce the voice coil temperature and meanwhile boost the reliability. Specific directivity horn is designed together to effectively
control the vertical audio projection range
The crossover is designed with low consumption OFC inductor and high quality polypropylene for reliable performance and prominent sound
The trapezoidal enclosure is designed with acoustic foam to eliminate standing wave but boost the pure MFLF and flat frequency response.
The compact enclosure is connected via Al pieces, vertically 0°-10°adjustable in 6 steps. The speaker cabinet quantity and projection angle
can be adjusted according to the actual installation requirement
Linear audio source, even horizontal coverage, strong vertical directivity, low attenuation in the projection range
Specification
Rated Power: 40W
Rated Impedance: 16Ω
Frequency Response(±3dB): 100Hz-20kHz
Sensitivity(1W/1M): 92dB
Coverage: H120°×V45°
Max SPL: 108dB
Crossover Mode: two way passive
Crossover Frequency: 2500Hz
Suspension/Installation: flying suspension, vertical 0°-10°adjustable
Wiring: 2×NL4speakon(IN1+, 1-，LINK1+, 1-)
Enclosure: 5mm+9mm+15mm plywood
Finish: white painting
Tweeter: 1″×2(25mm)，silk dome
Woofer: 3″×2(20mm)，70 magnet
Dimension(mm): 302×167×112mm(W×D×H)
Net Weight: 2.4Kg
Figure 1 Figure 2
ECA-032
pin connection hole
C-C vertical angle 5°
C-B vertical angle 0°
ECA-081SUB
5°0°
B C
C
ECA-032
ECA-032
A-1 vertical angle 9°
A-2 vertical angle 6°
A-3 vertical angle 0°
B-2 vertical angle 10°
B-3 vertical angle 4°
C-3 vertical angle 8°
Guangdong Takstar Electronic Co., Ltd.
Address: No. 2 Fu Kang YiRd., Longxi Boluo Huizhou, Guangdong 516121 China
Tel: [phone] Fax: [phone] Email: [e-mail] Website: www.takstar.com