TAMURA TZ-3157 User manual

2D-53-0002730A
本製品󴁵廃棄󴁲󴁫い󴁭
本製品󴂙廃棄󴁠󴂒場合󴁶󴀯各自治体󴁵指示󴁲従󴁪󴁭処理󴁞󴁭󴁜い󴀰
取扱󲂾明書
MOUNTING BRACKET
型番：TZ-3157
󴁚󴁵取扱󲂾明書󴁲󴁶󴀯事故󴂙防󴁗󴁦󴂈󴁵重要󴁱注意事項󴁯製品󴁵取󴂑扱い󴁒󴁦󴂙示
󴁞󴁭い󴂅󴁠󴀰󴁚󴁵󴀹取扱󲂾明書󴀺󴂙󴂏󴁖󴁑󲂿󴂆󴁵うえ製品󴂙安全󴁲󴁑使い󴁜い󴀰󴁑󲂿󴂆
󴁲󴁱󴁪󴁦あ󴁯󴁶󴀯い󴁫󴁮󴂉見󴂐󴂓󴂒󴁯󴁚󴂔󴁲必󴁡保管󴁞󴁭󴁜い󴀰

2D-53-0002730A
1󴆁商品概要
NT110 󴃌󴂽󴃄ル󴂯󴄁󴃌󴂨󴂯󴃤キ󴂺󴄁󴂙ラック󴃣󴂫ン󴃍󴂅󴁦󴁶󴃋󴄁󴃛ル埋󴂈込󴂆󴁠󴂒󴁦󴂈󴁵
EIA 󴂺󴂩󴂿󴃛ラケッ󴃍金具󴁮󴁠󴀰
2󴆁構成
名称
数量
備考
󴃣󴂫ン󴃍󴃛ラケッ󴃍金具
2
塗装色 黒色
本体取󴂑付󴁘用ネ󴂽
8
M4x8mm󴀯黒色
ハン󴃎ル
2
塗装色 黒色
ハン󴃎ル取󴂑付󴁘用󴂺ラネ󴂽
4
M5x12mm󴀯黒色
ラック󴃣󴂫ン󴃍󴂅󴁦󴁶󴃋󴄁󴃛ル埋󴂈込󴂆󴁠󴂒󴁯󴁔󴁵取󴂑付󴁘用ネ󴂽󴁶添付󴁞󴁭󴁑󴂑󴂅󴁢󴂚󴀰
取󴂑付󴁘󴂙行うラック󴂅󴁦󴁶󴃋󴄁󴃛ル側󴁮指定󴁵ネ󴂽󴂙用意󴁞󴁭󴁜い󴀰
3󴆁様
外形寸法
532.6󳡋W󳡌×26󳡋H󳡌×61(D)mm
質量
660g (片側)

2D-53-0002730A
4󴆁寸法図

2D-53-0002730A
5󴆁取󴂑付󴁘方法
NT110 󴁵󴂺󴂩󴃎部へ󴃣󴂫ン󴃍󴃛ラケッ󴃍金具󴂙取󴂑付󴁘󴂅󴁠󴀰
󳶖NT110 󴁵外装品󴅻󴂺󴂩󴃎パネル󴀯パッ󴃎󴅼󴂙取󴂑外󴁞󴂅󴁠󴀰
外装品󴂙取󴂑外󴁠方法󴁶 NT110 取扱󲂾明書󴂙参照󴁞󴁭󴁜い󴀰
󳶗󴃣󴂫ン󴃍󴃛ラケッ󴃍金具󴁲ハン󴃎ル󴂙取󴂑付󴁘󴂅󴁠󴀰
付属󴁵取󴂑付󴁘ネ󴂽󴂙使い取󴂑付󴁘󴂅󴁠󴀰
󳶘NT110 󴁵󴂺󴂩󴃎部へ󴃣󴂫ン󴃍󴃛ラケッ󴃍金具󴂙取󴂑付󴁘󴂅󴁠󴀰
図󴁵矢印󴁵位置󴂙参照󴁞󴁭ネ󴂽󴂙取󴂑付󴁘󴁭󴁖󴁧󴁜い󴀰
必󴁡付属󴁵取󴂑付󴁘ネ󴂽󴂙使用󴁞󴁭󴁖󴁧󴁜い󴀰そ󴂓以外󴁵ネ󴂽󴂙使用󴁠󴂒󴁯󴀯
󴃣󴂫ン󴃍󴃛ラケッ󴃍金具󴁓外󴂓󴁦󴂑󴀯NT110 破損󴁵原因󴁯󴁱󴂒恐󴂓󴁓あ󴂑󴂅󴁠󴀰

2D-53-0002730A
6󴆁埋󴂈込󴂆設置時󴁵注意事項
󴃣󴂫ン󴃍󴃛ラケッ󴃍金具󴂙使用󴁞󴁭 NT110 󴂙ラックや󴃋󴄁󴃛ル󴁲埋󴂈込󴂆設置󴁠󴂒󴁯󴁔
󴁶󴀯記注意事項󴁲従い正󴁞󴁖󴁛使用󴁜い󴀰
󴆄󴅼 埋󴂈込󴂆設置󴁠󴂒󴁯󴁔󴁶󴀯空気󴁵循環󴂙考慮󴁞󴁦構造󴁯󴁞󴁭󴁜い󴀰
󴆅󴅼 NT110 󴁲接続󴁠󴂒ケ󴄁󴃛ル󴁲無理󴁱力󴁓掛󴁒󴂐󴁱い󴂏う󴀯󴂅󴁦通風󴂙確保󴁠󴂒󴁦󴂈󴀯
以󴁵空間󴂙空󴁘󴁭設置󴁞󴁭󴁜い󴀰
󴄀底面：󴂹󴃥足󴁵高󴁜以󴁵空間󴂙空󴁘󴂒󴁚󴁯
󴄀背面：130mm 以󴁵空間󴂙空󴁘󴂒󴁚󴁯
󴆆󴅼 NT110 󴁵パネル󴂙開閉󴁠󴂒󴁯󴁔󴁲ラックや󴃋󴄁󴃛ル󴁯接触󴁠󴂒󴁦󴂈󴀯手前󴁶󴃛ランクパ
ネル等󴁵脱着可能󴁱パネル󴂙実装󴁠󴂒󴁱󴁰󴀯1U 空󴁘󴁭設置󴁞󴁭󴁜い󴀰
󴆇󴅼 NT110 󴁵設置角度󴁶󴀯0°󴅻底面水平󴅼～󴆀7°󴅻󴃚󴂬󴄁󴃅󴄁面水平󴅼内󴁮󴁛使用
󴁜い󴀰
＜NT110 󴃋󴄁󴃛ル埋󴂈込󴂆設置󴁵例＞
手前󴁶 1U 󴂾ペ󴄁󴂾󴂙空󴁘󴂒
󴅻脱着可能󴁱パネル󴁵実装可󴅼
󴃋󴄁󴃛ル
底面󴁶󴂹󴃥足󴁵高󴁜以󴁵
空間󴂙空󴁘󴂒
背面󴁶 130mm 以󴁵
空間󴂙空󴁘󴂒

2D-53-0002730A
󴂰󴂾󴃄󴃣󴄁󴂺󴄁ビ󴂾󴁲󴁫い󴁭
󴁛使用中󴁲不具合󴁓発生󴁞修理󴂙必要󴁯󴁠󴂒場合󴀯󴂅󴁦動作運用󴁲󴁫い󴁭󴁛
不審󴁵点󴀯そ󴁵弊社取扱品目󴁲󴁫い󴁭󴁛不明󴁵点󴀯あ󴂒い󴁶󴁛用命事項󴁓󴁛󴁝い󴂅
󴁞󴁦󴂐記あ󴁭󴁛連絡󴁜い󴀰
󴅻󴁱󴁑󴀯修理󴄀再調整󴁵期間短縮󴁵󴁦󴂈󴁲󴀯故障時前後󴁵󴁛使用状況󴄀経歴等󴂙
詳細󴁲󴁑知󴂐󴁢󴁜い󴀰󴅼
本社󴆂〒178-8511 東京都練馬区東大泉 1-19-43
TEL[phone] FAX[phone]
󴁑問合󴁢先
󴃛ロ󴄁󴃎󴂸󴃥事業部 営業部󴆂本社内
TEL[phone] FAX[phone]
西日本営業所󴆂〒564-0062 大阪府吹田市垂水町 3-27-27
第2江坂昌ビル
TEL[phone] FAX[phone]

2D-53-0002730A
About disposal of this product
When disposing of this product, please follow the instructions of each
municipality.
Instruction Manual
MOUNTING BRACKET
Model Number:TZ-3157
This Instruction Manual describes important precautions to prevent any
accident and procedures to handle this product.Read this Instruction Manual
carefully to use this product safely.
After reading, keep this in a safe place where users can refer to as
needed.

2D-53-0002730A
1󴆁Overview
This is a EIA size bracket fitting for rack mount or table embedding of
NT110 digital audio mixer.
2󴆁Configuration
Item name
Quantity
Remarks
Mounting Bracket
2
Paint color black.
Mounting Screw
8
M4x8mm,
Paint color black.
Handle
2
Paint color black.
Handle mounting screw
4
M5x12mm,
Paint color black.
Mounting screws for rack mount or table embedding are not included.
Please prepare the specified screw on the rack or table side to be mounted.
3󴆁Specifications
Dimensions
532.6(W)×26(H)×61(D)mm
Weight
660g(one side)

2D-53-0002730A
4󴆁Dimensions

2D-53-0002730A
5󴆁Mounting method
Mount the mounting brackets to the side of the NT110.
󳶖Remove the NT110 exterior parts (side panels, pads).
How to remove the exterior parts, refer to the NT110 instruction manual.
󳶗Attach the handles to the mounting brackets.
Use the mounting screws provided.
󳶘Mount the mounting brackets to the side of the NT110.
Please refer to the position of the arrow in the figure below and install
the screw.
Be sure to use the included mounting screws. If you use other screws,
The mounting bracket metal fittings may come off, or NT110 may be
damaged.

2D-53-0002730A
6󴆁Precautions for Embedding Installation
When installing NT110 in a rack or table using mount bracket metal fittings,
please use it correctly according to the following notes.
1) When installing it, please structure with air circulation taken into
consideration.
2) To prevent excessive force from being applied to the cable connected to
the NT110, and to ensure ventilation, please leave the following space
open.
󴄀Bottom: Make space more than rubber foot height
󴄀Back: Leave space of 130 mm or more
3) In order to make contact with the rack or table when opening / closing the
panel of NT110, install 1 U with front side installing detachable panel such
as blank panel etc.
4) The installation angle of NT110 should be used within 0 ° (bottom level) to
-7 ° (horizontal fader plane).
＜Example of NT110 table embedded installation＞
Leave 1U space in front
󴅻Can mount removable panel󴅼
table
Leave space above the height
of rubber feet on the bottom
Space above 130 mm
on the back

2D-53-0002730A
About Customer Service
If you experience any problems with our products and require any servicing,
or have any questions about TAMURA product line, please contact your
TAMURA sales representative or TAMURA at the following locations.
To help speed up servicing and readjustment, please be ready to describe
the problem accurately, what operations you were performing before and
after it happened, or the history of usage.
󴅻Head Office󴅼
1-19-43, Higashi-Oizumi, Nerima-ku, Tokyo, 178-8511 Japan
Phone : [phone] Fax : [phone]
(Contact)
International Sales Broadcom Business Unit
Phone : [phone] Fax : [phone]