Tanaka 746280 User manual

Owner’sManual
PROFESSIONAL CUTTING HEADS
ISM, Inc. • 1028 4th St. SW • Auburn, WA 98001 • Phone: [phone] • Fax: [phone] • www.tanakapowerequipment.com
Safety Instructions
1.) *Warning! Read this owners manual as well as
the owners manual supplied with your grass trimmer.
Be sure to follow all warnings and safety instructions.
Failure to do so can result in serious injury to the
operator and/or bystanders.
2.) Wear eye protection that complies with ANSI
Z87-1 standard.
3.) Do not operate this or any type of power
equipment when you are tired, ill, or under the
influence of alcohol, drugs, or medication.
4.) Always wear heavy long pants, boots, and
gloves. Do not wear loose clothing, short pants,
sandals, or go bare foot. Secure hair so it is above
shoulder level.
5.) Inspect unit before each use. Replace parts that
may be cracked, chipped, or damaged in any way.
Make sure the cutting head is properly installed and
securely fastened. Be sure the cutting attachment
shield is properly attached in the position recom-
mended by the manufacturer.
6.) Clear the work area before each use. Remove
all objects such as rocks, broken glass, nails, wire,
or string which can be thrown or become entangled
in the cutting head. Clear the area of children,
bystanders, and pets in a 50 foot (15m) radius. It is
recommended that bystanders wear eye protection.
If you are approached, stop the engine and cutting
attachment immediately.
FIXED LINE
ITEM NUMBER
746280
MANUAL FEED
ITEM NUMBER
746290
Aluminum
Cutting Heads
Installation (continued)
Thisshoulderis necessary tomountthese heads
securelyandin theproperposition. Thediameterof
many mountingshoulders is1”(25.4mm) and both
headsrequirethis size.Formounting shoulderdiam-
etersthat are.79” (20mm), aspecial shimis included
inthepackage contentstoprovide thenecessary
spacing.
A variety of adapters are provided to accommodate
mounting to Tanaka as well as other units (see
sizes listed below). To mount the “Fixed Line”
head, (Ref. 1), place the recessed side on to the
mounting shoulder of the gear case. When using
the 8mm nut, always use the 10mm washer.
The“ManualFeed”head
ismounted inthe same
manner, exceptthatthe
“CutterHolder”(Ref.2-4
showbelow)must always
beused asshown in Ref.
2A&2B.
1-1 1-2
1-3
2-1 2-2
2-3 2-4
Aluminum Cutting Head Mounting Hardware
746280 / Fixed Line 746290 / Manual Feed
Installation
The Aluminum Cutting Heads
are designed for use on
straight shaft Grass Trim-
mers and they are mounted to
the unit in the same manner.
Typically, the gear case has a
separate piece or cover which
includes a mounting shoulder
on which blades are held and
centered.
WARNING!
These heads are
NOTRECOMMENDED
for use on units without a
mounting shoulder
Ref. 1
Ref. 2A
Ref. 2B
Ref.# Part No. Description
2-1 312-33386-20 Adapter Bolt
(8mmx 1.25 LHM)
2-2 313-38100-20 Adapter Nut
(10mmx 1.25 LHF)
2-3 27288 Mounting Shim
(20mmto 1")
2-4 311-37300-203 Cutter Holder
(#29592 - Page 1)
1-4
Ref.# Part No. Description
1-2 312-33386-20 Adapter Bolt
(8mmx 1.25 LHM)
1-3 313-38100-20 Adapter Nut
(10mmx 1.25 LHF)
1-4 27288 Mounting Shim
(20mm to 1")
1-5 992-01100-011 Washer (10mm)

Owner’sManual
PROFESSIONAL CUTTING HEADS
ISM, Inc. • 1028 4th St. SW • Auburn, WA 98001 • Phone: [phone] • Fax: [phone] • www.tanakapowerequipment.com
1.) This head is designed to accommodate nylon
line with a diameter of .095” - .130”. The pre-cut
lengths included in the package are 14” which will
provide a total cutting swath diameter of approxi-
mately 13”. However this length can be longer (or
shorter) depending on the following factors:
A. The diameter of line being used
B. The unit’s power
C. The desired cutting speed
D. The desired total cutting swath diameter.
2.) Fold a pre-cut length of line in half.
3.) On the gear case facing side of the head, insert
the two ends of the folded line in to the two holes
(just above the Tanaka logo) and pull them com-
pletely through the underside evenly.
4.) From the opposite side of the head, feed the
lines through the holes located on the side of the
head and pull until they are totally extended
Aluminum Cutting Heads
Nylon Line Replacement
FIXED LINE
ITEM NUMBER
746280
The Original
BRAIN
®
Manual Feed
Semi- Automatic
The BRAIN
®
2000
Fully Automatic
MANUAL FEED
ITEM NUMBER
746290
1.) This head is designed to accommodate nylon
line with a diameter of .095” - .105” and can hold up
15’ (total length). The cutting swath (determined by
the length of the line exiting the head from each
side) is variable depending on the following:
A. The diameter of line being used
B. The unit’s power
C. The desired cutting speed
2.) Fold a pre-cut length of line with one side slightly
longer than the other (as shown below).
3.) On the ground facing side of the head, insert the
two ends of the folded line in to the two holes and
pull them completely through (as shown below).
4.) Wind both lengths of line together in either
direction until 8-10” remain. Insert the shortest line
into the nearest exit hole slot then wind the
remaining line to the slot on the opposite side. More
line can be extended (in increments of 3”) by
unwinding both lines to next exit hole. The total line
length (to extend from each side) will be subject to
the factors listed above, however a good starting
length could be 6”.
TANAKA OFFERS OTHER HIGH QUALITY CUTTING HEADS
(#29592 - Page 2)
Order # 746251
Std.LineDiameter: .095”
LineCapacity:30ft./9.1m
Order # 746551
Std.LineDiameter:.095”
LineCapacity:25ft/7.6m
Order # 746751
Std.LineDiameter: .095”
LineCapacity: 20ft./6.7m
Order # 746451
Std.LineDiameter: .095”
LineCapacity: 25ft./7.6m