TANDBERG FieldView User manual

On unpacking the FieldView you should find:
FieldView Device
•
External Power Adapter•
Stylus•
Battery•
Wrist Strap•
Quick Start Guide (this document)•
CD of user guides, end-user license•
agreement and FieldView Application
software
Safety and regulatory information.
•
Streaming on/off1.
Still image capture2.
LED indicators3.
Microphone4.
Streaming indicator5.
(red = streaming/recording on)
Light6.
Lens7.
SD memory card slot8.
External power connector9.
Antenna10.
Headset connector11.
Audio line in (plug in12.
external audio source)
S-Video in (plug in13.
external video source)
USB host interface14.
Ethernet port15.
Stylus16.
Viewfinder17.
Send button18.
End button19.
Zoom/Manual focus controls20.
Navigation pad21.
Speaker22.
Focus button23.
Display mode button24.
Recording On/Off25.
Power26.
Tripod mount27.
Battery door28.
Battery lock29.
Before You Start. The FieldView Device is
designed to communicate with a FieldView
Application software client on a PC, using a
network that has already been set up and
configured.
For more information on operating the
•
FieldView Device, see the FieldView
Device User Guide provided on the
TANDBERG FieldView CD.
For information on the FieldView Applica-
•
tion software client, see the FieldView
Application User Guide provided on the
same CD.
116327.02
www.tandberg.com
11
13
14
15
23
24
25
26
12
16
17
18
20
21
19
27
28 29
22
1
7
3
45
6
2
8
9
10

Charging the Battery
Important: Before using this device for the first time you must install and charge the battery. The device will not
operate on the external adapter alone. You must have a battery installed.
!"
#$
Slide the lock switch to the
Locked position.
Connect the FieldView
Device to the external power
adapter and charge the
battery until the orange LED
turns off (up to 8 hours).
Gap
Close the battery door as follows:
Ensure lock switch is in the
•
Unlocked position.
Orient the battery door so it
•
is flat against the battery
well, but with a 3 mm gap.
Slide the door toward the
•
centre of the FieldView Device
until it is fully closed.
Open the battery
compartment and insert
the battery until it clicks
into place and is flush.
It fits one way only.
Unlocked
Locked
Slide the lock switch to
the Unlocked position.
Unlocked
Locked
116327.02

If the FieldView Device is
Off or in Standby mode,
press and release
the Power button.
Navigation Pad
Button Function
Start or accept call (Send)
End a call
Volume up
Mic mute
Volume down
Front illumination light on/off
Enter
LED Indicators
Power Green = On or Standby
Network Green = Network available
Off = Network unavailable
Battery Orange = Battery is charging
Off = Battery is charged,
or power is not connected.
Going to Standby
Press and release the Power button to go to Standby
mode. The Viewfinder turns off to use less power, but
the Power LED remains illuminated.
Note: The unit will automatically enter Standby
mode if it is On, but not used for a period
(default 2 minutes).
Turning Power Off
If the unit is On or in Standby mode, press and hold
the Power button for two seconds to turn it Off.
Turning Power On Going to Standby or Off
Power button
116327.02

If your installation requires a login, you will be prompted with a login screen on the View-
finder, as shown below. To fill this in:
Tap the1. Username field with the stylus and select your user name from the
list (your site administrator will provide this to you).
Tap the
2. Password field with the stylus. An onscreen keyboard will appear.
Use the stylus to tap characters to enter them in the
3. Password field.
Tap the
4. Login button to finish logging in.
Important: When you are using the Viewfinder screen, always use the stylus pro-
vided with the FieldView Device. Do not use other objects, as this could damage
the Viewfinder screen.
Logging in
Logging in on the Viewfinder screen
Display the Directory and use the
stylus or navigation pad to select a
name from the Local Contacts list.
Then press Send to start the call.
You will hear outgoing rings or a busy
signal.
To answer a call, press Send.
To end a call, press the End button.
Starting a Call
Answering an Incoming Call
Ending a Call
When a call has been established
(you can talk to the other user), press
the Streaming button on top of the FieldView
Device to start streaming media to the
FieldView Application software client.
Press it again to stop streaming.
Turning Streaming On or Off
Streaming button
Press the Send button to display the
Directory window.
Displaying the Directory
116327.02
Copyright © 2008 All rights reserved
www.tandberg.com