TANDBERG 220-420LTO User manual

Tandberg 220/420LTO
Half Height LTO1 and LTO2 Tape Drive
Quick Installation Guide
Revision 4 – February 2006

2
Mechanical Installation
For mechanical mounting specifications, please refer to Figure 1.
Allowed mounting position is either horizontal with the indicator LEDs to the
right, or vertical with the LEDs up.
The drive occupies a half-size 5.25-inch slot with standard holes for mounting
screws on both sides of the drive chassis and at the bottom of the drive.
Figure 1 Mounting specifications
Important!
Mounting screw
requirements
• Only M3 (metric) screws must be used for mounting the drive
• Maximum permitted screw penetration: 2.5 mm
• Minimum required screw penetration: 2.0 mm
• Screw torque, mounting screws: 0.5 Nm
• Screws are supplied with all the Tandberg 220/420LTO drive
variants
• Bags with 4 screws and 4 SCSI ID jumpers are available
(Ordering no. 43 32 65)
Do not use longer screws or higher screw torque than specified!
Figure 2 Allowed mounting orientations

3
SCSI Identification
Make sure that the drive unit has the proper SCSI-ID before it is connected to a
computer system.
Refer to manuals for host computer and application software to obtain the correct
ID. For correct mounting of ID-jumpers at the rear of the drive, please refer to
Figure 3 and Table 1.
External drives have a thumb-wheel switch to set the SCSI-ID (see Figure 6).
Power Connecto
r
SCSI Connector
Service Connector
Figure 3 Drive connectors
The factory default drive
number setting is SCSI ID = 2.
If the drive has to be set up
with a different unit number,
the jumpers (on the Service
Connector) have to be
connected according to
Table 1.
Example: SCSI ID = 3
SCSI ID=0
SCSI ID=1
SCSI ID=2
SCSI ID=3
SCSI ID=4
SCSI ID=5
SCSI ID=6
SCSI ID=7
SCSI ID=8
SCSI ID=9
Table 1
Service Connector jumper settings for SCSI
ID (Dark = Jumper mounted)
SCSI ID=10
SCSI ID=11
SCSI ID=12
SCSI ID=13
SCSI ID=14
SCSI ID=15

4
SCSI Cable
Host Last SCSI Device
Internal Terminator Connecto
r
SCSI
-
bus
10 cm
Figure 4 SCSI cable
• Internal SCSI-LVD/SE-cable with 5 connectors (Ordering no. 43 20 51)
• Internal, removable SCSI-LVD/SE-terminator (Ordering no. 43 20 53)
• External, removable SCSI-LVD/SE-terminator (Ordering no. 43 26 17)
• External SCSI 68HD/VHDCI 320MBs-cable (Ordering no. 43 32 64)
Termination
The SCSI-bus cable must be terminated in both ends according to SCSI
specifications. If the tape drive is the last device on the bus, the bus must be
terminated within 10 cm of the tape drive connection.
Tandberg 220/420LTO has a combined SCSI-LVD/SE interface embedded. The
PC-98 Specification specifies that the termination of the SCSI-bus system is a part
of the SCSI-cable and not a part of the SCSI-device.
As a result, termination cannot be turned on or off directly on the tape drive itself.
For internal devices, a SCSI-cable with an integrated terminator or a separate
terminator applied to the end connector of the cable, 10 cm from the last device,
must be used.
External devices must be terminated with an external terminator on the last device
on the SCSI-bus.
Software Installation
For Software Application support and software drivers, please see
www.tandberg.com. Then select SUPPORT and Select Product.
For installation of Backup Application software, refer to the software vendor’s
software application user guide supplied with the software or on the software
vendor’s web.

Front LED Indicators
Figure 5 Light Emitting Diodes (LED)
5
Drive State READY LED
(Green left) ACTIVITY LED (Green) CLEAN LED (Amber) FAULT LED (Amber right)
LED-test.
The LEDs are turned ON one-by-one.
Power-On Self-Test starts in parallel
with the LED-test .
ON ON ON ON
Cartridge not loaded. OFF OFF ON / OFF OFF
Cartridge loaded, no activity ON OFF ON / OFF OFF
Cartridge loaded, activity ON Flashing ON / OFF OFF
Cleaning OFF Flashing ON OFF
Cartridge loading or unloading OFF Flashing ON / OFF OFF
Unrecoverable drive failure ON / OFF OFF ON / OFF Flashing
Over temperature OFF OFF ON / OFF ON
Media Error (wrong, write protected or
harmed media) OFF Flashing ON / OFF Flashing
Table 2 Front LED behavior during normal operation

6
Media and Capacities
To achieve and maintain the maximum quality of your Tandberg Data tape drive,
we recommend using Tandberg Data media.
Drive
Model Media Name Tape Length Capacity (Native) Ordering no.
43 26 30Tandberg
220LTO LTO Ultrium Generation 1 (Native format) 609 m 100 GByte
43 27 44Tandberg
420LTO LTO Ultrium Generation 2 (Native format) 609 m 200 GByte 43 26 30LTO Ultrium Generation 1 (Read/Write compatible) 609 m 100 GByte
43 26 31LTO1, 2, 3 Cleaning Cartridge for LTO1, LTO2 and LTO3
Table 3 Media alternatives
External Tabletop Enclosure
Figure 6 External tabletop enclosure, rear side
ON/OFF Switch
Power Connector
Cooling Fan SCSI_ID Switch
SCSI Interface Connectors
Power Requirements
Tandberg 220/420LTO in external tabletop enclosure:
AC Input: 100 VAC / 0.6 A or 240 VAC / 0.3 A, 50-60 Hz
Tandberg 220/420LTO as standalone:
DC Input (typical operation): 5 VDC / 2.1 A, 12 VDC / 0.6 A
Heat Dissipation
Tandberg 220/420LTO as standalone:
Operating: 18 W
Sleep mode with cartridge inserted: 9 W

7
Total customer satisfaction is of the utmost importance
to Tandberg Data.
We guarantee that this product left our premises defect free.
If you are not satisfied with the quality of this product,
please contact your distributor or the nearest
Tandberg Data office to have the problem solved!
For more documentation and information, please see our website
www.tandberg.com.

Tandberg Data
International headquarter
Tandberg Data ASA, Kjelsåsveien 161, Oslo, P.O. Box 134 Kjelsås, N-0411 Oslo, Norway.
Tel: [phone]. Fax: [phone].
www.tandberg.com
Worldwide subsidiaries
Tandberg Data Corp., 13000 Gregg Street, Poway, CA 92064, U.S.A.
Tel: [phone]. Fax: [phone]
Tandberg Data GmbH, Feldstrasse 81, D-44141 Dortmund, Germany.
Tel: [phone]. Fax: [phone].
Tandberg Data S.A.S., 16/18 Ave. Morane-Saulnier, F-78941 Vélizy Cedex, France.
Tel: [phone].
Fax: [phone] (for technical support: 00800-07867243).
Tandberg Data (Asia) Pte. Ltd, 20 Bendemeer Road, #04-05 Cyberhub, Singapore 339914,
Tel: [phone]. Fax: [phone].
Tandberg Data (Japan) Inc., Eitaibashi Eco-Piazza Bldg. 8th floor 29-13, Shinkawa 1-chome,
Chuo-ku Tokyo 104-033, Japan
Tel: [phone]. Fax: [phone].
Tandberg Data Ltd., Bloxham Mill Business Centre, Barford Road, Bloxham, Banbury,
Oxfordshire, OX15 4FF, United Kingdom
Tel: [phone].
Specifications subject to change without notice. All trademarks are the property of their respective owners.
©2006 Tandberg Data ASA. All Rights reserved.
Part No. 433261-04. February 2006.