Taoglas EDGE ES10B User manual

Taoglas EDGE™ES10 - RTK Starter Kit with US LTE

ES-10-8-005-A 2
Taoglas EDGE™RTK Starter Kit
Next-generation IoT device
and software platform
User Guide
Contents
1. Introduction
3
1.1 What’s in the Box?
3
1.2 Support
3
2. Set Up
4
2.1 Device Startup
4
2.2 Account Setup
4
2.3 Activating your Device
5
2.4 Activating RTK Correction Services
7
3. Using the EDGE RTK Starter Kit
8
3.1 Device Overview
8
4. Using EDGE Insights
9
4.1 Insights Navigation
9
4.2 Device Management
10
4.3 Dashboard
11
4.4 Sensor Notification Rules
14
4.5 Add New Users
17
4.6 Support
17
5. Appendix
18
5.1 Insights Navigation
18
5.2 Security
18
5.3 Safety and Regulatory Requirements
18

ES-10-8-005-A 3
1. Introduction
The Taoglas EDGE™RTK Starter Kit with High Precision GNSS enables real time insights
and intelligence to help your enterprise save costs, increase revenue, and enhance
compliance. It is a next-generation IoT device with cellular, Bluetooth, and on-board
sensor capabilities with a cloud based connectivity and device management platform.
1.1 What’s in the Box?
1. Taoglas EDGE RTK Starter Kit with High Precision GNSS
2. Micro-USB Cable
3. USB Power Supply - US Version (Regional adapters supplied with other SKU’s)
4. Taoglas EDGE Insights Activation Card
1.2 Support
For technical support please contact iotsu[email protected]
1. Go to https://www.taoglas.com/product/taoglas-edge-rtk-starter-kit to access
a. Datasheet
b. User Guides

ES-10-8-005-A 4
Charger Status LED
USB Power LED
User LED
Power Button
2. Set Up
2.1 Device Startup
1. To power on the EDGE RTK Starter Kit press the Power Button once.
2. The EDGE RTK Starter Kit should be fully charged before use, using the provided
power supply. When you plug the EDGE RTK Starter Kit into the provided USB power
supply, the USB Power LED will illuminate. If the EDGE RTK Starter Kit requires
charging, the Charge Status LED will illuminate, otherwise the Charge Status
LED will remain off. The EDGE RTK Starter Kit is not intended to be charged
using a computer USB.
3. Once powered on and initialised, the User LED will flash white 3 times.
4. At this stage you can check the battery level by pressing the Power Button once.
The User LED will blink a number of times according to the battery level.
Find more information on this in the Device Overview section below.
5. The device will start uploading to EDGE Insights straight away. To view any uploaded
samples, you will need to register an account and activate your device on
locate.taoglas.com.
2.2 Account Setup
1. To create an EDGE Insights account for your EDGE RTK Starter Kit devices, navigate to
locate.taoglas.com and click on ‘Sign Up’.
2. Create a username and enter your details.

ES-10-8-005-A 5
3. Once your information has been submitted, you will need to confirm your registration by clicking the link sent to
the email address provided.
4. Upon clicking the link, a browser will open and you will be requested to create a password.
5. After entering and confirming your password, registration is now complete, proceed to device activation.
2.3 Activating your Device
1. Using the details registered in the sign up process, you will be required to login to the EDGE Insights platform in
order to register your EDGE RTK Starter Kit.
2. The first time you log in, you will receive a popup message notifying you that you have not activated any devices.
Click on the ‘Devices Page’ button on the pop up, this will direct you to the device list page.

ES-10-8-005-A 6
3. To activate your EDGE RTK Starter Kit, click ‘Activate New Device’ at the bottom of the page, a popup window will
request your EDGE RTK Starter Kit S/N and Activation Code. After entering these, click ‘Submit’ to finish the
activation process. The EDGE RTK Starter Kit S/N and Activation Code can be found on the card included in the
box.
4. After entering the EDGE RTK Starter Kit S/N and Activation Code, click ‘Submit’ to activate your EDGE RTK Starter
Kit.
5. The EDGE RTK Starter Kit will now be listed on the devices page, see an example of this below.
6. If device activation fails please contact Taoglas IoT support at iotsupp[email protected]

ES-10-8-005-A 7
2.4 Activating RTK Correction Service
1. Navigate to the locate.taoglas.com and log into your account, if you don’t have an account already, please see
Section 2.2.
2. Once logged in, go to the device list page by clicking devices at the top right of the screen.
3. On the device list page click on the edit icon( ) on the device you want to enable with RTK, this will load the
device edit page.
4. On the device edit page you will be able to input the correction service details under the device parameters
section.

ES-10-8-005-A 8
3. Using the EDGE RTK Starter Kit
3.1 Device Overview
The EDGE RTK Starter Kit has 2 buttons and 3 LED’s. See the diagram below for an overview of the LED’s and buttons.
•To power on the EDGE RTK Starter Kit, push the Power Button once. When the EDGE RTK Starter Kit is powered on
and has successfully initialised, the User LED will flash white 3 times in quick succession.
•To power off the EDGE RTK Starter Kit, hold the Power Button, while the EDGE RTK Starter Kit is powering down the
User LED will blink red continuously. The User LED will stop blinking when the EDGE RTK Starter Kit has completely
powered off.
•When you plug the EDGE RTK Starter Kit into the provided USB Power supply, the USB Power LED will illuminate. If
the EDGE RTK Starter Kit requires charging, the Charge Status LED will illuminate, otherwise the Charge Status LED
will remain off.
•Once powered, the EDGE RTK Starter Kit will automatically connect to EDGE insights to gather configuration
information. The EDGE RTK Starter Kit will continue to operate at the sampling and upload intervals set on EDGE
Insights, for more information on these intervals see Device Management Section.
•The EDGE RTK Starter Kit can be forced into making a connection with EDGE Insights outside of the upload interval
using either of the following methods:
•A single press of the Power Button, followed by a single press of the User Button will trigger the EDGE RTK
Starter Kit to connect to EDGE Insights and gather new configuration information.
•A single press of the Power Button, followed by a longer push of the User Button (more than 4 seconds) will
trigger the EDGE RTK Starter Kit to sample all configured sensors and upload them to EDGE Insights.
•The EDGE RTK Starter Kit uploads its battery level to EDGE Insights, however, the battery status can also be checked
by pushing the Power Button once. This will cause the User LED to flash red a number of times according to the
battery level, as per the table below:
20%
1 Flash
40%
2 Flashes
60%
3 Flashes
80%
4 Flashes
100%
5 Flashes

ES-10-8-005-A 9
4. Using EDGE Insights
4.1 Insights Navigation
1. When you login to your account, you will land on the Dashboard page. For instructions on activating an
EDGE RTK Starter Kit on your account, please refer to the Activating your Device section.
2. You can use the links on the top of EDGE Insights interface to navigate between your dashboard,
device list page and account management pages.
a. Dashboard will bring you to your dashboard where you can see all the sensor data uploaded by your
EDGE RTK Starter Kit.
b. Devices will bring you to your device list page, from here you can manage each of the devices you have
activated on your account.
c. Clicking on ‘Settings’ will display a dropdown with various account management options, including:
i. Add/edit Users
ii. Edit Device Notification Rules
iii. Edit Device Notification Groups
iv. Edit Device Notification Contacts
d. Clicking on ‘Support’ will display a dropdown with support links.
e. Clicking on ‘Username’ will display a dropdown with various account management options, including:
i. Changing your password
ii. Editing your account details
iii. Deleting your account
iv. Logging out of your account

ES-10-8-005-A 10
4.2 Device Management
1. You can edit the details for an individual device by clicking the edit icon( ) on the devices page.
2. This will direct you to the Edit Device page, from here you can amend the following:
a. Device Name, here you can enter a customized name for your EDGE RTK Starter Kit.
b. Address, here you can enter your address.
c. Upload Interval, this is the rate at which the EDGE RTK Starter Kit will upload recorded sensor samples to
EDGE Insights.
d. Upload Retries, in the event where the EDGE RTK Starter Kit fails to upload samples, this is the number of
times it will attempt to upload before backing off.