Tascam CD-200SB User manual

D01174820B
CD-200SB
CD / Solid State Player
OWNER'S MANUAL

2 TASCAM CD-200SB
IMPORTANT SAFETY PRECAUTIONS
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the litera-
ture accompanying the appliance.
The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclo-
sure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This appliance has a serial number located on the rear panel.
Please record the model number and serial number and
retain them for your records.
Model number
Serial number
This equipment complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause interference and
2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
INFORMATION TO THE USER
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accor-
dance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user
will be required to correct the interference at his own
expense.
CAUTION
Changes or modifications to this equipment not expressly
approved by TEAC CORPORATION for compliance could
void the user's authority to operate this equipment.
For U.S.A.
In North America use only on 120V supply.
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CE Marking Information
a) Applicable electromagnetic environment: E4
b) The average half-cycle r.m.s. inrush current
1. On initial switch-on : 0.4Arms
2. After a supply interruption of 5s : 0.14Arms
8For European Customers
Disposal of electrical and electronic equipment
(a) All electrical and electronic equipment should be disposed
of separately from the municipal waste stream via collection
facilities designated by the government or local authorities.
(b) By disposing of electrical and electronic equipment
correctly, you will help save valuable resources and prevent
any potential negative effects on human health and the
environment.
(c) Improper disposal of waste electrical and electronic
equipment can have serious effects on the environment
and human health because of the presence of hazardous
substances in the equipment.
(d) The Waste Electrical and Electronic Equipment (WEEE)
symbol, which shows a wheeled bin that has been crossed
out, indicates that electrical and electronic equipment must
be collected and disposed of separately from household
waste.
(e) Return and collection systems are available to end users. For
more detailed information about the disposal of old electrical
and electronic equipment, please contact your city office,
waste disposal service or the shop where you purchased the
equipment.
WARNING
This is a Class A product. In a domestic environment, this product
may cause radio interference in which case the user may be
required to take adequate measures.
For Canada
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN
ICES-003.CET
APPAREIL NUMERIQUE DE LA CLASSE B EST CONFORME A LA
NORME NMB-003 DU CANADA.

TASCAM CD-200SB 3
IMPORTANT SAFETY INSTRUCTIONS
• The apparatus draws nominal non-operating power
from the AC outlet with its POWER or STANDBY/ON
switch not in the ON position.
• The mains plug is used as the disconnect device, the
disconnect device shall remain readily operable.
• Caution should be taken when using earphones or
headphones with the product because excessive
sound pressure (volume) from earphones or
headphones can cause hearing loss.
• If you are experiencing problems with this product,
contact TEAC for a service referral. Do not use the
product until it has been repaired.
CAUTION
• Do not expose this apparatus to drips or splashes.
• Do not place any objects filled with liquids, such as
vases, on the apparatus.
• Do not install this apparatus in a confined space
such as a book case or similar unit.
• The apparatus should be located close enough to
the AC outlet so that you can easily grasp the power
cord plug at any time.
• If the product uses batteries (including a battery
pack or installed batteries), they should not be
exposed to sunshine, fire or excessive heat.
• CAUTION for products that use replaceable lithium
batteries: there is danger of explosion if a battery is
replaced with an incorrect type of battery. Replace
only with the same or equivalent type.
WARNING
• Products with Class I construction are equipped
with a power supply cord that has a grounding
plug. The cord of such a product must be plugged
into an AC outlet that has a protective grounding
connection.
8RACK-MOUNTING THE UNIT
Use the supplied rack-mounting kit to mount the unit in a
standard 19-inch rack, as shown below.
Remove the feet of the unit before mounting.
CAUTION
• Leave 1U of space above the unit for ventilation.
• Allow at least 10 cm (4 in) at the rear of the unit for
ventilation.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
9 Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A ground-
ing type plug has two blades and a third grounding
prong. The wide blade or the third prong are pro-
vided for your safety. If the provided plug does not
t into your outlet, consult an electrician for replace-
ment of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience recep-
tacles, and the point where they exit from the appa-
ratus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table
specied by the manufacturer, or sold with the appa-
ratus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

4 TASCAM CD-200SB
8CAUTIONS ABOUT BATTERIES
This product uses batteries. Misuse of batteries could
cause a leak, rupture or other trouble. Always abide by
the following precautions when using batteries.
• Never recharge non-rechargeable batteries. The
batteries could rupture or leak, causing fire or injury.
• When installing batteries, pay attention to the polarity
indications (plus/minus (+/–) orientation), and install
them correctly in the battery compartment as indicat-
ed. Putting them in backward could make the batteries
rupture or leak, causing fire, injury or stains around
them.
• When you store or dispose batteries, isolate their termi-
nals with insulation tape or something like that to prevent
them from contacting other batteries or metallic objects.
• When throwing used batteries away, follow the dispos-
al instructions indicated on the batteries and the local
disposal laws.
• Do not use batteries other than those specified. Do not
mix and use new and old batteries or different types of
batteries together. The batteries could rupture or leak,
causing fire, injury or stains around them.
• Do not carry or store batteries together with small
metal objects. The batteries could short, causing leak,
rupture or other trouble.
• Do not heat or disassemble batteries. Do not put them
in fire or water. Batteries could rupture or leak, causing
fire, injury or stains around them.
• If the battery fluid leaks, wipe away any fluid on the
battery case before inserting new batteries. If the
battery fluid gets in an eye, it could cause loss of
eyesight. If fluid does enter an eye, wash it out thor-
oughly with clean water without rubbing the eye and
then consult a doctor immediately. If the fluid gets on
a person’s body or clothing, it could cause skin injuries
or burns. If this should happen, wash it off with clean
water and then consult a doctor immediately.
• The unit power should be off when you install and
replace batteries.
• Remove the batteries if you do not plan to use the unit
for a long time. Batteries could rupture or leak, causing
fire, injury or stains around them. If the battery fluid
leaks, wipe away any fluid on the battery compartment
before inserting new batteries.
• Do not disassemble a battery. The acid inside the
battery could harm skin or clothing.
8CAUTIONS ABOUT LASER RADIATION
This product has been designed and manufactured according
to FDA regulations “title 21, CFR, chapter 1, subchapter J, based
on the Radiation Control for Health and Safety Act of 1968,” and
is classified as a class 1 laser product. There is no hazardous
invisible laser radiation during operation because invisible laser
radiation emitted inside of this product is completely confined
in the protective housings.
The label required in this regulation is shown at 1.
For U.S.A
1
Cautions:
• DO NOT REMOVE THE PROTECTIVE HOUSING USING A
SCREWDRIVER.
• USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
• IF THIS PRODUCT DEVELOPS TROUBLE, CONTACT YOUR
NEAREST QUALIFIED SERVICE PERSONNEL, AND DO NOT USE
THE PRODUCT IN ITS DAMAGED STATE.
Optical pickup
Type : SF-P101V
Manufacturer : Sanyo Electric Co.,Ltd.
Laser output : Less than 0.2 mW on the objective lens
Wavelength : 790 +/- 25nm
Standard : IEC60825-1: 2007
Safety Information

TASCAM CD-200SB 5
Contents
1 – Introduction ......................................................................7
Features..................................................................................7
Included items .....................................................................7
Conventions used in this manual..................................7
Trademarks............................................................................8
Precautions for placement ..............................................8
Power supply........................................................................ 8
Beware of condensation...................................................8
Cleaning the unit.................................................................8
SD cards and USB flash drives ........................................9
Handling precautions................................................. 9
About media that have been confirmed
for use with this unit ...................................................9
SD card/USB flash drive write-protection ...........9
Precaution regarding use
with Mac operating systems....................................9
About discs............................................................................9
Handling of compact discs ....................................... 9
2 – Names and functions of parts..........................10
Top panel .............................................................................10
Rear panel............................................................................12
Display...................................................................................13
Remote control unit (TASCAM RC-CD200SB)..........14
3 – Preparations....................................................................16
Making connections ........................................................16
Preparing the remote control.......................................17
Inserting batteries......................................................17
Replacing the batteries............................................17
Cautions about the use of batteries.................... 17
Cautions about using the remote control.........17
Loading a CD ......................................................................17
Inserting and removing SD cards ...............................18
Inserting SD cards ......................................................18
Removing SD cards....................................................18
SD card write-protection switches ......................18
Connecting and disconnecting USB flash drives ..19
Connecting USB flash drives..................................19
Disconnecting USB flash drives ............................19
Selecting the playback media......................................19
4 – Playback..............................................................................20
Playable media and files ................................................20
Folders and tracks on data CDs,
SD cards and USB flash drives ......................................20
Playback area .....................................................................21
Setting the playback area .......................................21
Playback modes.................................................................21
Selecting the playback mode................................22
Playback................................................................................22
Selecting a track................................................................23
Skipping to the next or previous track...............23
Selecting by track number .....................................23
Search forward and backward .....................................23
Folder playback
(data CDs/SD cards/USB flash drives).........................24
Setting the playback folder....................................24
Programmed playback....................................................24
Setting the program .................................................25
Checking the program.............................................26
Replacing a program track .....................................26
Adding more program tracks................................26
Clearing the program ...............................................26
Repeat playback................................................................27
Time and text information display .............................27
Pitch control (with CDs only).........................................28
Intro Check function ........................................................29
5 – Browsing ............................................................................30
Browsing folders and files..............................................30
6 – Direct folder function..............................................32
Saving direct folder settings.........................................32
Assigning direct folders..................................................32
Assigning direct folders individually ..................33
Automatically assign all direct folders
(AUTO SET)....................................................................33
Changing individual direct folder assignments.....34
Direct folder playback ....................................................35
Setting the playback area with direct folders..35
Selecting the playback mode
with direct folders......................................................35
Using folder search/browse functions
during direct folder playback ................................36
Clearing direct folder assignments ............................36
Clearing individual direct folder assignments 36
Clearing all direct folder assignments
(CLEAR ALL) ..................................................................37
7 – Dubbing (copying) .....................................................38
Dubbing overview............................................................38
Dubbing ...............................................................................39
Dubbing using a 1–10/0 button that already has a
direct folder assignment ................................................40
Recording times when dubbing..................................41
8 – Erase folder function ...............................................42
Erasing folders....................................................................42

6 TASCAM CD-200SB
9 – Message Lists..................................................................43
Operation messages........................................................43
Warning messages ...........................................................43
Error messages...................................................................44
10 – Troubleshooting .......................................................45
11 – Specifications ..............................................................46
Ratings ..................................................................................46
Output ratings....................................................................46
Analog audio output ratings..................................46
Digital audio output ratings...................................46
Audio performance..........................................................46
Backup memory ................................................................46
General .................................................................................47
Dimensions .........................................................................47
8For China
产品有毒有害物质或元素的名称及含量
机种 ：CD-200SB 有毒有害物质或元素
品名 铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr6+)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
1CHASSIS 部份 ○ ○ ○ ○ ○ ○
2 FRONT PANEL 部份 ○ ○ ○ ○ ○ ○
3螺丝部份 ○ ○ ○ ○ ○ ○
4线材部份 ○ ○ ○ ○ ○ ○
5PCB Assy 部份 ×○○○○○
6 CD MECH 部份 ○ ○ ○ ○ ○ ○
7电源部份 ○ ○ ○ ○ ○ ○
8附属品部份 ×○○○○○
9LABEL 部份 ○ ○ ○ ○ ○ ○
10 包装部份 ○ ○ ○ ○ ○ ○
○ ：表示该有毒有害物质在该部件所有均质材料中的含有量均在 SJ/T11363-2006 标准规定的限量要求以下。
× ：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
（针对现在代替技术困难的电子部品及合金中的铅 )
Contents

TASCAM CD-200SB 7
1 – Introduction
Thank you for your purchase of the TASCAM CD-200SB CD / Solid
State Player.
Before connecting and using the unit, please take time to read
this manual thoroughly to ensure you understand how to
properly set up and connect the unit, as well as the operation
of its many useful and convenient functions. After you have
finished reading this manual, please keep it in a safe place for
future reference.
You can also download the Owner's Manual from the TASCAM
web site (http://tascam.com).
Features
• Plays back audio CDs (CD-DA) and data CDs (CD-ROM/R/
RW) with WAV, MP3 and MP2 format files.
• 2U rack mount size
• Plays back MP3, MP2, WAV, WMA and AAC format files on SD
cards and USB flash drives
• Analog (RCA and XLR) and digital (coaxial and optical)
outputs
• Headphone output with level control
• TASCAM RC-CD200SB remote control with number (1–10/0)
buttons included
• Displays textual information (artist name, album name,
track name, etc.) including CD text, ID3, WMA and AAC tags.
• 4 playback modes (continuous, single, random and
program)
• Repeat playback function can be turned ON and OFF
• Playback area can be designated (
ALL PLAY , FOLDER ) for
data CDs, SD cards and USB flash drives.
• CD playback pitch control function (±14%)
• Intro check function
• Time display options include track elapsed time, track
remaining time and total remaining time for audio CDs,
track elapsed time for data CDs and track elapsed time and
track remaining time for SD cards and USB flash drives
• CD drive has 10-second shockproof memory (protection
against skipping).
• CDs can be dubbed (copied) to SD cards and USB flash
drives
• Direct folder function using the number (1–10/0) buttons
on the main unit or the wireless remote control (SD card/
USB flash drive)
• Browse function (SD card/USB flash drive)
• Folder erase function (SD card/USB flash drive)
Included items
This product includes the following items.
Take care when opening the package not to damage the items.
Keep the packing materials for transportation in the future.
Please contact TASCAM if any of these items are missing or have
been damaged during transportation.
• Main unit ................................................................................................. 1
• Wireless remote control unit (RC-CD200SB)............................... 1
• AAA batteries......................................................................................... 2
• A rack-mounting screw kit................................................................ 1
• Warranty card ........................................................................................ 1
• Owner's Manual (this manual)......................................................... 1
Conventions used in this manual
In this manual, we use the following conventions:
• Buttons, connectors and other parts of the unit and external
devices are indicated like this: SET button
• Text displayed on the display of the unit and external
devices appears like this: ON .
• CD-DA format discs are sometimes called“audio CDs.”
• CDs that contain audio files in MP2, MP3 or WAV formats are
called “data CDs.”
• Audio CDs and data CDs are sometimes generically called
“CDs”.
• SD/SDHC memory cards are called “SD cards”.
• MP3, MP2, WAV, WMA and AAC files are sometimes
generically called “audio files”.
• The currently selected media is called the “current media”.
• The currently selected folder is called the“current folder”.
• The currently selected file is called the “current file”.
• Additional information is provided as necessary as tips,
notes and cautions.
TIP
These are tips about how to use the unit.
NOTE
These provide additional explanations and describe special
cases.
CAUTION
Failure to follow these instructions could result in injury, damage
to equipment or lost recording data, for example.

8 TASCAM CD-200SB
1 – Introduction
Trademarks
• TASCAM is a registered trademark of TEAC Corporation.
• SDHC Logo is a trademark of SD-3C, LLC.
• Supply of this product does not convey a license nor imply
any right to distribute MPEG Layer-3 compliant content
created with this product in revenue-generating broadcast
systems (terrestrial, satellite, cable and/or other distribution
channels), streaming applications (via Internet, intranets
and/or other networks), other content distribution systems
(pay-audio or audio-on-demand applications and the like)
or on physical media (compact discs, digital versatile discs,
semiconductor chips, hard drives, memory cards and the
like). An independent license for such use is required. For
details, please visit http://mp3licensing. com.
• MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
• This product is protected by certain intellectual property
rights of Microsoft. Use or distribution of such technology
outside of this product is prohibited without a license from
Microsoft.
• Other company names, product names and logos in this
document are the trademarks or registered trademarks of
their respective owners.
Precautions for placement
• The operating temperature should be between 5°C and
35°C (41°F and 95°F).
• Make sure that the unit is mounted in a level position for
correct operation.
• Do not place any object on the unit for heat dissipation.
• Avoid installing this unit on top of any heat-generating
electrical device such as a power amplifier.
Power supply
Connect the unit to the standard power outlet. Hold the plug
when connecting and disconnecting the power cord.
Beware of condensation
If the unit is moved from a cold to a warm place, or used
immediately after a cold room has been heated or otherwise
exposed to a sudden temperature change, condensation could
occur. Should this happen, leave the unit for one or two hours
before turning the unit on.
Cleaning the unit
To clean the unit, wipe it gently with a soft dry cloth. Do not
wipe with chemical cleaning cloths, paint thinner, ethyl alcohol
or other chemical agents to clean the unit as they could damage
the surface.
Once every five years, please contact the retailer where you
purchased the unit or a TASCAM service center for internal
cleaning. If the unit is not cleaned for a long time and dust is
allowed to accumulate inside it, fire or malfunction could result.
Cleaning is more effective when conducted before the humid
season. Please check with us about the cost of internal cleaning.

TASCAM CD-200SB 9
1 – Introduction
SD cards and USB flash drives
This unit can use SD cards and USB flash drives for playback and
dubbing.
A list of SD cards and USB flash drives that we have confirmed to
operate with this unit is posted on the TASCAM website (http://
tascam.com/)
Handling precautions
SD cards and USB flash drives are made with precision. In order
to avoid damaging SD cards and USB flash drives, please observe
the following precautions when handling them.
• Do not leave them in places that are extremely hot or cold.
• Do not leave them in places that are extremely humid.
• Do not get them wet.
• Do not place objects on top of them or twist them.
• Do not subject them to strong impacts.
• Do not remove or insert them during dubbing, playback or
data transfer or at other times they are being accessed by
the unit.
• When transporting them, do not leave their terminals
exposed (use covers).
About media that have been confirmed for
use with this unit
This unit uses SD cards and USB flash drives for playback and
dubbing.
Old SD cards and USB flash drives, as well as some new ones,
might have memory components with slow operating speeds or
small internal buffering capacities. Use of such cards and drives
could affect the dubbing performance of this unit.
Please refer to the list of SD cards and USB flash drives that
we have confirmed to operate with this unit that is posted on
the TASCAM website. You can also contact TASCAM customer
support. (http://tascam.com/)
SD card/USB flash drive write-protection
This unit writes settings used by the direct folder function (page
32) to the media in order to save them. Since direct folders
settings cannot be written to SD cards and USB flash drives that
are write-protected, these settings will be lost when the media is
removed and the power is turned OFF.
Precaution regarding use with Mac operating
systems
The number of songs and track numbers within a folder might
not match on SD cards and USB flash drives that have been
written on by a Mac. This is an existing problem with Mac system
files, but it will not affect playback on this unit.
If the “Trash” is not emptied on a Mac, the open space on an SD
card or USB flash drive could be insufficient and dubbing and
other operations might not be possible. Empty the Trash before
ejecting an SD card or USB flash drive from a Mac.
About discs
In addition to audio CDs (CD-DA), the CD-200SB can play
CD-R and CD-RW discs on which audio CD, MP3, MP2 or WAV
format files are recorded. The CD player can also play
3-inch CDs
Handling of compact discs
• Always place the compact discs in the trays with their label
facing upward.
• To remove a disc from its case, press down on the center of
the disc holder, then lift the disc out, holding it carefully by
the edges.
• Do not touch the signal side (the unlabeled side).Fingerprints,
oils and other substances can cause errors during playing.
• To clean the signal side of a disc, wipe gently with a soft dry
cloth from the center towards the outside edge. Dirt on discs
can lower the sound quality, so clean them and always store
them in a clean state.
• Do not use any record spray, anti-static solutions, benzine,
paint thinner or other chemical agents to clean CDs. This
could damage the delicate playing surface and cause CDs to
become unplayable.
• Do not apply labels or other materials to discs. Do not use
discs that have had tape, stickers or other materials applied
to their surface. Do not use discs that have sticky residue
from stickers, etc. Such discs could become stuck in the unit
or cause it to malfunction.
• Never use a commercially available CD stabilizer. Using stabi-
lizers with this unit will damage the mechanism and cause it
to malfunction.
• Do not use cracked discs.
• Only use circular compact discs. Do not use non-circular
promotional, etc. discs.
• Some record companies sell copy-protected discs or copy-
controlled discs that may not play back correctly in this unit.
Since such discs may not conform with the CD standard, do
not use them in this unit.
• If you experience problems with such non-standard discs,
you should contact the producers of the disc.

10 TASCAM CD-200SB
2 – Names and functions of parts
Top panel
1POWER switch
Press this switch to turn the unit on or off.
NOTE
• Before turning this unit’s power ON/OFF, minimize the
volume of monitoring systems connected to it.
• Do not wear headphones when turning the power ON/OFF.
Noise could damage speakers or your hearing.
2FOLDER/TRACK SELECT (1–10/0) buttons/indicators
When the TRK SEL indicator is not lit, these buttons can be
used for the direct folder function.
The indicators light on the buttons that have folders
assigned for the direct folder function. (See “Assigning direct
folders” on page 32.)
Press a button that has a lit indicator to begin playback of
the folder that has been assigned using the direct folder
function. During folder playback, the indicator blinks. (See
“Direct folder playback” on page 35.)
When the TRK SEL indicator is lit, these buttons can be used
as number (1–10/0) buttons to select track numbers on the
current media. (See “Selecting by track number” on page
23.)
Track numbers have a maximum of two digits on audio CDs
and a maximum of three digits on data CDs, SD cards and
USB flash drives.
3SET [AUTO SET] button/indicator
Use with the direct folder function to assign folders on an SD
card or USB flash drive to FOLDER/TRACK SELECT (1–10/0)
buttons. This indicator lights during assignment. (See
“Assigning direct folders”on page 32.)
Press this button while pressing and holding the DISPLAY
[SHIFT] button to automatically assign folders on the SD
card/USB flash drive to the FOLDER/TRACK SELECT (1–10/0)
buttons that have not yet been assigned. This indicator
blinks when the direct folder AUTO SET function is in use. (See
“Automatically assign all direct folders (AUTO SET)” on page
33.)
4CLEAR [CLEAR ALL] button/indicator
Use with the direct folder function to clear FOLDER/TRACK
SELECT (1–10/0) button folder assignments. This indicator
lights while clearing an assignment. (See “Clearing individual
direct folder assignments” on page 36.)
Press this button while pressing and holding the DISPLAY
[SHIFT] button to clear all FOLDER/TRACK SELECT (1–10/0)
buttons folder assignments. This indicator blinks while
clearing all assignments. (See “Clearing all direct folder
assignments (CLEAR ALL)”on page 37.)
5DUBBING [WAV/MP3] button/indicator
Use when dubbing (copying) from a CD to an SD card or
USB flash drive. This indicator lights while dubbing. (See “7 –
Dubbing (copying)”on page 38.)
Press this button while pressing and holding the DISPLAY
[SHIFT] button to show the current recording format setting
used when dubbing for two seconds. Press this button again
while pressing and holding the DISPLAY [SHIFT] button
during this time to change the setting. (See “Dubbing” on
page 39.)
6Disc tray
Insert discs (CD, CD-R, CD-RW) here.
7OPEN/CLOSE button
Use to open and close the disc tray.
8PLAY/PAUSE button
Press during playback to pause. When playback is stopped or
paused, press to start playback.
When in browse mode, use to confirm the selected track and
to start playback.
9STOP button
Press to stop playback.
While editing a program, press to clear all the program
entries. (See “Setting the program”on page 25.)
0SEARCH m/,[.//, SELECT 5/b]buttons
When in browse mode, use these to change the selection.
(See “5 – Browsing” on page 30.)
qPHONES jack and knob
Use this standard stereo jack to connect stereo headphones.
Use a plug adapter when connecting headphones with
mini-plugs. Use the PHONES knob to adjust the headphone
output level.
CAUTION
Use the PHONES knob to minimize the volume before connecting
headphones. Failure to do so could cause a sudden burst of loud
noise, which might result in hearing damage, for example.