Task Lighting T1 User manual

LED SPECIALISTS
Wall Mounted Touch Panel
T1, T2, T3, T4
Features
• Touch panel single colour, dual colour, RGB or RGBW PWM constant voltage controller
• Ultra sensitive high strength glass touch panel with touch colour wheel in the middle and back lighting
• Compatible with our wireless 2.4G remote range
• Touch keys with chord tones and LED indicator
Technical Parameters
Glass panel/Touch colour wheel/DC input/4 channel constant voltage PWM output/Wireless remote control
LVD
User Manual Ver 1.0.5
Technical Parameters
Model No.: T1, T2, T3, T4
Features
Page 1
1-4 color/Glass panel/Touch color wheel/DC input/4 channel constant voltage PWM output/Wireless remote control
W all Mounted Touch Panel
Touch panel single color, dual color, RGB or RGBW PWM constant voltage controller.
Ultra sensitive high strength glass touch panel with touch color wheel in the middle and backlighting.
Skydance’s 2.4G single zone or multiple zone remote controlCompatibility with .
Touch keys with chord tones and LED indicator.
Input and Output
Output type Constant voltage
Output power 144-288W
Output voltage 4 x (12-24)VDC
Output current 4CH,3A/CH
Input voltage 12-24VDC
Input current 12.5A
Light type Single colour Dual colour RGB
Constant voltage
144-288W
4 x (12-24)VDC
4CH,3A/CH
12-24VDC
12.5A
Constant voltage
144-288W
3 x (12-24)VDC
3CH,4A/CH
12-24VDC
12.5A
Model LCDMSD-T1 LCDMSD-T2 LCRGBSD-T3
Operation temperature
Case temperature (Max.)
Environment
IP20
IP rating
Ta: -30
O
C ~ +55
O
C
Tc:
+85
O
C
W arranty and Protection
5 years
Protection Reverse Polarity
Warranty
Safety and EMC
EMC standard (EMC) EN301 489,EN 62479
Radio Equipment(RED) EN300 328
Certification CE,EMC,LVD,RED
EN60950
Safety standard(LVD)
T1 T2 T3
T1,T2,T3,T4 Wall Mounted Touch Panel
T4
•LCDMSD-T1 Single colour panel
•LCDMSD-T2 Dual colour panel
Turn on/off light.
Dynamic mode, 6 level speed.
Brightness,10 levels.
Turn off light after 20s.
Brightness wheel.
Colour wheel.
Adjust dynamic mode speed,10 levels.
Adjust dynamic mode speed or static colour brightness,10 levels.
Note: After touch power key to turn off light, long press power key for 5 seconds will turn on or turn off tone.
Short press play 10 built-in dynamic mode, long press 2s run mode-cycle.
4 Scenes, short press recall scene.
Long press 2s to save the current colour into 1/2/3/4.
Power
20S
Delay Off
Mode
Bright
S P E E D
B R I GHT
MODE
P OWE R
WH IT E
B L UEGR E E N
R E D
S CE NE S CE NE S CE NE S CE NE
B RT /S P E E DMODE
Power
Mode
Bright
20S
Delay Off
Power
Mode
Turn on/off light.
Dynamic mode, 6 level speed.
Turn on/off light.
Brightness,10 levels.
Power
Mode
Bright
S P E E D
S CE NE S CE NE S CE NE SCENE
WHITE
B L UEGR E E N
R E D
Turn on/off light.
Mode
Short press play 10 built-in dynamic mode, long press 2s run mode-cycle.
B RT /S P E E D
Colour wheel.
Short press get red, green, blue, white colour,
long press adjust each colour brightness.
RGBW
Constant voltage
144-288W
4 x (12-24)VDC
4CH,3A/CH
12-24VDC
12.5A
LCRGBWSD-T4
Key function
MODE
POWER
BRIGHT
BRIGHT
Brightness +,10 levels.
Brightness -,10 levels.
Colour temperature wheel.
+
Weight
0.118kg
Gross weight
Net weight
0.230kg
• LCRGBSD-T3 RGB panel
• LCRGBWSD-T4 RGBW panel
LCDMSD-T1-B (black)
LCDMSD-T1-W (white)
LCDMSD-T2-B (black)
LCDMSD-T2-W (white)
LCRGBSD-T3-B (black)
LCRGBSD-T3-W (white)
LCRGBWSD-T4-B (black)
LCRGBWSD-T4-W (white)
Black
White
Black
White
Black
White
Black
White

Key Function
LVD
User Manual Ver 1.0.5
Technical Parameters
Model No.: T1, T2, T3, T4
Features
Page 1
1-4 color/Glass panel/Touch color wheel/DC input/4 channel constant voltage PWM output/Wireless remote control
W all Mounted Touch Panel
Touch panel single color, dual color, RGB or RGBW PWM constant voltage controller.
Ultra sensitive high strength glass touch panel with touch color wheel in the middle and backlighting.
Skydance’s 2.4G single zone or multiple zone remote controlCompatibility with .
Touch keys with chord tones and LED indicator.
Input and Output
Output type Constant voltage
Output power 144-288W
Output voltage 4 x (12-24)VDC
Output current 4CH,3A/CH
Input voltage 12-24VDC
Input current 12.5A
Light type Single colour Dual colour RGB
Constant voltage
144-288W
4 x (12-24)VDC
4CH,3A/CH
12-24VDC
12.5A
Constant voltage
144-288W
3 x (12-24)VDC
3CH,4A/CH
12-24VDC
12.5A
Model LCDMSD-T1 LCDMSD-T2 LCRGBSD-T3
Operation temperature
Case temperature (Max.)
Environment
IP20
IP rating
Ta: -30
O
C ~ +55
O
C
Tc: +85
O
C
W arranty and Protection
5 years
Protection Reverse Polarity
Warranty
Safety and EMC
EMC standard (EMC) EN301 489,EN 62479
Radio Equipment(RED) EN300 328
Certification CE,EMC,LVD,RED
EN60950
Safety standard(LVD)
T1 T2 T3
T1,T2,T3,T4 Wall Mounted Touch Panel
T4
•LCDMSD-T1 Single colour panel
•LCDMSD-T2 Dual colour panel
Turn on/off light.
Dynamic mode, 6 level speed.
Brightness,10 levels.
Turn off light after 20s.
Brightness wheel.
Colour wheel.
Adjust dynamic mode speed,10 levels.
Adjust dynamic mode speed or static colour brightness,10 levels.
Note: After touch power key to turn off light, long press power key for 5 seconds will turn on or turn off tone.
Short press play 10 built-in dynamic mode, long press 2s run mode-cycle.
4 Scenes, short press recall scene.
Long press 2s to save the current colour into 1/2/3/4.
Power
20S
Delay Off
Mode
Bright
S P E E D
B R I GHT
MODE
P OWE R
WH IT E
B L UEGR E E N
R E D
S CE NE S CE NE S CE NE S CE NE
B RT /S P E E DMODE
Power
Mode
Bright
20S
Delay Off
Power
Mode
Turn on/off light.
Dynamic mode, 6 level speed.
Turn on/off light.
Brightness,10 levels.
Power
Mode
Bright
S P E E D
S CE NE S CE NE S C E NE SCENE
WHITE
B L UEGR E E N
R E D
Turn on/off light.
Mode
Short press play 10 built-in dynamic mode, long press 2s run mode-cycle.
B RT /S P E E D
Colour wheel.
Short press get red, green, blue, white colour,
long press adjust each colour brightness.
RGBW
Constant voltage
144-288W
4 x (12-24)VDC
4CH,3A/CH
12-24VDC
12.5A
LCRGBWSD-T4
Key function
MODE
POWER
BRIGHT
BRIGHT
Brightness +,10 levels.
Brightness -,10 levels.
Colour temperature wheel.
+
Weight
0.118kg
Gross weight
Net weight
0.230kg
• LCRGBSD-T3 RGB panel
• LCRGBWSD-T4 RGBW panel
Note: After touch power key to turn off light, long press power key for 5 seconds will turn on or turn off tone.

Wiring Diagram
User Manual Ver 1.0.5 Page 2
LED power supply voltage and power select :
12V lamp, Input 12V power supply, can load 0~144W,
24V lamp, Input 24V power supply, can load 0~288W, The power supply power must larger than load power 20%.
T 1
Pow er S upply
12-24VDC
Constant Voltage
+
Single colour LED strip
+
Single colour LED strip
+
Single colour LED strip
+
Single colour LED strip
+
CW
WW Dual colour LED strip
Pow er S upply
12-24VDC
Constant Voltage
+
CW
WW Dual colour LED strip
T 2
RGB LED strip
Pow er S upply
12-24VDC
Constant Voltage
T 3
RGBW LED strip
Pow er S upply
12-24VDC
Constant Voltage
T 4
W
A C100-240V
A C100-240V
A C100-240V
A C100-240V
W iring diagram
T1,T2,T3,T4 Wall Mounted Touch Panel
Match Remote Control (two match ways)
Use Power Restart
Match:
Switch off the power, then switch on power again,
immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
.
Delete:
Switch off the power, then switch on power again,
immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were
deleted.
The touch panel controller can also match with the RF remote (optional).
End user can choose the suitable match/delete ways. Two options are offered for selection:
Mechanical Structures and Installations
86mm
86mm
59mm
45.5mm
Typical base as below:
European style
Baseplate Base
Uninstall
Installation diagram:
11.5mm
62mm
35mm 86 size
Touch panel
Use On/Off key
Match:
Turn on light, turn off, immediately press the On/Off
key of the panel for 5s, then press on/off key
(single zone remote) or zone key (multiple zone remote)
of the RF remote within 5s.
Delete:
Turn on light, turn off, immediately press the On/Off
key of the panel for 10s, delete all matched RF remote.
RGB/ RGBW d ynamic mode list (only for T3 / T 4)
No. N ame No. Name
RGB jump
RGB smooth
6 color jump
6 color smooth
Yellow cyan purple smooth
RGB fade in and out
Red fade in and out
Green fade in and out
Blue fade in and out
White fade in and out
1
2
3
4
5
6
7
8
9
10
• LCDMSD-T1 Single Colour Panel
• LCDMSD-T2 Dual Colour Panel
• LCRGBSD-T3 RGB Panel
• LCRGBWSD-T4 RGBW Panel
LED power supply voltage and power select:
• 12V lamp, Input 12V power supply, can load 0~144W,
• 24V lamp, Input 24V power supply, can load 0~288W, The power supply power must larger than load power 20%.

While every effort has been made to ensure the accuracy of all information provided Task Lighting can not be held responsible for any errors. Task
Lighting also reserves the right to modify/delete product details without notice.
www.tasklighting.co.nz PH: 09 820 0004
Match Remote Control (two match ways)
The touch panel controller can also match with the RF remote (optional).
End user can choose the suitable match/delete ways. Two options are offered for selection:
Use On/Off key
Match:
Turn on light, turn off, immediately press the On/
Off key of the panel for 5s, then press on/off key
(single zone remote) or zone key (multiple zone
remote) of the RF remote within 5s.
Delete:
Turn on light, turn off, immediately press the On/
Off key of the panel for 10s, delete all matched
RF remote.
Use Power Restart
Match:
Switch off the power, then switch on power again, immediately short
press on/off key (single zone remote)
or zone key (multiple zone remote) 3 times on the remote. The light
blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power again, immediately short
press on/off key (single zone remote) or zone key (multiple zone
remote) 5 times on the remote. The light blinks 5 times means all
matched remotes were deleted.
RGB/RGBW dynamic mode list (only for T3 / T4)
Match Remote Control (two match ways)
Use Power Restart
Match:
Switch off the power, then switch on power again,
immediately short press on/of f key (single zone remote)
or zone key (multiple zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
.
Delete:
Switch off the power, then switch on power again,
immediately short press on/of f key (single zone remote)
or zone key (multiple zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were
deleted.
The touch panel controller can also match with the RF remote (optional).
End user can choose the suitable match/delete ways. Two options are offered for selection:
Mechanical Structures and Installations
86mm
86mm
59mm
45.5mm
Typical base as below:
European style
Baseplate Base
Uninstall
Installation diagram:
11.5m m
62mm
35mm 86 size
Touch panel
User Manual Ver 1.0.5 Page 2
LED power supply voltage and power select :
12V lamp, Input 12V power supply , can load 0~144W ,
24V lamp, Input 24V power supply , can load 0~288W , The power supply power must larger than load power 20%.
T 1-1
Power Supply
12-24VDC
Constant Voltage
+
Single colour LED strip
+
Single colour LED strip
+
Single colour LED strip
+
Single colour LED strip
+
CW
WW Dual colour LED strip
Power Supply
12-24VDC
Constant Voltage
+
CW
WW Dual colour LED strip
T 2-1
RGB LED strip
Power Supply
12-24VDC
Constant Voltage
T 3-1
RGBW LED strip
Power Supply
12-24VDC
Constant Voltage
T 4-1
W
AC100-240V
AC100-240V
AC100-240V
AC100-240V
Use On/Off key
Match:
Turn on light, turn off, immediately press the On/Off
key of the panel for 5s, then press on/of f key
(single zone remote)
or zone key (multiple zone remote)
of the RF remote within 5s.
Delete:
Turn on light, turn off, immediately press the On/Off
key of the panel for 10s, delete all matched RF remote.
Wiring diagram
T1-1 ,T2-1,T3 -1 ,T4-1 Wa ll M ounted Touch Panel
RGB/RGBW dynamic mode list (only for T3-1 / T4-1)
No. Name No. Name
RGB jump
RGB smooth
6 c olour jump
6 c olour smooth
Yellow cyan purple smooth
RGB fade in and out
Red fade in and out
Green fade in and out
Blue fade i n and out
White fade in and out
1
2
3
4
5
6
7
8
9
10
• LCDMSD-T1-1 Single Colour Panel
• LCDMSD-T2-1 Dual Colour Panel
• LCRGBSD-T3-1 RGB Panel
• LCRGBWSD-T4-1 RGBW Panel
Mechanical Structures and Installations
User Manual Ver 1.0.5 Page 2
LED power supply voltage and power select :
12V lamp, Input 12V power supply, can load 0~144W,
24V lamp, Input 24V power supply, can load 0~288W, The power supply power must larger than load power 20%.
T 1
Pow er S upply
12-24V DC
Constant Voltage
+
Single colour LED strip
+
Single colour LED strip
+
Single colour LED strip
+
Single colour LED strip
+
CW
WW Dual colour LED strip
Pow er S upply
12-24V DC
Constant Voltage
+
CW
WW Dual colour LED strip
T 2
RGB LED strip
Pow er S upply
12-24V DC
Constant Voltage
T 3
RGBW LED strip
Pow er S upply
12-24V DC
Constant Voltage
T 4
W
A C100 -24 0V
A C100 -24 0V
A C100 -24 0V
A C100 -24 0V
W iring diagram
T1,T2,T3,T4 Wall Mounted Touch Panel
Match Remote Control (two match ways)
Use Power Restart
Match:
Switch off the power, then switch on power again,
immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
.
Delete:
Switch off the power, then switch on power again,
immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were
deleted.
The touch panel controller can also match with the RF remote (optional).
End user can choose the suitable match/delete ways. Two options are offered for selection:
Mechanical Structures and Installations
86mm
86mm
59mm
45.5mm
Typical base as below:
European style
Baseplate Base
Uninstall
Installation diagram:
11.5mm
62mm
35mm 86 size
Touch panel
Use On/Off key
Match:
Turn on light, turn off, immediately press the On/Off
key of the panel for 5s, then press on/off key
(single zone remote) or zone key (multiple zone remote)
of the RF remote within 5s.
Delete:
Turn on light, turn off, immediately press the On/Off
key of the panel for 10s, delete all matched RF remote.
RGB/ RGBW d ynamic mode list (only for T3 / T 4)
No. N ame No. N ame
RGB jump
RGB smooth
6 color jump
6 color smooth
Yellow cyan purple smooth
RGB fade in and out
Red fade in and out
Green fade in and out
Blue fade in and out
White fade in and out
1
2
3
4
5
6
7
8
9
10
• LCDMSD-T1 Single Colour Panel
• LCDMSD-T2 Dual Colour Panel
• LCRGBSD-T3 RGB Panel
• LCRGBWSD-T4 RGBW Panel