Tasman Essential Tidy Drawer User manual

TM
TM
1
Essential Tidy Drawer
Assembly Instructions
Locking cams x 10
Castors x 5
Locking pins x 10
Base x 1
Side panels x 2
Rear panel x 1
Front panel x 1
Parts Checklist
Packaging and instructions
printed on recycled materials
RECYCLED
Tasman Eco Furniture Pty Ltd abn. 58 106 988 578
4-6 Merryvale Rd, Minto, NSW 2566 p.o. box 5878 Minto DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. [email protected]om.au w. www.tasmaneco.com.au
base support x 1
corner support x 4

Side panel
Back panel
2
Fit locking pins to front, back and side panels
Fit locking cams to the base support, side and back
panels.
Fit x 2 side panels and x 2 corner supports to back panel
Fit the base panel
-Lay the front, back and side panels face down on the oor
-Front panel - Screw x 5 locking pins into threaded holes, 2 at each end and one in the
middle
-Side panel - Screw x 2 locking pins into threaded holes on each side panel
-Back panel - Screw x 1 locking pin into threaded hole in the middle of the back panel
-Tighten all locking pins rmly
-Push each cam all the way into the hole. Use a screwdriver to
rotate the locking cams so the pointed end of the cross on the
cam points in the direction locking pins will insert from.
-Side panels - Insert x 2 cam locks into each side panel and rotate
to the correct positon
-Back panel - Insert x 4 cam locks into the back panel and rotate
to the correct position
-Base support - Insert x 2 cam locks into the base support and
rotate to the correct position
Note the pointed end of the cross on the cam locks must
point in the direction the lokcing pins will inserted from
Use a screwdriver to rotate cam
into correct alignment.
Repeat for each side panel
The corner support needs to be in positon in the back panel before
the side panel can be attached.
The corner support must be the correct way around with pro-
trudting plastic insert facing downwards.
- Hold the corner support in position against the back panel as per
the picture
- insert the locking pins on the side panel into the holes and cam
locks in the back panel
-Turn the cam locks with a screwdriver to lock them into the lock-
ing pins
- Repeat so both side panels are attached to the back panel
Slide the base into the grooves on the side panels and the
groove in the back panel.
1
2
3
4

3
Fit the base support to the back back panel
Fit corner supports and the front panel to assembled section
- Turn the assembled unit over being careful to keep the base in position
- Insert the base support into the back panel aligning the dowel and the locking pin
- Tighten the cam lock with a screwdriver to lock the base support in place
The corner support needs to be in positon in the side panel before the front panel can be attached.
- Stand assembled section upright
- Insert left hand side corner support to side panel of the assembled section and hold in position
- Place front panel on top of assembled section while continuing to hold corner support in posi-
tion, aligning the locking pins, with cam locks and dowel with hole
- When front panel is in position tighten left hand side cam locks.
- Repeat for the right hand side
Fit Castors
-Turn the assembled tidy drawer over.
-Fit x 5 castors, rmly pushing into castor inserts
TM
Turn the tidy drawer over and it is complete and ready to use.
Use a screwdriver to tighten the
cam locks
5
6
7

4
The Tasman Essentials Guarantee
100% Satisfaction Guarantee
If, within 3 months of the date of purchase of this product, the purchaser is not completely satised with this product for any reason, subject only to the
conditions below, the purchaser can return the product to the place of purchase or to SJC Brands Pty Ltd for a refund of the full purchase price of this
product.
Conditions.
The 100% Satisfaction Guarantee is void and nullied in circumstances where:
1. There are modications to the product or to parts of the product that were not authorised in writing by SJC Brands Pty Ltd.
2. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse or by use or storage
outside of the physical or environmental specications of the product.
5 Year Materials and Workmanship Guarantee
If within 5 years of the date of purchase of this product, there is found any defect in materials or workmanship of this product, SJC Brands Pty Ltd, will
replace the product free of charge, subject to the conditions below. The replacement product will be identical to the originally purchased product
wherever possible, though in situations where the identical model is discontinued or out of stock, then SJC Brands Pty Ltd will replace the product with a
model that is functionally equivalent.
This Guarantee is made to the purchaser and/or original owner only. For purposes of this Guarantee, the original owner is considered to be the person
who rst makes use of the product. Note: In situations where a person purchases this product for the purpose of gifting to another, the recipient is
considered to be the original owner.
Conditions.
The ‘5 Year Materials and Workmanship Guarantee’ will be void and nullied in circumstances where:
1. The item is improperly assembled or adjusted and or not assembled strictly in accordance with the written instructions provided by the seller in the
box containing the item.
2. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse or by use or storage
outside of the physical or environmental specications of the product.
3. There are modications to the product or to parts of the product that were not authorised in writing by SJC Brands Pty Ltd.
4. The item is transferred, gifted or disposed of by the original owner to another.
Registration and Claims
To be eligible for the above Guarantees, the original owner must register their details online at
www.tasmaneco.com.au immediately upon receipt of the product.
For claims under either the 100% Satisfaction Guarantee or the 5 year Materials and Workmanship Guarantee, please email us via our claims section on
our website at www.tasmaneco.com.au or visit the store where the product was purchased.
The product must be returned to SJC Brands Pty Ltd or to the place of purchase with proof of purchase, including date and purchase price.
Tasman Eco Furniture Pty Ltd abn. 58 106 988 578
4-6 Merryvale Rd, Minto, NSW 2566 p.o. box 5878 Minto DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. [email protected]om.au w. www.tasmaneco.com.au