TasmanEco Alfresco cot User guide

RECYCLED
TM
Assembly and care instructions
Mattress and accessories not included
Optional double bed rails and
base kit purchased separately
SJC Brands Pty Ltd abn. 58 106 988 578
4 Merryvale Road, MINTO, NSW 2566 p.o. box 5878 MINTO DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. [email protected]om.au w. www.tasmaneco.com.au
Alfresco cot
Packaging and instructions
printed on recycled materials
Cot
Bassinet
Junior Bed
Single Bed - Optional Kit
Chaise lounge
Save these instructions for future reference. Due to the heavy nature
of the cot, it is recommended assembly is undertaken by two people.
This cot can be assembled in a number of configurations.
Instructions for all configurations are included in this manual

2 3
Assembly tips - hardware
Wooden dowel pins
Connector bolts and lunar washers
Bolts
We recommend tightening all bolts and
connectors by hand. If using a cordless driver,
set the speed to a slow setting and the clutch
to a low setting to prevent excessive tightening
that may result in damage to your furniture.
Recheck tightness
Re-tighten all connector bolts (at least two months
after assembling the cot), as some connectors may
loosen as the cot settles. Periodically check all of the
connector bolts, making sure they are tight.
Gently push or tap dowel pins into place using
your thumb or a small hammer. Note, excessive
force may result in damage to the pin or furniture.
Insert the lunar washer into the locating hole, with
the curved face against the wall of the locating hole.
Insert the connector bolt into the washer and push
it through until it engages with the thread of the
insert on the panel you are attaching it to. Tighten
Warnings
Safety Consideration for your Child.
•Follow the manufacturer’s assembly instructions in detail to ensure the safety features of the cot are not compromised.
•ENSURE THE COT IS NOT PLACED TOO CLOSE TO HEATERS, BLINDS, CURTAINS, WINDOWS OR POWER POINTS.
•DO NOT HANG ANYTHING NEARBY WHERE THERE IS A POTENTIAL DANGER OF THE ITEM FALLING INTO THE COT.
•KEEP ANY MEDICATION, STRING, ELASTIC, SMALL TOYS OR SMALL ITEMS SUCH AS MONEY OUT OF REACH FROM
ANY POSITION IN THE COT. It is advisable to keep all items out of your child’s cot to prevent suffocation or strangulation.
•TO PREVENT FALLS, THE BASE OF THE COT SHOULD BE ADJUSTED TO THE LOWEST POSITION BEFORE YOUR
CHILD CAN SIT UP.
Recommended Mattress Size.
•This cot has been manufactured for use with a mattress which measures 750
mm (wide) x 1310 mm (long) x 120 mm (maximum thickness). The width and
mattress and the sides and ends of the cot do not exceed 40 mm. This is to
minimise the risk of a child’s limb becoming caught in the gap. The thickness
greater than 500 mm with the mattress base in the lower position to minimise
the risk of a child climbing or falling out of the cot.
Safety Consideration for Cot.
•Re-tighten all connector bolts (at least two months after assembling the cot), as some may loosen as the cot settles. Regularly
check all of the connecting bolts, making sure they are tight.
•Regularly check cot for weakness in timber joints and timber panels. If any weaknesses are found, report immediately to
Tasman Eco via: www.tasmaneco.com.au
•Do not use cot if it has been damaged in any way and always use genuine Tasman Eco parts. Contact your nearest Tasman Eco
stockist or original place of purchase for spare parts
•Report any fault with this furniture to Tasman Eco immediately. See website for details.
Small parts can present a choking hazard. Always keep small parts out of reach of children
both during and after assembly. Store any spare or unused parts in a safe place.
Side panels x 2
End panels x 2 Corner Post x 4 Extension Panel x 4
Base x 1
Major components & hardware
Single bed kits (Optional)
Warning
Care & cleaning tips
For general dusting / cleaning - periodically wipe the cot over with a dry soft cloth. To remove day to day
spills or dirt, wipe down with a soft cloth and mild solution of warm soapy water. Avoid scourers and steel
Bassinet Base x 1
Single bed bases x 2
Single Bed rail x 2
the connector bolt firmly but do not overtighten.

4 5
Assembly overview
Step 1-Attach support legs to end panels
Before commencing
assembly, note that
Alfresco cot can be
assembled as a full cot
with the base set in the
lower position; or as a
bassinet with the base
set in the high position.
Cot
Hardware needed
Step 2-Attach corner post to end panels
Hardware needed
A:M6 x 60mm connector bolts x 8
Step 3 -
Hardware needed
Cot / Bassinet - Assembly
A:Camlock x 4
B:Locking pin x 4
B:Camlock x 4
C:Locking pin x 4
A
B
Lay the end panel face down on the floor.
screw the locking pins(x2) into the threaded holes
Tighten firmly
Fit locking pins to end panels
1
2
3
Insert the camlock to support legs as shown.
Fit each support leg to the end panel as shown.
A
B
C
Use camlock and locking pins attached
support leg to corner post
M6 x 50mm Botls x 4
4 x lunar washers
M6 x 15mm cap bolts x 4
Fit the small cap bolts to the 4
remaining unused base holes
(2 on each side).
A). Attach each end panel to the base. Note the
base position needed for either ‘cot ’ or ‘bassinet’
configurations
To secure the base rails:
Insert a lunar washer to the locating hole at each end
of the base rails and then insert the connector bolts
and lightly hand tighten each connector bolt.
Do not fully tighten the bolts at this time.
B).IMPORTANT SAFETY STEP
A
A
B
B
Attach the end panels to the base

6 7
Step 4 -
Step 5 - Tighten all connector screws
Assembly is now complete
To complete assembly,
tighten all connector
bolts around the cot.
but do not overtighten.
Attached side panels to cot ends
8 x 60mm connector bolts x 8
Hardware needed
Secure side panel to cot ends using 8x60mm connector bolts.
Assembly overview
Parts List
Hardware List ( Bassinet kit )
Bassinet - Assembly
M6 x 60 Bolts x 8 Self Tapping Screw x4 Brackets x 4M6 x 15 Cap Bolt x 8
Bassinet Base x 1
Small parts can present a choking hazard. Always keep small parts out of reach of children
both during and after assembly . Store any spare or unused parts in a safe place.
Warning
We recommend tightening all screws and connectors by hand. If using a cordless driver, set the
speed to a slow setting and the clutch to a low setting to prevent execessive tightening that may
result in damage to your furniture.
Recheck tightness
Re-tighten all connector screws (at least two months after assembling the cot), as some connectors
may loosen as the Periodically check all of the connector screws,
making sure they are tight.
cot settles.
Optional baby bassinet kit
End panels x 2 Corner Post x 4 Extension panel x 4
4 x double ended cap bolts
Tighten the bolts firmly

Hardware needed
8
Step 1 -Prepare the Extension panels
8 x 50mm connector bolts x 8
Hardware needed
8 x 50mm connector bolt x 8
4 x end cap screws
Attach the extension panels in pairs.
Secure each pair of the extension
panels using the 35mm
connector bolts and end caps.
Tighten the bolts firmly but
do not overtighten
Attach the end panels to the
sides using the 35mm connector
bolts and lightly hand tighten
each connector bolt.
Do not fully tighten the bolts just yet
x 4 each end
Step 2 - Attach the end panels to Extension panels

x 4
910
Step 1
Single Bed - Assembly
Optional single bed kit purchased separately
Hardware needed
A:Camlockx 4
B:Locking pin x 4
A
A
B
B
I
Fit locking pins to end panels
Fit locking cams to support leg2
Fit support legs to end panels
Step 2 -
x 4
x 4
M6 x 50mm connector blot x 8
8 x end cap screws
Hardware needed
Hardware needed
Step 3 - Attach the brackets
4 x Brackets
Attach each brackets into the hole
provided on each corner frame
Step 4 - Attach the bassinet base panel
4 x self tapping screw
.
Attach the extension panels to end panels.
Secure each pair of the end panels using
the 35mm connector bolts and end caps.
Tighten the bolts firmly but
do not overtighten.

11 12
Step 5 - Attach base frames as shown below:
Note: Do not cut the fabric
webbing that holds the slats
together.
Fit the lattice base frames
between the bed rails. To
secure the frames, stretch
the first and last slat of the over
the corresponding dowel pins.
Repeat this step for all
remaining sides.
Step 4 - Attach the bed rails to the corner post
Temporarily attach the
bed rails to the corner
posts, aligning the
dowel pins at the ends
of the bed rails with the
corresponding locating
holes on each corner post
Secure each corner
with the lunar washer
and connector bolts.
Lightly hand tighten all
initial assembly, fully
tighten all bolts but
do not overtighten.
Step 3 - Attach the corner posts to the end panels
Hardware needed
4 x 50mm connector bolts
4 x lunar washers
M6 x 20mm cap screw x 16
Hardware needed
A:M6 x 60mm connector bolt x 8
B:Camlock x 4 C:Locking pin x 4
A
B
C
Attach the corner posts to end panels.
Use canlocks and locking pins attached the
end panels as shown.
x 8
x 4
Step 6 - Tighten all connector bolts
Assembly is now complete
To complete assembly,
tighten all connector
bolts around the bed.
bolts first, then after
Tighten the bolts firmly
but do not overtighten.

13
Conversion is now complete
Converting the cot into a Chaise lounge/Junior bed
1. To convert your Tasman Eco cot into
a chaise lounge, begin by loosening the
connector screws around the cot (8 in total).
2. Remove the 4 connector bolts from the inner
front panel. (Store these parts in a safe place).
3. Gently spread the side frames apart and
carefully remove the inner front panel.
5. Fit the small cap bolts to the 4 unused
locating holes (2 on each bed head). This is
a required safety step to prevent the entry of
4. Re-tighten all the connector bolts
between the side frames and base.
(Do not overtighten).
Place a throw rug over the mattress, add a few
colourful pillows and your child has their very own
chaise lounge where they can read, rest or play.
these steps are best undertaken by two people.

TM
Would you like us to assemble your Tasman Eco furniture for you?
fact, we guarantee it. If there is any damage resulting from our assembly service - it’s automatically our responsibility. Service is
prompt, reliable, and friendly.
Booking
This service is available only in the Sydney metro area. For more information, including pricing, see our website www.tasmaneco.
com.au. Or just call 02-9603-5000 during business hours to arrange a time and a day, so one of our assembly professionals can
come to your home to assemble your newly purchased Tasman Eco furniture.
Furniture Assembly Service
Guarantee & Warranty
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
The guarantee described below is in addition to the guarantee provided by law.
100% Satisfaction Guarantee
subject only to the conditions below, the purchaser can return the product to the place of purchase or to SJC Brands Pty Ltd for a
refund of the full purchase price of this product.
Conditions.
1.
2. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse
5 Year Materials and Workmanship Warranty
If within 5 years of the date of purchase of this product, there is found any defect in materials or workmanship of this product, SJC
Brands Pty Ltd, will replace the product free of charge, subject to the conditions below. The replacement product will be identical to
the originally purchased product wherever possible, though in situations where the identical model is discontinued or out of stock,
then SJC Brands Pty Ltd will replace the product with a model that is functionally equivalent.
This Warranty is made to the purchaser and/or original owner only . For purposes of this Warranty, the original owner is
purpose of gifting to another, the recipient is considered to be the original owner.
Conditions.
3. The item is improperly assembled or adjusted and or not assembled strictly in accordance with the written instructions provided
by the seller in the box containing the item.
4. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse
5.
6. The item is transferred, gifted or disposed of by the original owner to another.
Registration and Claims
To be eligible for the above Guarantee & Warranty,the original owner must register their details online at www.tasmaneco.com.au
immediately upon receipt of the product. For claims under either the 100% Satisfaction Guarantee or the 5 year Materials and
Workmanship Warrranty, please email us via our claims section on our website at www .tasmaneco.com.au or visit the store
where the product was purchased. The product must be returned to SJC Brands Pty Ltd or to the place of purchase with proof of
purchase, including date and purchase price.
vogue_cot_ins_0315
SJC Brands Pty Ltd abn. 58 106 988 578
4 Merryvale Road, MINTO, NSW 2566 p.o. box 5878 MINTO DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. [email protected]om.au w. www.tasmaneco.com.au
warranty