TasmanEco Verona Cot User guide

RECYCLED
TM
Assembly and care instructions
Mattress and accessories not included
Optional double bed rails and
base kit purchased separately
SJC Brands Pty Ltd abn. 58 106 988 578
4 Merryvale Road, MINTO, NSW 2566 p.o. box 5878 MINTO DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. inf[email protected] w. www.tasmaneco.com.au
Verona Cot
Packaging and instructions
printed on recycled materials
This cot can be assembled in a number of congurations.
Instructions for all congurations are included in this manual.
Cot
Bassinet
Junior Bed Double Bed - Optional Kit
Save these instructions for future reference. Due to the heavy nature
of the cot, it is recommended assembly is undertaken by two people.

2
Assembly tips - hardware
Wooden dowel pins Connector screws and lunar washers
Screws
We recommend tightening all screws and
connectors by hand. If using a cordless driver,
set the speed to a slow setting and the clutch
to a low setting to prevent excessive tightening
that may result in damage to your furniture.
Recheck tightness
Re-tighten all connector screws (at least two
months after assembling the cot), as some
connectors may loosen as the cot settles.
Periodically check all of the connector screws,
making sure they are tight.
Gently push or tap dowel pins into place using
your thumb or a small hammer. Note, excessive
force may result in damage to the pin or furniture.
Insert the lunar washer into the locating hole, with
the curved face against the wall of the locating hole.
Insert the connector screw into the washer and push
it through until it engages with the thread of the
insert on the panel you are attaching it to. Tighten
the connector screw rmly but do not overtighten.
Warnings
Safety Consideration for your Child.
• Follow the manufacturer’s assembly instructions in detail to ensure the safety features of the cot are not compromised.
• ENSURE THE COT IS NOT PLACED TOO CLOSE TO HEATERS, BLINDS, CURTAINS, WINDOWS OR POWER POINTS.
• DO NOT HANG ANYTHING NEARBY WHERE THERE IS A POTENTIAL DANGER OF THE ITEM FALLING INTO THE COT.
• KEEP ANY MEDICATION, STRING, ELASTIC, SMALL TOYS OR SMALL ITEMS SUCH AS MONEY OUT OF REACH FROM
ANY POSITION IN THE COT. It is advisable to keep all items out of your child’s cot to prevent su󰀨ocation or strangulation.
• TO PREVENT FALLS, THE BASE OF THE COT SHOULD BE ADJUSTED TO THE LOWEST POSITION BEFORE YOUR
CHILD CAN SIT UP.
Recommended Mattress Size.
• This cot has been manufactured for use with a mattress which measures 750
mm (wide) x 1310 mm (long) x 120 mm (maximum thickness). The width and
length are specied because it is IMPORTANT that the gaps between the
mattress and the sides and ends of the cot do not exceed 40 mm. This is to
minimise the risk of a child’s limb becoming caught in the gap. The thickness
of the mattress has been specied to ensure that the depth of the cot is
greater than 500 mm with the mattress base in the lower position to minimise
the risk of a child climbing or falling out of the cot.
Safety Consideration for Cot.
• Re-tighten all connector bolts (at least two months after assembling the cot), as some may loosen as the cot settles. Regularly
check all of the connecting bolts, making sure they are tight.
• Regularly check cot for weakness in timber joints and timber panels. If any weaknesses are found, report immediately to
Tasman Eco via: www.tasmaneco.com.au
• Do not use cot if it has been damaged in any way and always use genuine Tasman Eco parts. Contact your nearest Tasman Eco
stockist or original place of purchase for spare parts
• Report any fault with this furniture to Tasman Eco immediately. See website for details.

3
Small parts can present a choking hazard. Always keep small parts out of reach of children
both during and after assembly. Store any spare or unused parts in a safe place.
Allen key / phillips
key x 1 each
55mm connector screws x 4
70mm connector screws x 8
Metal lunar washers x 4
Side panels x 2
Rear bed head
x 1 (tall)
Front bed head
x 1 (short)
Base x 1
Lattice bed bases x 2
Major components & hardware
Double bed kit (optional)
Warning
15mm cap screws x 4
Wooden dowel pins x 830mm connector screws x 8
Bed rails x 2

4
Assembly overview
Before commencing
assembly, note that
Amore cot can be
assembled as a full cot,
with the base set in the
lower position; or as a
bassinet with the base
set in the high position.
Cot Bassinet
Cot / Bassinet - Assembly
Care & cleaning tips
For general dusting / cleaning - periodically wipe the cot over with a dry soft cloth. To remove day to day
spills or dirt, wipe down with a soft cloth and mild solution of warm soapy water. Avoid scourers and steel
wool as these will damage the nish. Always dry the cot after cleaning.

5
COT
BASSINET
Step 1 - Attach the side panels to the base
A). Attach each side panel
to the base. Note the
base position needed for
either ‘cot’ or ‘bassinet’
congurations.
To secure the base rails:
Insert a lunar washer to the
locating hole at each end
of the base rails and then
insert the connector screws
and lightly hand tighten each
connector screw.
Do not fully tighten the
screws at this time.
B). IMPORTANT SAFETY STEP
Fit the small cap screws to the 4
remaining unused base locating
holes (2 on each side). This is a
required safety step to prevent
the entry of small ngers into
these holes.
Hardware needed
4 x 55mm connector screws
4 x lunar washers
4 x 15mm cap screws
x4
A.
B.

6
Step 2 - Attach the rear (tall) bed head
Gently lower the base and side panel
assembly onto the bed head panel.
Align the connector holes on the side
panels with the locating holes on the
bed head.
Insert the connector screws and lightly
hand tighten the screws. Do not fully
tighten the screws at this time.
Gently lower the bed end
panel onto the cot assembly.
Align the connector holes
on the side panels with the
locating holes on the bed
end panel.
Insert the connector screws
and lightly hand tighten the
screws.
Hardware needed
x4
x4
4 x 70mm connector screws
Step 3 - Attach the front (short) bed head
Hardware needed
4 x 70mm connector screws
Note orientation of back
panel - at side must
face inwards

7
Step 4 - Tighten all connector screws
Assembly is now complete
To complete assembly,
tighten all 12 connector
screws:
4 on the base / side
panels. 4 on the rear
bed head, and 4 on the
front bed head.
Tighten the screws
rmly but do not
overtighten.
Gently ip the cot into
the upright position.
Re-tighten all connector screws (at least two months after
assembling the cot), as some connectors may loosen
as the cot settles. Periodically check all of the connector
screws, making sure they are tight.

8
Note orientation
of bed head
Step 1 - Attach the bed rails to the bed heads
Hardware needed
8 x 30mm connector screws
Align the holes on
the brackets with the
locating holes on the
bed head frames.
Secure the brackets
to the frames with the
connector screws.
Lightly hand tighten all
screws rst, then after
initial assembly, fully
tighten all screws.
Do do not overtighten.
Double Bed - Assembly
Optional double bed kit purchased separately
Step 2 - Insert dowel pins to bed rails
Hardware needed
8 x wooden dowel pins
Insert the wooden
dowel pins as shown.

9
Step 3 - Attach base frames
Unfurl the lattice base frames.
Note: Do not cut the fabric webbing that
holds the slats together.
Fit the lattice base frames between the
bed rails.
To secure the frames, stretch the
rst and last slat of the over the
corresponding dowel pins.
Repeat this step for all remaining sides.
Stretch the rst and last slat of the
base frame over the dowel pins.
Do not cut the
fabric webbing
Step 4 - Insert cap screws
Hardware needed
IMPORTANT SAFETY STEP
Fit the small cap screws to the 4
remaining unused locating holes
(2 on each bed head). This is a
required safety step to prevent
the entry of small ngers into
these holes.
x4
4 x 15mm cap screws

10
Step 1 - Attach base to bed heads
Assembly is now complete
Attach each bed head to
the base.
To secure the base rails:
Insert a lunar washer to
the locating hole at each
end of the base rails and
then insert the connector
screws and tighten each
connector screw.
Junior Bed - Assembly
Hardware needed
4 x 55mm connector screws
4 x lunar washers

11

TM
Would you like us to assemble your Tasman Eco furniture for you?
It’s a great way to enjoy the benets of your furniture with a minimum of fuss. And you know the assembly will be done right - in
fact, we guarantee it. If there is any damage resulting from our assembly service - it’s automatically our responsibility. Service is
prompt, reliable, and friendly.
Booking
This service is available only in the Sydney metro area. For more information, including pricing, see our website www.tasmaneco.
com.au. Or just call 02-9603-5000 during business hours to arrange a time and a day, so one of our assembly professionals can
come to your home to assemble your newly purchased Tasman Eco furniture.
Furniture Assembly Service
The Tasmaneco Guarantee
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
The guarantee described below is in addition to the guarantee provided by law.
100% Satisfaction Guarantee
If, within 3 months of the date of purchase of this product, the purchaser is not completely satised with this product for any reason,
subject only to the conditions below, the purchaser can return the product to the place of purchase or to SJC Brands Pty Ltd for a
refund of the full purchase price of this product.
Conditions.
The 100% Satisfaction Guarantee is void and nullied in circumstances where:
1. There are modications to the product or to parts of the product that were not authorised in writing by SJC Brands Pty Ltd.
2. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse
or by use or storage outside of the physical or environmental specications of the product.
5 Year Materials and Workmanship Guarantee
If within 5 years of the date of purchase of this product, there is found any defect in materials or workmanship of this product, SJC
Brands Pty Ltd, will replace the product free of charge, subject to the conditions below. The replacement product will be identical to
the originally purchased product wherever possible, though in situations where the identical model is discontinued or out of stock,
then SJC Brands Pty Ltd will replace the product with a model that is functionally equivalent.
This Guarantee is made to the purchaser and/or original owner only. For purposes of this Guarantee, the original owner is
considered to be the person who rst makes use of the product. Note: In situations where a person purchases this product for the
purpose of gifting to another, the recipient is considered to be the original owner.
Conditions.
The ‘5 Year Materials and Workmanship Guarantee’ will be void and nullied in circumstances where:
3. The item is improperly assembled or adjusted and or not assembled strictly in accordance with the written instructions provided
by the seller in the box containing the item.
4. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse
or by use or storage outside of the physical or environmental specications of the product.
5. There are modications to the product or to parts of the product that were not authorised in writing by SJC Brands Pty Ltd.
6. The item is transferred, gifted or disposed of by the original owner to another.
Registration and Claims
To be eligible for the above Guarantees, the original owner must register their details online at www.tasmaneco.com.au
immediately upon receipt of the product. For claims under either the 100% Satisfaction Guarantee or the 5 year Materials and
Workmanship Guarantee, please email us via our claims section on our website at www.tasmaneco.com.au or visit the store
where the product was purchased. The product must be returned to SJC Brands Pty Ltd or to the place of purchase with proof of
purchase, including date and purchase price.
verona_dbl_cot_ins_1015
SJC Brands Pty Ltd abn. 58 106 988 578
4 Merryvale Road, MINTO, NSW 2566 p.o. box 5878 MINTO DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. inf[email protected] w. www.tasmaneco.com.au