TasmanEco Vogue Cot User guide

RECYCLED
TM
Assembly and care instructions
Mattress and accessories not included
Optional single bed rails, end
panel extensions and base kit
purchased separately
SJC Brands Pty Ltd abn. 58 106 988 578
4 Merryvale Road, MINTO, NSW 2566 p.o. box 5878 MINTO DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. [e-mail] w. www.tasmaneco.com.au
Vogue Cot
Packaging and instructions
printed on recycled materials
Cot
Bassinet
Junior Bed
Single Bed - Optional Kit
Chaise lounge
Save these instructions for future reference. Due to the heavy nature
of the cot, it is recommended assembly is undertaken by two people.

2
Warnings
Safety Consideration for your Child.
• Follow the manufacturer’s assembly instructions in detail to ensure the safety features of the cot are not compromised.
• ENSURE THE COT IS NOT PLACED TOO CLOSE TO HEATERS, BLINDS, CURTAINS, WINDOWS OR POWER POINTS.
• DO NOT HANG ANYTHING NEARBY WHERE THERE IS A POTENTIAL DANGER OF THE ITEM FALLING INTO THE COT.
• KEEP ANY MEDICATION, STRING, ELASTIC, SMALL TOYS OR SMALL ITEMS SUCH AS MONEY OUT OF REACH FROM
ANY POSITION IN THE COT. It is advisable to keep all items out of your child’s cot to prevent suffocation or strangulation.
• TO PREVENT FALLS, THE BASE OF THE COT SHOULD BE ADJUSTED TO THE LOWEST POSITION BEFORE YOUR
CHILD CAN SIT UP.
Recommended Mattress Size.
• This cot has been manufactured for use with a mattress which measures 750
mm (wide) x 1310 mm (long) x 120 mm (maximum thickness). The width and
mattress and the sides and ends of the cot do not exceed 40 mm.when the
mattress is pushed to one side or end,and 20mm when the mattress is centred
in the cot.The thickness of the mattress has been specified to ensure that the depth
of cot. greater than 500 mm with the mattress base in the lower position to minimise
the risk of a child climbing or falling out of the cot.
Safety Consideration for Cot.
• Re-tighten all connector bolts (at least two months after assembling the cot), as some may loosen as the cot settles. Regularly
check all of the connecting bolts, making sure they are tight.
• Regularly check cot for weakness in timber joints and timber panels. If any weaknesses are found, report immediately to
Tasman Eco via: www.tasmaneco.com.au
• Do not use cot if it has been damaged in any way and always use genuine Tasman Eco parts. Contact your nearest Tasman Eco
stockist or original place of purchase for spare parts
• Report any fault with this furniture to Tasman Eco immediately. See website for details.
Care & cleaning tips
For general dusting / cleaning - periodically wipe the cot over with a dry soft
cloth. To remove day to day spills or dirt, wipe down with a soft cloth and mild
solution of warm soapy water. Avoid scourers and steel wool as these will

3
Assembly tips - hardware
Wooden dowel pins
Connector screws and lunar washers
Screws
We recommend tightening all screws and connectors by hand. If using a cordless driver, set the
speed to a slow setting and the clutch to a low setting to prevent excessive tightening that may
result in damage to your furniture.
Recheck tightness
Re-tighten all connector screws (at least two months after assembling the cot), as some
connectors may loosen as the cot settles. Periodically check all of the connector screws, making
sure they are tight.
Gently push or tap dowel pins into place using
your thumb or a small hammer. Note, excessive
force may result in damage to the pin or furniture.
Insert the lunar washer into the locating hole, with
the curved face against the wall of the locating hole.
Insert the connector screw into the washer and push
it through until it engages with the thread of the
insert on the panel you are attaching it to. Tighten

4
Small parts can present a choking hazard. Always keep small parts out of reach of children
both during and after assembly. Store any spare or unused parts in a safe place.
Allen key x 1
Phillips style key may
also be needed for the
metal cross dowel
70mm connector screws x12 Metal cross dowels x 4Double ended cap screws x 8
Side panels x 2 End panels x 2
Base x 1
What you will need
Warning

5
60mm connector screws plus
end caps x 8
50mm connector screws x 12Cap screws x 8
15mm screws x 4
Extension panels x 4
Lattice bed bases x 2
Bed rails x 2
Lunar washers x 4
Single bed kit (optional)

6
COT
BASSINET
COT
BASSINET
Step 1 - Attach the base to one of the side panels
Attach the base to one
of the side panels.
Note the base position
needed for either ‘cot’ or
‘bassinet’.
Secure the base and
side panel at each
end with the connector
screws and metal cross
dowels.
Lightly hand tighten
each connector screw.
Do not fully tighten the
screws just yet.
Hardware needed
2 x 70mm connector screws
2 x metal cross dowels
x2
x2
Hint: For this step, hold the metal
cross dowel in place while you
insert the connector screw. Twist
the cross dowel around so that the
hole in the cross dowel lines up
with the screw.

7
Hardware needed
2 x 70mm connector screws
2 x metal cross dowels
4 x double ended cap screws
Step 2 - Attach the other side panel
Attach the remaining side
panel to the base. Again,
note the base position
needed for either ‘cot’ or
‘bassinet’. Choose the same
set of locating holes as the
other side panel.
Secure the base at each end
with the connector screws
and metal cross dowels as
before. Lightly hand tighten
each connector screw.
Do not fully tighten the
screws just yet.
IMPORTANT SAFETY STEP
Fit the double ended cap
screws to the 4 remaining
unused base locating holes
on the side panels.
(2 on each side)
This is a required safety step
to prevent the entry of small
Step 3 - Plug the unused holes
Hardware needed
x2
x4
x2

8
Step 4 - Attach the end panels
Step 5 - Tighten all connector screws
Assembly is now complete
Lightly loosen the
connector screws on
the base and sides to
allow the sides to be
gently spread apart.
Position the end
panels between the
corner posts at each
end of the cot.
Insert the connector
screws to each end
panel. Lightly hand
tighten the top 2
and then complete the
assembly by lightly
hand tightening the
bottom connector
screws.
To complete assembly,
tighten all connector
screws around the cot.
but do not overtighten.
Secure the top
Secure the bottom
screws last
Hardware needed
8 x 70mm connector screws

9
Step 1 - Attach the extension panels to the end panels
Step 2 - Attach the corner posts to the end panels
Attach the extension
panels to the end
panels.
Secure each panel
using the 60mm
connector screws and
end cap screws.
Tighten the screws
overtighten.
Attach the corner
posts to the end panel
assemblies. Note how
the corner posts are
facing.
Secure each post
using the 50mm
connector screws.
Tighten the screws
overtighten.
Hardware needed
Hardware needed
8 x 60mm connector screws
8 x end cap screws
8 x 50mm connector screws
x4 each end x4 each end
x4 each end
Single Bed - Assembly

10
Step 4 - Attach the lattice base frames
Unfurl the lattice base frames.
Note: Do not cut the fabric
webbing that holds the slats
together.
Fit the lattice base frames
between the bed rails. To
secure the frames, stretch the
the corresponding dowel pins.
slats of the base frame
over the dowel pins.
Do not cut the
fabric webbing
Step 3 - Attach the bed rails to the bed heads
Temporarily attach the
bed rails to the bed
heads.
To do this, align the
three wooden dowels
at the end of the bed
rails with the holes on
each corner post.
Secure each corner
with the lunar washer
and connector screw.
Lightly hand tighten all
screws at this stage.
Hardware needed
4 x 50mm connector screws
4 x lunar washers

11
8 x double ended cap screws
4 x 15mm cap screws
IMPORTANT SAFETY STEP
Fit the small cap screws and double
ended cap screws to the remaining
unused holes as shown. Repeat for each
corner of the bed. This is a required safety
into these holes.
Step 5 - Plug the unused holes
Hardware needed x4
x8
Step 6 - Tighten all connector screws
Assembly is now complete
To complete assembly,
tighten all connector
screws around the cot.
but do not overtighten.

12
Conversion is now complete
Converting the cot into a junior bed
1. To convert your Tasman Eco cot into a
junior bed, begin by loosening the connector
screws that hold the base in place. (4 in total)
2. Remove the connector screws from the front
and rear panels. (8 in total, store these parts in a
safe place).
3. Gently spread the side frames apart and
carefully remove the front and rear panels.
5. Fit the small cap screws to the 8 unused
locating holes (4 on each bed head). This is
a required safety step to prevent the entry of
4. Retighten all the connector screws between
the bed heads and base. (Do not overtighten).
these steps are best undertaken by two people.

13
Conversion is now complete
Converting the cot into a chaise lounge
1. To convert your Tasman Eco cot into
a chaise lounge, begin by loosening the
connector screws around the cot (8 in total).
2. Remove the 4 connector screws from the inner
front panel. (Store these parts in a safe place).
3. Gently spread the side frames apart and
carefully remove the inner front panel.
5. Fit the small cap screws to the 4 unused
locating holes (2 on each bed head). This is
a required safety step to prevent the entry of
4. Re-tighten all the connector screws
between the side frames and base.
(Do not overtighten).
Place a throw rug over the mattress, add a few
colourful pillows and your child has their very own
chaise lounge where they can read, rest or play.
these steps are best undertaken by two people.

Would you like us to assemble your Tasman Eco furniture for you?
fact, we guarantee it. If there is any damage resulting from our assembly service - it’s automatically our responsibility. Service is
prompt, reliable, and friendly.
Booking
This service is available only in the Sydney metro area. For more information, including pricing, see our website www.tasmaneco.
com.au. Or just call 02-9603-5000 during business hours to arrange a time and a day, so one of our assembly professionals can
come to your home to assemble your newly purchased Tasman Eco furniture.
Furniture Assembly Service
Guarantee & Warranty
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
The guarantee described below is in addition to the guarantee provided by law.
100% Satisfaction Guarantee
subject only to the conditions below, the purchaser can return the product to the place of purchase or to SJC Brands Pty Ltd for a
refund of the full purchase price of this product.
Conditions.
1.
2. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse
5 Year Materials and Workmanship Warranty
If within 5 years of the date of purchase of this product, there is found any defect in materials or workmanship of this product, SJC
Brands Pty Ltd, will replace the product free of charge, subject to the conditions below. The replacement product will be identical to
the originally purchased product wherever possible, though in situations where the identical model is discontinued or out of stock,
then SJC Brands Pty Ltd will replace the product with a model that is functionally equivalent.
This Warranty is made to the purchaser and/or original owner only . For purposes of this Warranty, the original owner is
purpose of gifting to another, the recipient is considered to be the original owner.
Conditions.
3. The item is improperly assembled or adjusted and or not assembled strictly in accordance with the written instructions provided
by the seller in the box containing the item.
4. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse
5.
6. The item is transferred, gifted or disposed of by the original owner to another.
Registration and Claims
To be eligible for the above Guarantee & Warranty,the original owner must register their details online at www.tasmaneco.com.au
immediately upon receipt of the product. For claims under either the 100% Satisfaction Guarantee or the 5 year Materials and
Workmanship Warrranty, please email us via our claims section on our website at www .tasmaneco.com.au or visit the store
where the product was purchased. The product must be returned to SJC Brands Pty Ltd or to the place of purchase with proof of
purchase, including date and purchase price.
SJC Brands Pty Ltd abn. 58 106 988 578
4-6 Merryvale Rd , Minto , NSW 2566 p.o. box 5878 Minto DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. customer.service
@sjcbrands.com.au
.w.www.tasmaneco.com.au .
warranty