TasmanEco Aspley Cot User guide

RECYCLED
TM
Assembly and care instructions
Save these instructions for future reference.
Mattress and
accessories
not included
SJC Brands Pty Ltd abn. 58 106 988 578
4 Merryvale Road, MINTO, NSW 2566 p.o. box 5878 MINTO DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. inf[email protected] w. www.tasmaneco.com.au
Aspley Cot
Packaging and instructions
printed on recycled materials
This cot can be assembled in a number of congurations. Instructions for all congurations are included in this manual.
Cot Bassinet Chaise Lounge Junior Bed

2
Thank you
Thank you for purchasing this Tasman Eco furniture.
Please attach any copies of receipts or other related product documents to this page for future reference.

3
Assembly tips - Hardware
Connector screws and lunar washers Screws
We recommend tightening all screws and
connectors by hand. If using a cordless driver,
set the speed to a slow setting and the clutch
to a low setting to prevent excessive tightening
that may result in damage to your furniture.
Recheck tightness
Re-tighten all connector screws (at least two
months after assembling the cot), as some
connectors may loosen as the cot settles.
Periodically check all of the connector screws,
making sure they are tight.
Insert the lunar washer into the locating hole, with
the curved face against the wall of the locating hole.
Insert the connector screw into the washer and push
it through until it engages with the thread of the
insert on the panel you are attaching it to. Tighten
the connector screw rmly but do not overtighten.
Warnings
Safety Consideration for your Child.
• Follow the manufacturer’s assembly instructions in detail to ensure the safety features of the cot are not compromised.
• ENSURE THE COT IS NOT PLACED TOO CLOSE TO HEATERS, BLINDS, CURTAINS, WINDOWS OR POWER POINTS.
• DO NOT HANG ANYTHING NEARBY WHERE THERE IS A POTENTIAL DANGER OF THE ITEM FALLING INTO THE COT.
• KEEP ANY MEDICATION, STRING, ELASTIC, SMALL TOYS OR SMALL ITEMS SUCH AS MONEY OUT OF REACH FROM
ANY POSITION IN THE COT. It is advisable to keep all items out of your child’s cot to prevent suffocation or strangulation.
• TO PREVENT FALLS, THE BASE OF THE COT SHOULD BE ADJUSTED TO THE LOWEST POSITION BEFORE YOUR
CHILD CAN SIT UP.
Recommended Mattress Size.
• This cot has been manufactured for use with a mattress which measures 750
mm (wide) x 1310 mm (long) x 120 mm (maximum thickness). The width and
length are specied because it is IMPORTANT that the gaps between the
mattress and the sides and ends of the cot do not exceed 40 mm. This is to
minimise the risk of a child’s limb becoming caught in the gap. The thickness
of the mattress has been specied to ensure that the depth of the cot is
greater than 500 mm with the mattress base in the lower position to minimise
the risk of a child climbing or falling out of the cot.
Safety Consideration for Cot.
• Re-tighten all connector bolts (at least two months after assembling the cot), as some may loosen as the cot settles. Regularly
check all of the connecting bolts, making sure they are tight.
• Regularly check cot for weakness in timber joints and timber panels. If any weaknesses are found, report immediately to
Tasman Eco via: www.tasmaneco.com.au
• Do not use cot if it has been damaged in any way and always use genuine Tasman Eco parts. Contact your nearest Tasman Eco
stockist or original place of purchase for spare parts
• Report any fault with the cot to Tasman Eco immediately. See website for details

4
Small parts can present a choking hazard. Always keep small parts out of reach of children
both during and after assembly. Store any spare or unused parts in a safe place.
Front and rear panels x 2 Side panels x 2
Base x 1
Major components & hardware
Warning
Allen key x 1
55mm connector screws x 12 15mm cap screws x 12
Metal lunar washers x 4

5
COT
BASSINET
COT
BASSINET
Assembly overview
Before commencing
assembly, note that
Aspley cot can be
assembled as a full cot,
with the base set in the
lower position; or as a
bassinet with the base
set in the high position.
Cot Bassinet
Step 1 - Attach the side panels to the base
A). Attach each side panel to
the base. Note the base position
needed for either ‘cot’ or ‘bassinet’
congurations.
To secure the base rails: Insert a lunar
washer to the locating hole at each
end of the base rails and then insert
the connector screws and lightly hand
tighten each connector screw.
Do not fully tighten the screws at this
time.
B). IMPORTANT SAFETY STEP
Fit the small cap screws to the 4
remaining unused base locating holes
(2 on each side). This is a required
safety step to prevent the entry of
small ngers into these holes.
Hardware needed
4 x 55mm connector screws
4 x 15mm cap screws
4 x lunar washers A.
B.
x4

6
Step 2 - Attach the front and rear xed panels
Gently spread the side panels
apart to allow sufcient
clearance for the xed panels
to placed in position without
damaging the surfaces of the
panels.
Note the correct orientation of
the panels; the metal badges
must face outwards on both
panels.
Position the xed panel
between the side frames and
align the locating holes for the
connector screws.
Insert the connector screws
to both ends of the xed
panel. Lightly hand tighten the
connectors screws - but do not
fully tighten at this time.
Repeat the above steps for the
remaining panel.
Hardware needed
x8
8 x 55mm connector screws
Note the correct
orientation of the
panels; The metal
badge must face
outwards on both
panels.

7
Step 3 - Tighten all connector screws
To complete assembly, tighten
all 12 connector screws; 4 on
the base and 4 on each of the
front and rear panels.
Tighten the screws rmly but do
not overtighten.
Assembly is now complete
Care & cleaning tips
For general dusting / cleaning - periodically wipe the cot over with a dry soft cloth. To remove day to day
spills or dirt, wipe down with a soft cloth and mild solution of warm soapy water. Avoid scourers and steel
wool as these will damage the nish. Always dry the cot after cleaning.

8
x12
Conversion is now complete
Converting the cot into a junior bed
1. To convert your Tasman Eco cot into
a junior bed, begin by loosening all the
connector screws around the cot. (12 in total)
2. Remove the connector screws from the front
and rear panels. Store these parts in a safe place.
3. Gently spread the side frames apart and
carefully remove the front and rear panels.
5. Fit the small cap screws to the unused
locating holes (6 on each bed head). This is
a required safety step to prevent the entry of
small ngers into these holes.
4. Retighten all the connector screws between
the bed heads and base. (Do not overtighten).
To prevent damaging the nish of your cot, we recommend
these steps are best undertaken by two people.

9
Converting the cot into a chaise lounge
1. To convert your Tasman Eco cot into a chaise
lounge, begin by loosening all connector screws
around the cot (12 in total).
3. Carefully remove the front panel.
5. Fit the small cap screws to the unused locating
holes (4 on each side). This is a required safety
step to prevent the entry of small ngers into
these holes.
4. Retighten the connector screws.
(Do not overtighten).
Place a throw rug over the mattress, add a few
colourful pillows and your child has their very own
chaise lounge where they can read, rest or play.
x8
Conversion is now complete
To prevent damaging the nish of your cot, we recommend
these steps are best undertaken by two people.
2. Remove the connector screws from the front
panel. Store these parts in a safe place).

10
Notes

11
Notes

TM
Would you like us to assemble your Tasman Eco furniture for you?
It’s a great way to enjoy the benets of your furniture with a minimum of fuss. And you know the assembly will be done right - in
fact, we guarantee it. If there is any damage resulting from our assembly service - it’s automatically our responsibility. Service is
prompt, reliable, and friendly.
Booking
This service is available only in the Sydney metro area. For more information, including pricing, see our website www.tasmaneco.
com.au. Or just call 02-9603-5000 during business hours to arrange a time and a day, so one of our assembly professionals can
come to your home to assemble your newly purchased Tasman Eco furniture.
Furniture Assembly Service
The Tasmaneco Guarantee
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
The guarantee described below is in addition to the guarantee provided by law.
100% Satisfaction Guarantee
If, within 3 months of the date of purchase of this product, the purchaser is not completely satised with this product for any reason,
subject only to the conditions below, the purchaser can return the product to the place of purchase or to SJC Brands Pty Ltd for a
refund of the full purchase price of this product.
Conditions.
The 100% Satisfaction Guarantee is void and nullied in circumstances where:
1. There are modications to the product or to parts of the product that were not authorised in writing by SJC Brands Pty Ltd.
2. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse
or by use or storage outside of the physical or environmental specications of the product.
5 Year Materials and Workmanship Guarantee
If within 5 years of the date of purchase of this product, there is found any defect in materials or workmanship of this product, SJC
Brands Pty Ltd, will replace the product free of charge, subject to the conditions below. The replacement product will be identical to
the originally purchased product wherever possible, though in situations where the identical model is discontinued or out of stock,
then SJC Brands Pty Ltd will replace the product with a model that is functionally equivalent.
This Guarantee is made to the purchaser and/or original owner only. For purposes of this Guarantee, the original owner is con-
sidered to be the person who rst makes use of the product. Note: In situations where a person purchases this product for the
purpose of gifting to another, the recipient is considered to be the original owner.
Conditions.
The ‘5 Year Materials and Workmanship Guarantee’ will be void and nullied in circumstances where:
3. The item is improperly assembled or adjusted and or not assembled strictly in accordance with the written instructions provided
by the seller in the box containing the item.
4. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse
or by use or storage outside of the physical or environmental specications of the product.
5. There are modications to the product or to parts of the product that were not authorised in writing by SJC Brands Pty Ltd.
6. The item is transferred, gifted or disposed of by the original owner to another.
Registration and Claims
To be eligible for the above Guarantees, the original owner must register their details online at www.tasmaneco.com.au immediate-
ly upon receipt of the product. For claims under either the 100% Satisfaction Guarantee or the 5 year Materials and Workmanship
Guarantee, please email us via our claims section on our website at www.tasmaneco.com.au or visit the store where the product
was purchased. The product must be returned to SJC Brands Pty Ltd or to the place of purchase with proof of purchase, including
date and purchase price.
aspley_cot_ins_0315
SJC Brands Pty Ltd abn. 58 106 988 578
4 Merryvale Road, MINTO, NSW 2566 p.o. box 5878 MINTO DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. inf[email protected] w. www.tasmaneco.com.au