Tatung IOT-3352 User manual

Basic Equipment
IOT-3352 Gateway
2.4GHz Antenna
AC power adaptor

2
Tatung Confidential
(Hardware Specification)
Product Name A+
Processor AM3352 32-bit RISC, 600 MHz
Memory and
Storage
SDRAM Memory 512M Bytes Samsung K4B4 1646E-BCK0
Flash Memory NAND Flash : 512M Bytes (MLC) MT29F4 08ABADAWP:D
Communication
Wi-Fi IEEE 802.11 b/g/n (support AP / station mode )
Bluetooth (B 4.0 BLE) Wi-Fi module built in (BL Link: BL-R8723RD2)
L E (4G) USB Dongle (option: E3372h-510)
External I/O
Button Total 2 buttons: Software configurable
LED Indicator Total 3 LED indicators: 2 for blue color LED ; 1 for dual color –
Red/ Blue (Software configurable )
Power DC jack (ΦA: 2.1 mm ΦB: 5.5 mm)
Antenna 1 swivel antenna (Wi-Fi)
USB 2 (1 for 4 dongle), total 3A
RJ45 1 (analog interfaced sensor) (IEEE 802.3 10/100Mpbs)
Mechanical Case Dimension 6.97”/177mm(W) x 1.46”/37mm(H) x 4.53”/115mm(D)
Accessory Power adaptor DC power adaptor (12V, 2A)
Environmental
Operating emperature 32ºF/0ºC to 104ºF/40ºC
Storage emperature -10ºC/-14ºF to 60ºC/140ºF
Software Environment Linux V3.6 & drivers

3
Tatung Confidential
Software specification
Communication Wi-Fi IEEE 802.11 b/g/n (support AP / station mode )
Bluetooth (B 4.0 BLE) Support BT ATT profile and Android beacon
External I/O
Button Total 2 buttons: PIO Software configurable
LED Indicator Total 3LED indicators: 2 for blue color LED ; 1 for dual color –
Red/ Blue ( PIO Software configurable )
USB USB 2.0 standard driver (USB1: Host port ; USB2: Device port)
RJ45 Ethernet PHY
Firmware
Wi-Fi auto connection
Charge management
Service Check (MQTT Client、CoAP Server)
Software Specification

4
Tatung Confidential
Outlook
Alert indicator
ateway
Reset
Wi-Fi
Reset
Power indicator
Wi-Fi
indicator
Dimension:
6.97”/177mm(W) x 1.46”/37mm(H) x 4.53”/115mm(D)

5
Tatung Confidential
Button Function
ateway Reset Button Reset gateway
Wi-Fi Reset Button Reset Wireless
LED indicator Function
Power Indicator (mono) Blue LED stays on after startup is complete
Wi-Fi indicator (mono) Blue LED stays on after Wi-Fi is in AP and station mode
Alert Indicator (dual) ateway Alert: Red LED blink at 1Hz
Wi-Fi alert: RED LED blink at 5Hz
Function state: Blue LED stays on
按鍵與燈號
按鍵與燈號按鍵與燈號
按鍵與燈號(Button & LED Indicator):

6
Tatung Confidential
Installation
Connect the power adapter to the receptor on the rear panel of the DAP-1353 and then
plug the other end of the power adapter to a wall outlet or power strip. The power LED
will turn O to indicate proper operation.

NO. Antenna Type Model Name Gain (Peak)
1. Omni-Directional AN2400-5533RS 2.2 dBi
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This equipment has been tested and ound to comply with the limits or a Class B digital device, pursuant to Part 15 o the FCC Rules.
These limits are designed to provide reasonable protection against harm ul inter erence in a residential installation.
This equipment generates, uses and can radiate radio requency energy and, i not installed and used in accordance with the instructions, may cause
harm ul inter erence to radio communications. However, there is no guarantee that inter erence will not occur in a particular installation.
I this equipment does cause harm ul inter erence to radio or television reception, which can be determined by turning the equipment o and on, the user
is encouraged to try to correct the inter erence by one or more o the ollowing measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit di erent rom that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician or help.
This device complies with Part 15 o the FCC Rules. Operation is subject to the ollowing two conditions:
(1) This device may not cause harm ul inter erence, and
(2) this device must accept any inter erence received, including inter erence that may cause undesired operation.
CAUTION:
To assure continued FCC compliance:
Any changes or modi ications not expressly approved by the grantee o this device could void the user's authority to operate the equipment.
RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set orth or an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This radio transmitter (identi y the device by certi ication number or model number i Category II) has been approved by Industry Canada to operate with
the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated or that type, are strictly prohibited or use with this device.
Appendix