Taylor ESPRESSO Toy Storage Chest User manual

Quality Wooden Children’s Furniture and Accessories
• Please inspect the parts for damage during shipping and for any missing items. If you suspect that there may be damage or a shortage, contact us
and we will send replacement parts if needed.
• As soon as components and hardware are unpacked; please remove and recycle all plastic bags from possible contact with children.
• Words in Red represent a component or hardware used in assembly.
• Illustrations are intended to help identify components and hardware and are not drawn to scale.
Please read instructions carefully to
avoid accidental damage to
components during assembly.
Hardware
4- #8 5/8 in.
Wood Screws
12- Joint Connector Bolts
14- #5 5/8 in.
Wood Screws
1- Lid Support
Toy Storage Chest Components
Page 1 of 3
Tools needed for assembly
• Medium size #2 Phillips
Screwdriver
• Supplied Allen Wrench
Front
Back
Side
Side
Bottom
WARNING: ADULT ASSEMBLY REQUIRED
WARNING: Assembly kit contains parts with sharp points.
WARNING: Assembly kit contains parts with sharp edges.
WARNING: Package contains plastic bags that present suffocation risks for children.
WARNING: Assembly kit contains small parts that present choking hazards for children.
12- Barrel
Top
Bottom
Lid
Made in America
Toy Storage Chest Assembly Instructions; ESPRESSO

Quality Wooden Children’s Furniture and Accessories
Toy Stoprage Chest Assembly Instructions- Continued
• Insert a Barrel Nut into the Back panel
Barrel Nut hole in relation to the Joint
Connector Bolt previously installed.
• Make sure the longest slot on the head
of the Barrel Nut is perpendicular to
the Joint Connector Bolt.
• Fasten the Side panel and Back panel
together. Start Joint Connector Bolt by hand
and after a few turns begin using the supplied
Allen wrench.
• Make sure Back panel ts inside groove.
Tighten bolt to a snug t. Then unscrew one
full turn to allow adjustment.
• Now, repeat steps 1,2 and 3 for
second hole and to assemble
the other Side panel.
• Starting with a Side panel, insert one Joint
Connector Bolt in Joint Connector Bolt
hole.
• Repeat steps 1, 2 and 3 to attach
Front panel to body.
• With the box sitting at on a hard
surface, tighten all eight bolts.
Bottom Panel
Panel Groove
12 3
456
Page 2 of 3
• Using the existing holes, attach bottom of
Lid Support to inside of Back with 2 #8 screws
• Be careful not to over tighten screws.
• Place Lid on top of the box and line
up existing holes located on outside
of the back panel to holes in hinge.
Attach hinge to back of box using 14
#5 screws.
• Be careful not to over tighten screws.
Lid
Body
Back
Lid Support
Partial view of Back/Front panel
Barrel Nut Holes
Joint Connector
Holes
Side Panel
Top
Bottom
Area of Detail
Made in America
• Now that you have the two sides
fastened to the back; slide the
Bottom panel in the bottom grooves
(The side with the logo is the top
side).

• Open lid to approximately 85 degrees and hold it
in place. Mount the top part of the Lid Support to
the inside of the lid using 2 #8 screws.
• It is very important that the screws be started in
the indentations or the lid support may not function
properly
•Be careful not to over tighten screws.
Toy Storage Chest Assembly Instructions- Continued
Please Recycle Instructions
• Now that you have completed the assembly,
open and close the lid 10 times to break in the
lid support mechanism.
•The lid should not fall when the Lid Support is
properly installed.
• If the lid does not stay in position when raised,
please call us and we will help you. Until the lid
support is properly installed, do not allow
children to use this product. Please check the
lid support mounting screws periodically to
make sure they remain tight.
78
Page 3 of 3
Use and Care Instructions
WARNING
Failure to properly install Lid Support
will result in an entrapment hazard.
Lid
Body
Made in America
Quality Wooden Children’s Furniture and Accessories
Please check out to see our other products that are all made here in America. The safety of your children is our highest concern. We are a GREEN company and
hope you will be able to recycle the packaging mate-rial that we used to ship your product.
Use and care instructions:
The nish on this product is an environmentally friendly water base acrylic made by Sherwin Williams. It may be cleaned with a furniture polish, lemon oil or a non
abrasive cleaner using a soft cloth. DO NOT USE AMMONIA or products containing ammonia such as Windex glass or multi-surface cleaner. Scuff marks can
usually be removed by using a polishing compound sold at auto parts stores.
If you have a comment or a question please contact us. All of us hope you and your family will enjoy this product for many years.
If you have any problems, please call us and we will help you.
If you would like your Toy Storage Chest Personalized
with your child’s name. Contact us and we will take your
order and mail you your child’s name complete with
mounting instructions.