TC Electronic Gravy TRI CHORUS & VIBRATO User manual

USER MANUAL
TRI CHORUS & VIBRATO

2
Important Safety Instructions
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accor-
dance with the manufacturer’s instructions.
8 Do not install near heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampli-
fiers) that produce heat.
9 Only use attachments/accessories specified by the
manufacturer.
10 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
Warning!
• Toreducetheriskoffireorelectricalshock,donot
expose this equipment to dripping or splashing and
ensure that no objects filled with liquids, such as vases,
are placed on the equipment.
• Donotinstallinaconfinedspace.
Service
• Allservicemustbeperformedbyqualifiedpersonnel.
Caution:
You are cautioned that any change or modifications
not expressly approved in this manual could void your
authority to operate this equipment.
When replacing the battery follow the instructions on
battery handling in this manual carefully.
EMC/EMI
Thisequipmenthasbeentestedandfoundtocomplywith
the limits for a Class B Digital device, pursuant to part 15
of the FCC rules.

3
Theselimitsaredesignedtoprovidereasonableprotection
against harmful interference in residential installations.
Thisequipmentgenerates,usesandcanradiateradio
frequency energy and – if not installed and used in
accordance with the instructions – may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception – which can
be determined by turning the equipment off and on –, the
user is encouraged to try correcting the interference by
one or more of the following measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentand
the receiver.
• Connecttheequipmenttoanoutletonacircuit
different from the one to which the receiver is
connected.
• Consultthedealeroranexperiencedradio/TV
technician for help.
For the customers in Canada:
ThisClassBdigitalapparatuscomplieswithCanadian
ICES-003. Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.

4
www.tcelectronic.com - www.youtube.com/tcelectronic
(EN) Introduction
Congratulations! You have just bought a chorus pedal that is a stepping stone to a world of
inspiration, innovation and tone.
WeareproudtopresentGravyTriChorusandVibrato,providingTCElectronic’slegendarychorus
sounds,intuitivecontrols,andinstantsatisfaction.Throwinthelovelyfeeloftheoutstandingvibrato
withaflexibilitythatyouwillsimplynotfindinanyotherpedaloutthereandyouhaveGravyTriChorus
andVibrato.Welovetoneasmuchasanyguitaristoutthere,andwealwaysaimatpushingthe
boundaries.Wearethereforeveryexcitedtopresentabrandnew,groundbreakingconcept:TonePrint!
TonePrintgivesyouinstantaccesstocustom-tweakedsounds.Wehavegatheredanimpressivelistof
guitarheroesandhadthemtailortheirsignaturesounds–thetonesthatmadethemfamous.TonePrint
willnotjustbringyouclosetothesoundsofyouridols,theygiveyoutheiractualsounds!
UsingTonePrintsisbotheasyandfun.JustdownloadtheTonePrintyouwantfrom
www.tcelectronic.cometvoilà,yourfavoriteartisthasjustputaTonePrintinyourpedal.
Forgetemulation–let’stalkcollaboration!

5
1 - Effect on/off (true bypass)
2 - 1/4 inch mono jack input
3 - 1/4 inch mono jack input (for stereo in)
4 - 1/4 inch mono jack output
5 - 1/4 inch mono jack output (for stereo out)
6 - FX level control
7 - Speed time control
8 - Chorus/TonePrint/Vibrato selector
9 - Depth control
10 - Tone control
11 - Power in (9VDC)
12 - USB connection for exchanging TonePrint
settings and software updates.

6
Connecting
Input jacks - Use MONO for mono input and both MONO
andSTEREOifconnectingastereosource.
If you run the pedal on battery, we recommend removing
the mono input jack to preserve battery power when you
don’t play.
Output jacks – Connect to another pedal or directly into
an amp or mixer. Use MONO for mono setups and both
MONOandSTEREOforstereosetups.
Notice that it is possible to select between true bypass and
buffered bypass mode via a dip switch located under the
battery cover.
Power in–Usea9VDCpowersupplywiththefollowing
symbol:
USB
Connect to a computer using the supplied USB cable for
uploadofTonePrintpatches.
Theconnector-typeisMini-B.

7
The Controls
FX LEVEL
Controlstheintensityofthechorus.Thechorusingeffectoccurswhenapitchmodulatedsignal–think
vibrato–isplayedadjacenttoacleansignal.Thereforethemaxchorusintensityisachievedata50%
wet/dry mix. With Gravy, this is achieved by setting the FX level fully clock-wise.
SPEED
TheSPEEDknobsetsthechorusspeed–fromslowsmooth“Hi-Fi”tomuchmoresignificant“Leslie”
types at high speed.
DEPTH
DEPTHsetstherangeofthemodulation.ExperimentwithboththeSPEEDandDEPTHcontrolstoget
the effect you are looking for.
TONE
By adjusting the tone you can set how warm you chorus should sound. When using high settings on
bothspeedanddepthforthat“leslie-type”soundyoumightwanttoemphasizethelowerfrequencies
overthehigherones.TryturningTONEcounterclockwise.
CHORUS/TONEPRINT/VIBRATO SELECTOR
Theselectorswitchallowsyoutoselectbetweenthe3differenttypesofFX.

8
TRI CHO (Tri-Chorus)
TheTri-ChorusisavariationoftheregularChorusthatusesthreestereoChoruseswithvariousoffsets
for both depth, speed, phase, and chorus delay time to produce a unique, very broad and lush Chorus
sound.TheGravyhasbeenvoicedespeciallytonailthatold-schoolfatchorussound.
TonePrint
Consider the knobs and switches on your pedal as a few handles that actually control a large number
of parameters. Dedicated staff has defined the controls, - but wouldn’t it just be cool to let the world’s
leading guitar players contribute with their own definition of how the controls should work?
YES-thisisTonePrint.
OnceyouhaveselectedTonePrint,allcontrolsreactexactlyasdefinedbytheartistthathasprovided
theTonePrintandchangingtheTonePrintinyourpedaliseasy:
• ConnectthepedaltoyourMacorPCcomputerusingthesuppliedUSBcableandnavigateallthe
availableTonePrintsatwww.tcelectronic.com/TonePrint
or
• DownloadtheTonePrintAppfromGooglePlay or theAppStore and follow the on-screen
instructions.
VIBRATO
InthispositiontheGravypedalactsasaVibrato.Thesignalispitchmodulatedbutunlikeinachorus
theoriginalsignalisnotplayedadjacently.Takeyoursoundfromsubtlepitchmodulationtoanall-out
Leslie-typefeelbyvaryingtheSPEEDknob.

9
Bypass modes and Kill Dry on/off
Unscrew the back-plate and look for the two small dip-switches in the upper left corner.
Theupperdip-switch(closesttotheDC9Vinconnection),switchesbetweenTrueBypassmode
(default) and Buffered Bypass mode.
True Bypass – is a hardwire bypass that gives absolutely no coloration of tone when the pedal
isbypassed.UsingTrueBypassonallpedalsisaperfectchoiceinsetupswithafewpedalsand
relatively short cables before and after the pedals.
Buffered Bypass –If you use a long cable between your guitar and the first pedal, if you use many
pedals on your board and if you use a long cable from your board to the amp, then the best solution
True Bypass Buffered Bypass Kill-Dry - off Kill-Dry - on

10
Changing battery – Unscrew the thumb-screw on the back of the pedal and detach the back-plate.
Unmount the old battery and attach the new battery to the battery clip making sure the polarity is
correct.Thenremounttheback-plate.Tosavebatterylife,removetheinputjackwhenyoudon’tplay.
Batteries must never be heated, taken apart or thrown into fire or water. Only rechargeable
batteries can be recharged. Remove the battery when the pedal is not being used for a longer
period of time. Dispose batteries according to local laws and regulations.
will most likely be to activate the buffer in the first and last pedal in the signal chain. Can you hear the
differencebetweenapedalinTrueBypassorBufferedBypass?Maybe,maybenot,–manyfactors
apply; active/passive pick-ups, single coil/humbucker, cable quality, amp impedance and more. We
cannotgiveasingleultimateanswer.Useyourearsandfindthebestsolutionforyoursetup!
Kill-Dry on/off – With Buffered Bypass activated (upper switch to the right), the lower dip-switch sets
Kill-Dry on/off. Kill-Dry removes all direct signal from the pedals output and is the mode to use when
the pedal is placed in a parallel effects loop.
Kill-DryisNOTanoptioninTrueBypassmode.