TE Connectivity WMM8G-7-38 Original instructions

3G/4G/5G MIMO HIGH GAIN ANTENNA /// INSTALLATION GUIDE
3G/4G/5G MIMO HIGH
GAIN ANTENNA
INSTALLATION GUIDE AND SAFETY INFORMATION

3G/4G/5G MIMO HIGH GAIN ANTENNA
FORMASTWALANDDESKMOUNTING
3G/4G/5G MIMO HIGH GAIN ANTENNA /// INSTALLATION GUIDE
A. SELECTING A POSITION
PACKAGE CONTENTS
The device is shipped with the following items. If any of these items is missing or damaged, please contact your cus-
tomer service representative for assistance.
1x Antenna 1x U-Bolt 4x plain washers 1x desk stand
1x U-Bolt plate 4x Spring Washers 2x Wall Bracket plates 4x screws
2x Nuts
SELECT POSITION
For a good installation the antenna should be directed towards the stron-
gest network signal. In order to achieve this follow the guide below.
1. Connect the antenna to your router or modem with the antenna ad-
apter (if applicable) and coaxial cable provided.
2. Ensure that your device is connected to the network and displaying
the signal strength indicator.
3. With the antenna at selected location, rotate it in approximately 45
degree steps – in each position, you may need to wait for up to one
minute to allow the signal strength indicator to update.
Note: Signal strength indication may be displayed either:
• Graphically with bars, (where more bars is a better signal), or
MOUNTING THE ANTENNA
• Mounting the antenna internally: To mount the antenna internally use the supplied desk stand and follow the inst-
ructions at B. DESK MOUNTING INSTRUCTIONS
• Mounting the antenna externally: Mounting the antenna outside will provide optimum signal strength and data
rates. Begin by following the instructions at A.1 & A.2 concerning position and orientating the antenna. Then fol-
low C. MAST MOUNTING INSTRUCTIONS or D. WALL MOUNTING INSTRUCTIONS depending upon the equip-
ment you have available.

3G/4G/5G MIMO HIGH GAIN ANTENNA
FORMASTWALANDDESKMOUNTING
3G/4G/5G MIMO HIGH GAIN ANTENNA /// INSTALLATION GUIDE
IMPORTANT SAFETY INFORMATION
RF Safety Note – Ensure that the antenna is mounted in such a way that no person is likely to be within a
distance of 30cms (12”) from the antenna during use. Ensure that the antenna is used only as supplied the
co-axial cables should not be cut shorter or otherwise modified.
General Safety Note - Make sure that the product is mounted so that it cannot fall and cause injury. Do not
chew the product or put it in your mouth. Do not leave children unsupervised with the product or packaging.
Electrical Caution - Parts of this antenna are an electrical conductor. Contact with power lines can result in
death or serious injury. The antenna and supporting mast must not be close to any power lines during instal-
lation, use or removal. If the antenna is elevated and at risk from lightning strike it must be ensured that the
antenna is mounted and earthed appropriately by a trained professional in accordance with the relevant stan-
dards.
Waste electrical products should not be disposed of with household waste. All electronic products with the
WEEE logo must be collected and sent to approved operators for safe disposal or recycling. Please recycle
where facilities exist. Many electrical/electronic equipment retailers facilitate “Distributor Take-Back sche-
me”for household WEEE. Check with your Local Authority or electronic retailers for designated collection
facilities where WEEE can be disposed of for free.
RoHS 2 compliance is declared per Directive 2011/65/EU and its subsequent amendments with exemption
6.c applied. This product contains lead as an alloying element in a copper alloy containing up to 4% lead by
weight.
REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals, EC 1907/2006)
This product contains Lead (CAS No. 7439-92-1) which is classified as an SVHC (Substance of Very High Con-
cern) as being toxic to reproduction under Article 57c. of REACH. Do not chew parts or put them in mouth,
keep away from unsupervised children. Dispose of parts as WEEE waste do not send to landfill.
B. DESK MOUNTING INSTRUCTIONS (INTERNAL USE ONLY)
To Desk Mount this antenna you will need: 1x Antenna, 1x Desk Stand
Gently press the base of the antenna onto the desk stand ensuring that a ‘Click’ sound is made when the pegs are
engaged. Store any excess cable safely out of the way. Do not tightly wrap or bunch the cable.

3G/4G/5G MIMO HIGH GAIN ANTENNA
FORMASTWALANDDESKMOUNTING
3G/4G/5G MIMO HIGH GAIN ANTENNA /// INSTALLATION GUIDE
D. WALL MOUNTING INSTRUCTIONS
C. MAST MOUNTING INSTRUCTIONS
To Mast mount this antenna you will need: 1x Antenna, 1x U-Bolt, 1x U-Bolt Plate, 2x Washers, 2x spring washers, 2x
Nuts
MAST MOUNTING THE ANTENNA EXTERNALLY
Ensure that the selected mounting location can be safely accessed with the equipment that you have available and
mount the antenna so that it has at least 1 metre (3.3’) of clearance from all obstructions if possible. The antenna
should not be mounted directly on to metal masts or poles. If the antenna must be mounted to such a surface it must
be mounted at the lip of the roof or the very top of the pole such that the body of the antenna is elevated clear of
the metal surface.
ENSURE A SAFE CONNECTION
Secure the antenna in place and waterproof the exposed connections. Fully tighten the mounting hardware. If expo-
sed the RF connector joint should be waterproofed with a weatherproof electrical tape (self amalgamating type is
recommended) allowing a significant overlap of each turn and ensuring that the overlap is in the opposite direction
to predicted water fall.
To Mast mount this antenna you will need: 1x Antenna, 2x Wall Bracket Plates, 4x Screws, 4x Washers, 4x spring was-
hers, 2x Nuts

3G/4G/5G MIMO HIGH GAIN ANTENNA
FORMASTWALANDDESKMOUNTING
3G/4G/5G MIMO HIGH GAIN ANTENNA /// INSTALLATION GUIDE
WALL MOUNTING THE ANTENNA
1. Fix the mounting bracket to the external wall or other flat surface using suitable screws and wall plugs (not sup-
plied).
2. Fix the mounting bracket to the antenna using the the washers and screws supplied.
3. Fix the antenna to the wall mounting bracket
4. Secure the antenna in place and waterproof the exposed connections.Fully tighten the mounting hardware. If
exposed the RF connector joint should be waterproofed with a weatherproof electrical tape (self amalgamating
type is recommended) allowing a significant overlap of each turn and ensuring that the overlap is in the opposite
direction to predicted water fall.