Teac DVP1013 User manual

USER MANUAL
WARRANTY INFORMATION INSIDE. PLEASE READ
www.teac.com.au
IMPORTANT !
DVP1013
PORTABLE LCD DVD PLAYER
Trademark of TEAC Corporation JAPAN

WARRANTY PROCEDURE v1.6: May 2015
Please read the owner’s manual carefully and ensure that you have followed the correct installation and operating procedures.
1. Please read this warranty card.
2. Keep your purchase receipt to enable you to proceed quickly in the event of a Warranty Service.
3. If you require Warranty Service, please contact the TEAC Warranty Service Hotline at 1300 553 315 for assistance. Please ensure
that you have the model number, serial number and purchase receipt ready when you call.
Please complete the section below and keep this information for your own records.
Owner’s Name
Owner’s Address
Postcode
Model Name/No. Serial No.
Dealer’s Name
Dealer’s Address
Postcode
Thank you for selecting a TEAC product.
If your TEAC product malfunctions, please call us directly for warranty support
between Monday to Friday at 8.30AM –5PM AEST at the
TEAC Warranty Service Hotline
1300 553 315
For other enquiries, please contact us at:
www.teac.com.au
When calling to receive warranty service, please have:
1. Your model and serial number
2. Proof of purchase
3. And your product in front of you
NOTE:
- You are required to provide a copy of your proof of purchase in order to have your claim
processed.
- Please read the Terms and Conditions for details of your warranty entitlement.

TERMS AND CONDITIONS v1.6: May 2015
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
1. TEAC warrants that this product is free from defects in material and workmanship under normal domestic use with reasonable care and skill.
Maintenance and cleaning (i.e. laser head) is not covered by this warranty. The TEAC warranty only applies to TEAC products purchased
NEW from a TEAC Authorised Retailer in Australia. This warranty only applies to the original purchaser and cannot be transferred.
2. The benefits to the consumer given by this Warranty are in addition to other rights and remedies of the consumer under a law in relation to
goods or services to which the warranty relates, being the Australian Consumer Law.
3. Refund or replacement via your TEAC Authorised Retailer is available for a period of 14 days after purchase for goods that have been
inspected and determined to have a major failure. Refund and exchange is not applicable for change of mind.
4. Subject to the terms herein, this warranty effectively covers TEAC products, excluding products purchased for commercial purposes, as
specified in the Warranty Periods Table below from the date of purchase. Commercial use products are covered for 12 months only
(Authorised Service Centre).
TEAC PRODUCT
excluding commercial use products
SIZE (TV)
WARRANTY PERIOD
from date of purchase
WARRANTY SERVICE TYPE
LED/LCD TV
42” and above
12 months
In-home service*
19” to 40”
12 months
Authorised Service Centre Service
All other TEAC products
N/A
12 months
Authorised Service Centre Service
5. In Home Service/Pick up* Service
This service will only be provided as part of this warranty if all the following conditions are met;
a) The product is indicated in the Warranty Period Table.
b) The product is within the warranty period.
c) The product is located within the normal service area of the local TEAC Authorised Service Centre.
If TEAC determines that the product is not repairable on site, TEAC can complete the repair by taking the product to a TEAC Authorised
Service Centre.
Authorised Service Centre Service
The purchaser is required to send the product at their own expense to the nearest TEAC Authorised Service Centre for repair. In this event,
proof of purchase is required to support a warranty claim. After the repair, the product will be available for collection by or return to the
purchaser at a fee upon request. TEAC in-home service can be made available at a fee upon request.
6. A 12-month replacement warranty is applicable to all Accessories such as Remotes, Power Adapters and Cables.
7. TEAC will ensure to the best of its abilities that all required parts are made available for any required service/repair.
8. TEAC Australia Pty Ltd and its Authorised Service Centres will use their best endeavours to complete product repairs within a reasonable
period based on available resources and workload during the time when service is requested and performed.
9. Refurbished parts may be used to repair the product. In the case of a replacement, the product may be replaced, with a refurbished unit of the
same type or, if one is unavailable, a similar refurbished model with equal or better features and specifications.
10. Please be advised that if the product presented for repair is capable of retaining user-generated data, the data may be lost during servicing.
Customers are strongly encouraged to back up all important information/data before sending the product in for service/repair.
11. Service will be provided only during normal business hours and under safety conditions and circumstances. TEAC and its authorised service
agents can refuse any repair if safety, in relation to OH&S, becomes a concern to its staff or authorised service agents’ personnel.
12. The warranty is void and warranty claims may be refused, subject to the Australian Consumer Law, if:
a) The product was not transported, installed, operated or maintained according to manufacturer instruction, or
b) The product was abused, damaged, tampered, altered or repaired by any unauthorised persons, or
c) Product failure is due to accidents during use, installation or transit, power surges, use of defective or incompatible external devices, exposure
to abnormal conditions such as excessive temperatures or humidity, or entry of liquids, objects or creatures into the product, cockroach
infestations, or
d) The customer is unable to provide proof of purchase of the product for verification, or
e) The serial number of the product is missing or has been tampered with.
13. Where any repairs or services required that are outside of the terms and conditions of this Warranty are requested by the customer, or where
a fault is determined to be outside of the terms and conditions of the Warranty during an In-Home Service call, the customer shall be charged
for the cost of the repair and/or the In-Home service call fee.
14. No one is authorised to assume any liability on behalf of TEAC or impose any obligation on it, in connection with the sale of any equipment
other than as stated in this warranty and outlined above.
15. TEAC and/or its Authorised Service Centres reserve the right to inspect and verify whether the product is exhibiting a major failure as claimed
bycustomers/retailers.
16. LCD dead pixel policy, please contact TEAC at [e-mail] for assistance.

TABLE OF CONTENTS
1
Safety Information
Safety Precautions
Some Do‟s and Don‟ts On The Safe Use Of Equipment
USB Usage Precautions
2
Introduction
Features
Accessory List
Supported Disc Formats
Disc Care
6
Panel and Remote Operation
Panel Controls
Side Panel Overview
Remote Control
Battery Installation
8
Basic Operation
Using the AC Adaptor
Using the DC Car Charger
Using the Rechargeable Battery
External System Connection
DVD/CD Playback
Using USB Drives and SD/MMC/MS Cards
USB/CARD Multimedia Playback
CD Ripping
DVD Mode Setup
12
Reference
Troubleshooting
Specifications
20

SAFETY INFORMATION
2
Safety Precautions
To enjoy the best performance and become familiar with the product features, please read this
manual carefully before operation.
Please read through the manual carefully before using and retain for future use.
ATTENTION: TO AVOID RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT OPEN THE COVER OF THE UNIT. ANY
MALFUNCTIONS SHOULD BE SERVICED ONLY BY
AUTHORISED PERSONNEL.
WARNING: THERE IS UNINSULATED DANGEROUS
VOLTAGE WITHIN THE PRODUCT ENCLOSURE THAT
MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE
A RISK OF ELECTRIC SHOCK.
NOTE: IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE LITERATURE ACCOMPANYING
THE APPLIANCE.
THIS MARKING CAN BE FOUND ON THE REAR PANEL
OF THE UNIT. THIS PRODUCT IS CLASSIFIED AS A
CLASS 1 LASER PRODUCT AND DOES NOT EMIT
HAZARDOUS RADIATION OUTSIDE THE UNIT.
Power Lead Protection
1. Please use normal power sources. This unit can be operated on an AC adaptor (included), a
rechargeable battery (included), or a car power adaptor (optional).
2. Make sure that the input voltage of the AC adaptor is in line with the local voltage. Otherwise,
the AC adaptor and unit may be damaged.
3. Do not touch the AC adaptor with wet hands so as to avoid electric shocks.
4. When connecting with the car power (cigarette lighter) adaptor, ensure that the inpur voltage
of the adaptor is identical with the car voltage.
5. Hold the plug to disconnect the AC adaptor. Do not pull on the power cord. The power plug
should be easily accessible at all times.
Important Safety Instructions
1. Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for cleaning.
2. Placement – Avoid placing the unit where there is a lot of movement or vibration, such as on
a car dashboard or an unstable shelf.
3. Water and moisture – Do not use this product near water, for example near a bath tub, wash
bowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool or the like. If any
liquid enters the unit, disconnect the power plug immediately and contact the nearest
authorised service centre for examination and repair.
SAFETY INFORMATION INTRODUCTION PANEL & REMOTE UNIT OPERATION REFERENCE

SAFETY INFORMATION
3
4. Ventilation – The product should be used in a well-ventilated area to avoid overheating. The
product should not be placed on the bed or sofa.
5. Servicing – Do not attempt to service this product yourself as opening or removing the cover
may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
6. Disc – Do not use a cracked disc as they will break easily and cause personal injury or
product damage.
7. Heat sources – The product should be kept away from heat sources such as radiators, heat
registers, stoves or other heat-producing products.
8. Magnet sources – Do not place the product next to a magnetic field such as speakers.
9. Headphones – To avoid damage to your hearing caused by loud volume, set the volume level
to its lowest before playback, and then adjust the volume as desired.
10. Condensation – When the unit experiences a rapid temperature change when suddenly
moved from a cold place to a warm one, moisture will condense on the pickup lens and result
in malfunction or playback difficulties. When this happens, remove the disc, connect the
power plug and leave it on for 2-3 hours.
11. Others –
a. Do not watch films while driving to avoid traffic accidents.
b. Pull on the plug when disconnecting the power adaptor. Do not pull the cable.
c. Do not touch the product with wet fingers as it may cause electric shock.
d. Do not gaze at the laser rays in order to avoid eye discomfort and injury.
e. Turn the power off if the unit is not used for a long time instead of leaving it in
Standby Mode.
f. To retain the life of the rechargeable battery, make sure that the unit is turned on
once in a while and charged every 3 months if it is not used for a long time.
CAUTION
Do not expose the unit to direct sunlight, leave the DVD player inside a closed car on
a sunny day, or on other sources of heat such as a TV! This may cause the unit
surface to warp, change colour or become damaged.
After a long period of using the unit, the surface may become hot. This is not a
malfunction, but takes caution against burns.
Charge the rechargeable battery in this unit only with the provided power adaptor.
Stop charging once the battery is fully charged to retain battery strength.

SAFETY INFORMATION
4
Some Do’s and Don’ts on the Safe Use of Equipment
This equipment has been designed and manufactured to meet international safety standards.
However, care must be taken to ensure personal safety and optimum product performance.
DO read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and inter-
connections between the pieces of equipment) are properly made and in accordance with the
manufacturer’s instructions. Switch off and unplug the power before making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your
equipment.
DON’T remove any fixed cover as this may expose dangerous voltages.
Overheating will cause damage and shorten the life of the equipment.
DON’T allow electrical equipment to be exposed to dripping or splashing, or objects filled with liquids,
such as vases, to be placed on/near the equipment.
DON’T place hot objects or naked flame sources such as lighted candles or nightlights on, or close to
equipment. High temperatures can melt plastic and lead to fires.
DON’T use equipment such as personal stereos or radios so that you are distracted from the
requirements of traffic safety.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is
designed for unattended operation. Switch off using the switch on the equipment and make sure that
your family knows how to do this. Special arrangements may need to be made for infirm or
handicapped people.
DON’T continue to operate the equipment if you are in any doubt about if it’s working normally or if it’s
damaged in any way. Switch it off, unplug the mains power and consult your dealer.
ESD Remark: In case of malfunction due to electrostatic discharge just reset the product
(reconnection of mains power may be required) to resume normal operation.
SAFETY INFORMATION INTRODUCTION PANEL & REMOTE UNIT OPERATION REFERENCE

CD/DVD Drives, and other devices connected via USB cannot be
USB Storage Device (Flash Memory) up to maximum 16GB can be used.
SAFETY INFORMATION
5
USB Usage Precautions
Never turn the unit off or disconnect a USB Storage Device (Flash Drive) when it is being
accessed. Doing so could damage the unit and the connected USB storage device.
Do not use a device that has a maximum current consumption of 100 mA or more.
Do not use a device that has security functions or other special functions.
Do not use a device that is divided into two or more partitions.
A USB hub cannot be used to connect USB devices to this unit.
USB storage devices that can be played on this unit

Some flash memory players that charge from USB terminals cannot be used for
playback.

used.
This unit cannot copy or move files.
Playable formats: FAT12, FAT16, FAT32
Depending on the condition of the USB flash drive, this unit might not be able to play
the files on it or skipping might occur.
NTFS, HFS and HFS+ formats are not supported and cannot be used.
Max. number of playable folders: 200
Max. number of playable files: 999
If the USB storage device contains more than 999 files or 200 folders, this unit
cannot play it back correctly.
This unit cannot play files that are larger than 2GB.
Files with variable bit rates might not play correctly.
File information display
The display of this unit can only show single-byte letters and numbers.
If the file information contains Japanese, Chinese or other double-byte characters,
playback is possible but the name will not be shown correctly.
SAFETY INFORMATIONINTRODUCTIONPANEL & REMOTEUNIT OPERATIONREFERENCE

Supporting AVI video
DVP1013
INTRODUCTION
6
Thank you for choosing TEAC. Please retain this user manual for future reference. If any
assistance is needed, please contact our Customer Support Hotline at 1300 553 315.
Features
1. High resolution colour TFT LCD full screen display
2. Super electronic shock resistance (3 seconds for DVD, 10 secondsfor CD/VCD
and 90 secondsfor MP3)
3. Compatible with most DVD, SVCD, VCD, CD, MP3, AVI discs
4. Built-in super power polymer lithium battery for up to 2-3 hours of continuous play
5.
6.USB 2.0 port for playback and CD ripping
7.
8.Full function remote control
9. Regulated power supply adaptor for AC100V-240V
10.Personalised adjustable TFT display
11.Video output to connect to TV at home
12.Sleek design thatfits right into your modern lifestyle
Accessory List
Composite AV Cable Remote Control User Manual Power Adaptor
Earphones
Remote Control
Battery x2 Car Adaptor
DVD/
SD/USB DISPLAY
MUTE
1 2 3
TITLE
5 6 7
9 0 10+
REPEATRETURN
AUDIO
A-B
SETUP PB
C
MENU VOL+
ENTER VOL-
MODE GOTO ZOOM
4
8
ANGLE
PROGRAM
STANDBY
SUBTITLE
CDRIPPIN G
USER MANUAL
WARRANTY INFORMATION INSIDE. PLEASE READ
www.teac.com.au
IMPORTANT !
DVP1013
PORTABLE DVD PLAYER
Trademark of TEAC Corporation JAPAN
Carry Bag
SAFETY INFORMATION INTRODUCTION PANEL & REMOTE UNIT OPERATION REFERENCE
decoding
SD/MMC card slot for playback

INTRODUCTION
7
Supported Disc Formats
Disc Type Content Size
Video DVD Audio + Video 12cm/8cm
DVDR/RW Audio + Video 12cm/8cm
Video CD/ Super VCD Audio + Video 12cm/8cm
Audio CD Audio 12cm/8cm
JPEG Video (Photo) 12cm/8cm
Picture CD Video (Photo) 12cm/8cm
CDR/RW Audio + Video 12cm/8cm
 NOTE:
Disc types not mentioned above cannot be used.
Playback on some discs such as CD-R, CD-RW, DVDR and DVDRW may require
special instructions from the disc manufacturer. Please refer to operation sheets
enclosed with these discs.
Disc Care
1. Please hold all discs by the edge or the centre hole.
2. Do not touch and do not stick paper or tape on the reflective side of the disc.
3. Do not used damaged, cracked or warped discs to avoid damaging the unit.
4. Fingerprints or stains on discs may weaken the reflected light from discs and affect
the signal quality and in turn, playback performance. Use a clean, soft cloth to clean
discs using an outward motion straight from the centre. If the disc is too dirty, clean it
with a moist soft cloth first, and then a dry soft cloth. Do not use cleaning sprays,
benzene, thinner, antistatic agent or any other solvents as this may damage the
surface of the discs.
5. Please keep discs in their original cases to avoid bending them. Do not store discs
under high temperature, high humidity or in direct sunlight as this will damage the
discs. Please read the instructions on discs labels and packaging carefully.
SAFETY INFORMATIONINTRODUCTIONPANEL & REMOTEUNIT OPERATIONREFERENCE

Press to turns unit on or back to Standby
STANDBY
PANEL AND REMOTE OPERATION
8
Panel Controls
Button Function
1.
2.
MENU In DVD/USB/CARD Mode, press to show the menu for the
TFT display
In AV In Mode, press to enter menu setup
3. DVD/USB/SD Press to cycle through the following modes: DVD>USB>SD
4.
5.
SETUP Press to show the DVD setup menu
6.
7.
8.
SAFETY INFORMATION INTRODUCTION PANEL & REMOTE UNIT OPERATION REFERENCE
STANDBY
TFT On/Off Press to turn the LCD screen on or off
MODE Press to switch between AV IN Mode
SETUP Press to show the DVD setup menu
 Press to stop playback
Play/pause playback

Insert a SD/MMC memory card
SD/MMC
PANEL AND REMOTE OPERATION
9
9.
10. / LEFT navigation button
During play back, fast rewind (scan backwards) on the current
track
11. / UP navigation button
During playback, go to a previous track/chapter
In Menu Setup, return to the previous page
12. / RIGHT navigation button
Fast forward (scan forwards) on the current track
13. OK Confirm the selected item
14. / DOWN navigation button
During playback, go to the next track/chapter
In Menu Setup, go to the next page
15.
16.
Side Panel Overview
Button Function
1. USB Port Connect to a USB device
2. Socket
3. Earphone Jack Connect earphones/headphones for private listening. The
unit‟s speakers are muted while this jack is in use.
4. AV OUT Jack AV output terminal to connect external media devices
5. AV IN Jack AV input terminal to connect external media devices
6. POWER Turn on/off power to the unit completely.
7. DC Jack Connect the DC 12V power adaptor to power and charge the
unit
SAFETY INFORMATIONINTRODUCTIONPANEL & REMOTEUNIT OPERATIONREFERENCE
VOL- Decrease volume level
AUDIO Press to switch the audio track
VOL+ Increase volume level
SD/MMC

PANEL AND REMOTE OPERATION
10
Remote Control
STANDBY: Turns unit on or back to Standby
DVD/SD/USB: Press to cycle through DVD>SD>USB Modes
DISPLAY: Display/hide detailed information about the current played media
MUTE: Turn sound on/off
1-10+: Number buttons for numerical input. For numbers 10 and above, use the 10+
button
MODE: Switch between TV Mode and DVD Mode
ANGLE/PROGRAM: While playback is stopped, press to enter the PROGRAM function.
During DVD playback, press to select from available camera angles. (Depends on
availability on disc)
GOTO: Press to input a specific title/chapter on the DVD to jump to.
ZOOM: Press repeatedly to cycle through different Zoom views.
Please see
next page for
details
DVD/
SD/USB DISPLAY
MUTE
123
TITLE
567
9 0 10+
REPEATRETUR
N
AUDIO
A-B
SETUP PB
C
MENU VOL+
ENTER VOL-
MODE GOTO ZOOM
4
8
ANGLE
PROGAM
DVP1013
STANDBY
SUBTITLE
CD RIPPIN G
SAFETY INFORMATION INTRODUCTION PANEL & REMOTE UNIT OPERATION REFERENCE

PANEL AND REMOTE OPERATION
11
Battery Installation
1. Open the battery compartment by taking out the battery cover.
2. Insert 2 AAA batteries, making sure to match +/- polarities correctly.
3. Close the battery compartment securely.
CAUTION
To prevent damage to the remote control, make sure to install batteries
correctly. Do not mix old and new batteries.
Dispose of batteries safely and appropriately. Contact your local authorities
or dealer for advice on battery disposal.
Keep batteries out of reach of children.
Remove battery if the remote control is not used for a long time.
TITLE: Press to return to disc title menu in DVD mode
RETURN: Return to previous menu.
CD RIPPING/SUBTITLE: In DVD Mode, press to select from available subtitles. During
audio CD playback, press to enter CD Ripping Mode.
REPEAT: Press repeatedly to cycle through available repeat modes
A-B: Use to loop a specific section of the track. Press once during playback to mark Point
A. Press again to mark Point B. Points A-B will start playing in repeat.
SETUP: In DVD mode, press to show DVD Setup Menu.
PBC MENU: Show previous disc menu. With PBC enabled VCDs, press to turn PBC
on/off.
: Menu navigation buttons
ENTER: Press to confirm a menu selection
VOL+/-: Increase/decrease audio level
AUDIO: Select from available audio tracks
: Play/pause playback
: Stop playback
: Fast forward current track
: Fast rewind current track
: Skip back during playback
: Skip forward during playback
*NOTE: These functions (title, subtitle etc) depend on availability of the corresponding
features on the disc. For more information contact the disc manufacturer.
SAFETY INFORMATIONINTRODUCTIONPANEL & REMOTEUNIT OPERATIONREFERENCE

When the battery is fully charged, the LED indicator will light is not bright.
BASIC OPERATION
12
Using the AC Adaptor
Connect the unit to a wall power outlet using the provided AC adaptor. CAUTION: Turn off
the unit before unplugging the AC adaptor to avoid damaging the unit. Make sure the power
supply is turned off before making or changing any cable connections.
1. Insert the AC adaptor into the DC IN jack on the unit.
2. Insert one end of the power supply cable into the input jack of the adaptor and plug
the other end into the wall power outlet.
3. Switch the power on at the wall outlet to start using AC power.
Using the DC Car Adaptor
Connect the unit to power in the car using the DC car adaptor and the car‟s cigarette lighter
receptacle. CAUTION: Make sure the unit is turned off before making or changing any cable
connections.
1. Insert the DC car adaptor into the DC IN jack on the unit.
2. Plug the other end of the adaptor into the car‟s cigarette lighter receptacle.
3. Switch the power on at the wall outlet to start using the power supply from the car.
Using the Rechargeable Battery
Battery specifications:
Output: 7.4V
Capacity: 1800mA/H
Standard charge time: >3 hours
Standard discharge time: >2 hours
Storage temperature: -20°C~45°C
Standard charging temperature: 0°C~45°C
Standard discharging temperature: -20°C~45°C
The battery can be charged via the AC power adaptor or car adaptor. In order to charge the
battery, the unit must be powered off. The rechargeable battery will reach its maximum
performance after a few full charge/use cycles. When the battery is low, the screen may start
to flash. Charge the unit if this happens.
1. Connect the power adaptor to the unit and wall power outlet as described in the
previous section.
2. When charging the battery, the LED indicator will light up in red.
3.
 NOTE:
CAUTION: Keep the battery away from sunshine or high temperatures and do not
use it in the car, as this will shorten battery life and capacity and may even cause fire.
Even if the DVD player has not been used for a long time, you should recharge the
battery once every 3 months to retain full use of the battery.
SAFETY INFORMATION INTRODUCTION PANEL & REMOTE UNIT OPERATION REFERENCE

motion to increase the speed. The max speed is x20. Press PLAY to resume playing.
Using SD/MMC Memory Cards
Insert the SD/MMC Memory card into the CARD slot.
Using USB Drives and SD/MMC Cards
BASIC OPERATION
13
External System Connection
Connect to external output devices like TVs, amplifiers or headphones. Ensure that the
settings
Connecting to TV and Stereo Amplifier
Mini-plug: Connect to the AUDIO/VIDEO OUT jack of the portable DVD player.
Yellow plug: Connect to the VIDEO IN jack of the TV.
Red plug: Connect to the AUDIO IN R jack of the stereo amplifier.
White plug: Connect to the Audio In L jack of the stereo amplifier.
DVD/CD Playback
1. Connect the unit to power and turn it on using the side POWER switch.
2. Open the DVD compartment by pressing the OPEN button.
3. Place the CD or DVD with the printed label facing upwards, then close the tray.
4. Use the playback control buttons to start playback.
5. Adjust the volume to the desired level using the VOL+/- buttons.
Note: If the unit is connected to an external screen such as TV, ensure that the TV is
switched to the correct input mode such as AV Mode.
During DVD/CD playback, the following actions are available.
Pause: Press the button to pause playback. Press again to resume playing.
Stop: Press the  button to stop playback.
Forward/Rewind: Press and hold the / buttons to fast forward/rewind. Repeat this
Previous/Next track: Tap the / buttons for previous/next track.
GOTO: Press the GOTO button and enter a title and chapter number to jump to.
Other functions are available depending on the disc format and content.
This unit supports playback of JPEG, MP3, WMA, XVID and AVI files.
Using USB drives
1. Connect the unit to the power supply and switch the unit on.
2. Insert the USB memory stick into the USB 2.0 port.
3. If there is no disc loaded in the unit, it will auto-detect the USB stick and start to read
and playback compatible media files. Otherwise, press the DVD/USB/SD button to
switch to USB input.
1. Connect the unit to the power supply and switch the unit on.
2.
SAFETY INFORMATIONINTRODUCTIONPANEL & REMOTEUNIT OPERATIONREFERENCE

motion to increase the speed. The max speed is x20. Press PLAY to resume playing.
compatible USB device or SD/MMC Card storing compatible media files must be
BASIC OPERATION
14
3. If there is no disc loaded in the unit, it will auto-detect the memory card and start to
read and playback compatible media files. Otherwise, press the DVD/USB/SD button
to switch to CARD input.
 NOTE: If another USB stick/memory card is already inserted, the unit will not auto-detect
the second USB/CARD memory device. Press the DVD/USB/SD button to switch to the
desired source.
USB/CARD Multimedia Playback
Access this feature by entering USB or CARD Mode. To play multimedia files, a
connected.
 NOTE:
This unit only supports USB devices with a FAT32 file system. It will not support
NTFS file systems.
This unit supports XVID, AVI, MP3, WMA and JPEG file playback. However, due to
other variations in file formats, some files may not play even though they are the
supported file types.
Music Playback
1. The music will normally start playing in sequence automatically. Use  to navigate
the file list if you wish to play a specific music file.
2. Press OK to start playing a selected music track
3. When the player reaches the end of the file sequence, it will stop playing and display
the welcome logo. Press the button to return to the Multimedia Menu.
During music playback, the following actions are available.
Pause: Press the button to pause playback. Press again to resume playing.
Stop: Press the  button to stop playback.
Forward/Rewind: Press and hold the / buttons to fast forward/rewind. Repeat this
Previous/Next track: Tap the / buttons for previous/next track.
GOTO: Press the GOTO button and enter a specific time to jump to in the current track in
HH:MM:SS format.
Tip: To play specific tracks or a music playlist during the picture slide show start the music
playback first. Then, press RETURN to go to the Multimedia Menu, and navigate to the
image files per the instructions below. The music will continue playing after the picture slide
show starts.
Picture slide show
1. In the file list, use  to choose a picture to start the slide show with.
2. Press OK to start the slide show.
During the slide show, the following actions are available.
Pause: Press the button to pause playback. Press again to resume playing.
SAFETY INFORMATION INTRODUCTION PANEL & REMOTE UNIT OPERATION REFERENCE

In order to rip, an audio CD must be loaded and a USB drive or SD/MMC
This unit can record to a connected USB drive or SD/MMC memory card
BASIC OPERATION
15
Stop: Press the  button to stop playback.
Previous/Next track: Tap the / buttons for previous/next file.
 direction buttons: Rotate the current picture. Note: Some picture CDs may have
design limitations that make this feature unavailable.
ZOOM: Press the ZOOM button on the remote control. 100% will display on the screen.
Press / to zoom in or out. Press ZOOM again to exit Zoom view.
Movie Playback
1. In the file list, use  to choose a movie to watch.
2. Press OK to start the movie playback.
During movie playback, the following actions are available.
Pause: Press the PAUSE button to pause playback. Press again or press PLAY to
resume playing.
Stop: Press the STOP button to stop playback. Exiting to the main USB menu or the TV
mode will also stop playback.
Forward/Rewind: Press and hold the / buttons to fast forward/rewind. Repeat this
motion to change fast forward/rewind speeds.
Previous/Next track: Tap the / buttons for previous/next track.
GOTO: Press the GOTO button and enter a specific time to jump to in the current track in
HH:MM:SS format.
Subtitle: Press SUBTITLE to choose subtitles (subject to availability from the movie file)
Programmable Playback
Programme a playlist with a customised track sequence.
1. Press the PROG button to access the playlist setup menu.
2. Key in the desired track numbers into the list in sequence.
3. Use the  buttons to select the PLAY option at the bottom of the screen. Press
OK to start playback. Press PROG to exit the playlist setup menu.
CD Ripping
. Use this
function to save music tracks from Audio CDs into MP3 files.
 NOTE:

memory card must be connected to the unit.
Ensure that the connected media has enough free memory and is not write-protected.
DO NOT use Hard Disk Drives as they are generally not suitable for recordings with
this unit. We suggest using USB devices up to 32GB and formatted in the FAT32 file
system.
Only use USB2.0 high-speed USB media.
CAUTION: Please note that some Audio CDs are copyright protected and are not
to be copied.
SAFETY INFORMATIONINTRODUCTIONPANEL & REMOTEUNIT OPERATIONREFERENCE

STRAGE: Select USB or CARD to rip to.
menu, select QUIT.
Select 'STAR
BASIC OPERATION
16
Ripping Music CDs
1. Start in DVD Mode.
2. Load an Audio CD.
3. Connect a compatible USB flash drive.
4. Press the CD RIPPING button to access
the conversion function.
5. Adjust the available options to your
preference (described below).
a. SPEED: ripping speed 1x or 4x
b. BITRATE: higher bitrate for higher
quality, lower bitrate for smaller files.
c. ID3 TAG: Create tag On/Off
d.
6. In the TRACKS column, select desired
tracks from the list of available tracks
and confirm with the OK button.
7. T‟ to start ripping.
8. When ripping is complete, the unit
returns to the ripping menu. To exit the
SAFETY INFORMATION INTRODUCTION PANEL & REMOTE UNIT OPERATION REFERENCE
RIP CD - UN K N OW N AL BU M
TRACKS
START
QUIT
ENCODE R OPTION S
SPEED 1x
BITRATE 128KBPS
FILE OPTIONS
CRATE ID3 TAG
CRATE PLAYLIST
STRAGE OPTIONS
STRAGE USB
RIP CD - UN K N OW N AL BU M
TRACKS
START
QUIT
SUMMARY
TOTAL TRACKS 20
TOTAL TIME 77:40
TOTAL SIZE 71 . 1 M B
PRESS ENTER TO BEGIN
RIP CD - UN K N OW N AL BU M
TRACKS
START
QUIT
PRESS ENTER QUIT
RIP CD - UN K N OW N AL BU M
TRACKS
START
QUIT
1.
2.
3.
4.4.
5.
6.
7.

playback resuming.
OSD Language
LANGUAGE Setup
Password
Rating
Set screen aspect ratios (4:3PS 4:3LB 16:9)
TV Type
power resume
BASIC OPERATION
17
DVD Mode Setup
Press the SETUP button to show this menu. Adjust system and playback settings for this
unit using the Setup Menu. The Setup Menu is divided into tabs showing submenus with
options for different features.
General Setup
Option
Description/Settings
SAFETY INFORMATIONPANEL & REMOTEUNIT OPERATIONREFERENCE
SYSTEM SETUP
power resume
TV Type
Password
Rating
Default
Enable/disable memorising of last viewed track position for quick
Password protect according to rating
Customise password. The default password is “0000”. To change the
password, input the old password once and then the new password
twice.
Default Reset all settings back to factory default.
SYSTEM SETUP
power resume
TV Type
Password
Rating
Default
LANGUAGE SETUP
Osd Language
Audio Lang
Subtitle Lang
Menu Lang
Option Description/Settings
Audio Language Set a preferred track language to activate if the disc has the
corresponding track language available
Subtitle
Language Set a preferred subtitle language to activate if the disc has the
corresponding subtitle language available
Menu Language Set a preferred menu language to activate if the disc has the
corresponding subtitle language available
Set the language used in the OSD menu