TECHLIGHTING Zur Pathway 700OAZUR Series User manual

Installation Instructions for
Zur Pathway
920OAZUR
OUTDOOR
1A
Loosen the four set screws on fixture(Do Not Remove)
base with the provided Allen wrench and remove the
base plate.
1
Prepare the Fixture
ALLEN
WRENCH
1
1
1 1
BASE PLATE
SET SCREW
1
700OAZUR_ 1.1
2A
Attach the stake to the base plate by tightly screwing
down the provided stake bolt through the center hole
of the base plate and the stake.
Reattach the base plate assembly to fixture and tighten
down the set screws (reversal of Section 1A).
1
STAKE
STAKE BOLT
BASE PLATE
2
Install the Fixture
For Stake Install - see section 2
For Concrete and
other Hard Surfaces - see section 3
INSTALLATION OPTIONS:
CAUTION RISK OF FIRE-
This product must be installed in accordance with
the applicable installation code by a person familiar
with the construction and operation of the product
and the hazards involved.
Use minimum 90°c supply conductors.
GP I :ENERAL RODUCT NFORMATION
This product is suitable for wet locations.
12VAC input only.
If using Tech Lighting magnetic transformers, this product be
dimmed with a low-votage magnetic dimmer. For all other
transformers, consult with the manufacturer for compatible
dimmers.
WARNING – Risk of Electric Shock. Install all luminaires
10 feet (3.05 m) or more from a pool, spa, or fountain.
Unit low voltage cable is to:
a) be protected by routing in close proximity to the
luminaire or fitting, or next to a building structure such
as a house or deck;
b) not be buried except for a maximum 6 inches (15.2
cm) in order to connect to the main low voltage cable;
and
c) have the length cut off so that it is connected to a
connector within 6 inches (15.2 cm) from a building
structure, a luminaire, or fitting.

2
2B
3
4
Bring the power wires to the fixture location in
accordance with local electrical codes.
Connect the white fixture wire to one of the low-
voltage power line wire with the provided outdoor
waterproof wire nut.
Connect the black fixture wire to the remaining low-
voltage power line wire with the provided outdoor
waterproof wire nut.
5
2C
3
5
6
Install the Fixture to Concrete
(or other hard surfaces)
1
2
Bring the power wires to the fixture location in
accordance with local electrical codes.
Mount the base plate to an even and smooth surface
using the appropriate template, which can be found on
the following pages. Ensure that length of the lag bolts
or anchor bolts do not exceed 0.58” from the mounting
surface in order to leave enough clearance for the
fixture to fit properly over the base plate.
3A
0.58”
1
2
FIXTURE
BASE PLATE
BASE PLATE
3B
4
5
3
4
Bring the power wires to the fixture location in
accordance with local electrical codes.
Connect the white fixture wire to one of the low-
voltage power line wire with the provided outdoor
waterproof wire nut.
Connect the black fixture wire to the remaining low-
voltage power line wire with the provided outdoor
waterproof wire nut.
5
6Stake the fixture to the desired location and properly
bury the wire and wire nut connections.
BASE PLATE

3
4A
Remove the two socket head screws and O-rings using
the proved Allen wrench to access the locking set screw.
Make sure to only loosen the two set screws marked by
padlock symbol.
Loosen (do not remove) the locking set screw on each
side of the fixture head with the provided Allen wrench.
1
Adjust the Fixture Head
2
ALLEN
WRENCH
SOCKET CAP
SCREW & O-RING
LOCKING
SET SCREW
Adjust the fixture head to the desired position and re-
tighten the set screws to secure in place.
NOTE: Maximum rotation of the fixture head is 300º.
Re-install the O-rings and socket cap screws (reversal of
step 1).
3
4
4B
5A
Use the following instructions along with the provided
template to adjust multiple fixtures to the same angle:
1
Adjust Multiple Fixture Heads
Insert the template in between the head and fixture,
then align the template edge with the fixture edge.
Adjust the head to the desired angle and take note of
the angle using the locking set screw as a guide in
reference to the template.
Adjust the other fixtures to the same angle using the
template and locking set screw as a point of
reference.
a
b
c
TEMPLATE
LOCKING
SET SCREW
A
B
C
TEMPLATE

4

5
90
80
70
60
50
403020100
100
110
120
130
140
150
160170180
FIXTURE HEAD PROTRACTOR TEMPLATE
WARNING: If printing this template, ensure printer settings are set to actual size.

6

7
RECTANGULAR MOUNTING PLATE TEMPLATE
WARNING: If printing this template, ensure printer settings are set to actual size.

8
7400 Linder Ave, Skokie, IL 60077
847.410.4400
www.techlighting.com
© 2018 Tech Lighting, L.L.C. All rights reserved. The "Tech Lighting" graphic is
a registered trademark of Tech Lighting, L.L.C. Tech Lighting reserves the right
to change specifications for product improvements without notification.
A Generation Brands Company
SAVE THESE INSTRUCTIONS!