Volt 3601 Series User manual

VOLT®Low Voltage Landscape Lighting
VOLT®Estate Size Path & Area Lights
3601 Series
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

VOLT®Estate Size Path & Area Lights
3601 Series
Important: Please Read Before Installation
Important Safety Instructions
INSTALLATION INSTRUCTIONS
This xture is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm)
in order to connect to the main low voltage cable.
5. Wiring connections must be made with UL listed wire connectors that
are suitable for outdoor use.
6. Position the wire connector so that it is located within 6 inches (15.2
cm) from a building structure, a luminaire, or tting.
LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.
!
!
www.voltlighting.com
- 2 -

Package Contents
Product Dimensions
A. (1) Fixture Body
[email protected] • 813.978.3700
- 3 -
10.25”
6”
3”
Estate Size Hat featured
on Estate Size Low
Voltage Stem
36”

www.voltlighting.com
INSTALLATION INSTRUCTIONS
- 4 -
Remove Stem Top
1
VOLT®Estate Size Path & Area Lights
3601 Series
Install Lamp
2
Thread the stem top onto the
stem and hand tighten until
snug.
Install Stem Top
3
Stem Top
Stem
Loosen the stem top and remove
it from the top end of the stem.
Stem
Stem Top
Insert the lamp with the correct
wattage and type marked on the
xture label and push rmly into
place.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
Socket
Lamp

[email protected] • 813.978.3700
- 5 -
Install Stake
4
Remove Cap from Stake
5
Dig a hole in the ground for the stake. Slide the stabilizer grid onto the
stake and secure with the screws. Place the stake and backll against
the mounting stake.
Stake
Stabilizer
Grid
Ground Level
Stake
Remove the cap from the stake
by loosening the set screws.
Set Screw
Cap
Stake
Install Cap to Base
6
Screw the coupler on the bottom
center of the base and then
thread the cap onto the coupler.
Base
Coupler

INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 6 -
VOLT®Estate Size Path & Area Lights
3601 Series
Fixture Installation
7
Pass the supply wires through the
stake. Attach the cap with the
xture onto the stake and secure
with set screws. Hand tighten until
snug with a screwdriver.
Set Screw
Cap
Stake Supply Wire
Wire Connection
8
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold separately), connect the leads from the luminaire to the main
supply cable leads.
Pigtail
Main Supply Cable
Wire Connectors

[email protected] • 813.978.3700
- 7 -
Install Hat
9
Place the hat of your choice onto the stem top and secure it with the nial,
or thread the hat of your choice onto the stem top directly. Hand tighten
until snug.
Stem Top
Finial
Hat of your choice
Install/Replace Lamp
Remove the nial, hat and stem top to expose the lamp and replace it
with the correct wattage and type marked on the xture label. Then,
reinstall the stem top, hat and nial.
IMPORTANT: Lamps must be protected from moisture and dust at all
times. Always reinstall the stem top and hat when removed.

is-3601series-ver8.pdf
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 8 -