TECHLIGHTING Voto Pathway User manual

Installation Instructions for
Voto Pathway
920OAVOTO
GP I :ENERAL RODUCT NFORMATION
This product is suitable for wet locations.
12VAC input only.
If using Tech Lighting magnetic transformers, this product be
dimmed with a low-votage magnetic dimmer. For all other
transformers, consult with the manufacturer for compatible
dimmers.
CAUTION RISK OF FIRE-
This product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved.
Use minimum 90°c supply conductors.
OUTDOOR
Loosen the four set screws on fixture(Do Not Remove)
base with the provided Allen wrench and remove the
base plate.
1
Prepare the Fixture
1
700OAVOT_ 1.1
2A
Attach the stake to the base plate by tightly screwing
down the provided stake bolt through the center hole
of the base plate and the stake.
Reattach the base plate assembly to fixture and tighten
down the set screws on the canopy (reversal of Section
1A).
1
STAKE
STAKE BOLT BASE PLATE
2
Install the Fixture using a Stake
(with canopy)
Determine the method of installation:
Install the fixture using a stake , go towith a canopy
Section 2.
Install the fixture using a stake , gowithout a canopy
to Section 3.
Install the fixture , go to Section 4.without a stake
WARNING – Risk of Electric Shock. Install all luminaires
10 feet (3.05 m) or more from a pool, spa, or fountain.
Unit low voltage cable is to:
a) be protected by routing in close proximity to the
luminaire or fitting, or next to a building structure such
as a house or deck;
b) not be buried except for a maximum 6 inches (15.2
cm) in order to connect to the main low voltage cable;
and
c) have the length cut off so that it is connected to a
connector within 6 inches (15.2 cm) from a building
structure, a luminaire, or fitting.
2
1A
ALLEN
WRENCH
1
1
1
1
BASE PLATE
SET SCREW
1

2
2C
6Stake the fixture to the desired location and properly
bury the wire and wire nut connections.
2B
3
4
Bring the power wires to the fixture location in
accordance with local electrical codes.
Connect the white fixture wire to one of the low-
voltage power line wire with the provided outdoor
waterproof wire nut.
Connect the black fixture wire to the remaining low-
voltage power line wire with the provided outdoor
waterproof wire nut.
5
3
5
6
3B
Feed the fixture cord through the bushing and screw the
bushing onto the stem.
Bend the cord into the slot on the bushing and screw the
stake onto the bushing.
Re-tighten the set screw on the stem (reversal of step 1).
3
STAKE
BUSHING
Install the Fixture using a Stake
(without canopy)
7
8
Bring the power wires to the fixture location in
accordance with local electrical codes.
Connect the white fixture wire to one of the low-
voltage power line wire with the provided outdoor
waterproof wire nut.
Connect the black fixture wire to the remaining low-
voltage power line wire with the provided outdoor
waterproof wire nut.
9
7
8
9
3C
4
3A
Loosen the set screw on the stem(Do Not Remove)
using the provided Allen wrench.
Unscrew and remove the canopy from the stem.
1
2
ALLEN
WRENCH
STEM
SET SCREW
1
CANOPY
SET SCREW
3
4
5
5STEM

3
3D
5Stake the fixture to the desired location and properly
bury the wire and wire nut connections.
Install the Fixture to Concrete
(or other hard surfaces)
1
2
Bring the power wires to the fixture location in
accordance with local electrical codes.
Mount the base plate to an even and smooth surface
using the template provided on last page. Ensure that
length of the lag bolts or anchor bolts do not exceed
0.66” from the mounting surface in order to leave
enough clearance for the fixture to fit properly over the
base plate.
1
2
BASE PLATE
4A
0.66”
FIXTURE
BASE PLATE
3
43
4C
Connect the white driver wire to one of the low-voltage
power line wire with a wire nut.
Connect the black fixture wire to the remaining low-
voltage power line with a wire nut.
4
Carefully place the power line/cord inside the fixture,
install the fixture onto the base plate, and secure it in
place by tightening down the set screws.
5
4D
5
SET SCREW
5
ALLEN
WRENCH

RECTANGULAR MOUNTING PLATE TEMPLATE
WARNING: If printing this template, ensure printer settings are set to actual size.
4
7400 Linder Ave, Skokie, IL 60077
847.410.4400
www.techlighting.com
© 2018 Tech Lighting, L.L.C. All rights reserved. The "Tech Lighting" graphic is
a registered trademark of Tech Lighting, L.L.C. Tech Lighting reserves the right
to change specifications for product improvements without notification.
A Generation Brands Company
SAVE THESE INSTRUCTIONS!