Endon EL-40065 User manual

The Light pack contains:
Wall light with separate shade parts.
Terminal block.
The following tools may be required:
Selection of cross and flat head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
Electrical insulation tape.
INSTRUCTION MANUAL
This product is only suitable for connection to a 240V~50Hz supply.
It is recommended that this light is installed by a qualified electrician in accordance with current IEE Wiring
Regulations and local Building Regulations.
The light fitting should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp miniature
circuit breaker).
This light has an IP44 (splash proof) rating suitable for use outdoors.
Run supply wire from a 5-amp electrical supply using double insulated 3-core cable of type H05RN-F 1.0mm2
(not supplied) to selected site, ensuring it is adequately protected through the full length of the cable run, it
must come out of the flat surface of the mounting surface in line with the entry to the fitting.
Except where installed in a conduit or duct , which provides equivalent protection against mechanical damage,
a cable buried in the ground shall incorporate an earthed armour or metal sheath or both, suitable for use as a
protective conductor, or be of insulated concentric construction. Buried cables shall be marked by cable
covers or a suitable marking tape. Buried conduits and ducts shall be suitably identified. Buried cables,
conduits and ducts shall be at a sufficient depth to avoid being damaged by any reasonably foreseeable
disturbance of the ground.
This product contains breakable parts – be careful during handling and maintenance to avoid breakage.
The diffuser (cover) can become hot in use. Switch off and allow 10 minutes to cool before cleaning (using a
dry cloth only – do not use liquid or abrasive cleaners).
If the cover is broken or cracked then it must be replaced immediately to preserve the water ingress
protection, please consult your retailer. This is represented by the symbol
If any modification is made it will invalidate the warranty and may render the product unsafe.
Before you start
Please read these instructions carefully before fitting your new light and retain for reference.
Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker
before commencing installation.
Ensure that no one else has access that would enable the supply to be inadvertently reconnected.
Check the packaging and make sure that you have all the required parts.
Follow each assembly step in order to prevent incorrect assembly
Make sure all screws / nuts, including electrical connections etc are fully tightened before use.
EL- 40064, EL- 40065 and EL- 40066 Outdoor wall fittings.
Safety Warnings

Endon Lighting Ltd
Leeds
UK
LS9 0SE
These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.
.
Assembly / user instructions
N210 102v1
Diagram A
Diagram B
Diagram C
1. Diagram A. Remove the back plate by undoing the 2
decorative nuts from the threaded bolts. Unscrew the
glass cover. Secure the 2 sections of the shade onto
the lamp holder housing with the screws provided.
2. Diagram B. Fit the 2 threaded posts in the back plate
and bring the mains cable through the rubber
grommet then use the back plate as a template and
mark the 2 fixings holes, making sure the back plate
is correctly aligned so that the threaded bolts are
horizontal. Use appropriate fixings to secure the back
plate to the wall.
3. Diagram C. Connect the house wiring to the internal
terminal block. The cable entry grommet must be
securely in place to ensure that the water ingress
protection is maintained. NOTE: This is a Class I
fitting and must be earthed. Connect the incoming
mains as per the diagram.
4. Diagram D. Fit the terminal block onto the post in the
back plate and then fit the front frame over the 2
threaded bolts in the back plate and secure with the 2
decorative nuts. Take care not to trap or strain the
internal cables.
5. Fit the appropriate bulb into the lamp holder NOTE:
Never fit bulbs of a higher wattage than those
specified on the label (as these may cause
overheating and damage the fitting).
6. Fit the glass cover making sure any seals are
replaced.
7. Turn on the power and test.
Diagram D
Fixing screws
Threaded bolts
Terminal post
Decorative nuts
Glass cover