Technaxx TX-227 User manual

1
Model: TX-227,TX-230 Article No. 5039,5042, 04/2023
Technaxx® * User Manual
Balcony power station mount 300W TX-227
Balcony power station mount 600W TX-230
Before using the appliance for the first time, please read the instructions for use and
safety information carefully.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capacities, or by persons lacking in experience or
knowledge, unless they are supervised or instructed on the use of this device by a
person responsible for their safety. Children should be supervised to ensure they do
not play with this device.
Keep this user manual for future reference or product sharing carefully. Do the same
with the original accessories for this product. In case of warranty, please contact the
dealer or the store where you bought this product.
Enjoy your product. * Share your experience and opinion on one of the well-
known internet portals.
Specifications are subject to change without notice - please be sure to use the latest
manual available on the manufacturer's website.

2
Model: TX-227,TX-230 Article No. 5039,5042, 04/2023
Table of Contents
Important notes at the start ................2
Safety instructions..........................2
Optical conspicuities / scratches in
the materials...................................3
Disclaimer ......................................3
Features ............................................3
Scope of delivery ...............................4
TX-227 ...........................................4
TX-230 ...........................................4
Product overview ...............................5
Installation..........................................6
Assembly (35°)...............................6
Fixing solar module to mount..........8
Mount to balcony railing......................8
Mount U-profile to balcony railing....9
Flat roof (bitumen roof), terrace (free
standing) ..........................................10
Wall mounting...................................12
Angle adjustment..............................12
Technical specifications....................13
Support ............................................13
Maintenance.....................................13
Disposal ...........................................13
Important notes at the start
Safety instructions
⚫ This product is not a toy. Keep it out of the reach of children.
⚫ These operating instructions are intended to familiarize you with the operation of
this product. Therefore, keep these instructions in a safe place so that you can access
them at any time. Pass them on to subsequent users.
⚫ Observe the safety instructions during use.
⚫ Conversion or modification of the product will impair product safety. Attention Risk
of injury! Attention loss of warranty!
⚫ The product is statically tested for loads of wind load zone 2 and snow load zone 2.
Wind or/and snow loads exceeding the values of these zones have not been tested
and may cause damage to the product or/and the mounting location.
⚫ Check in advance whether the static conditions of your balcony railing/roof/wall/floor
are sufficient to support additional loads. Check your state building code (LBO) for
requirements for the erection of plants and systems.
⚫ Make sure all screws and fasteners are properly fastened before mounting/hanging
the solar module. If screws are loose, there is a risk that the solar module may fall
down and create a dangerous situation under the balcony. Use a torque wrench or
socket wrench to make sure it is tight.
⚫ Do not exceed these values for the screws: M8 screws: 11±1 N*m
⚫ Use at least 2 people to lift and install the solar modules.
⚫ Make sure that the bracket is fixed on the top as well as on the bottom of the
balcony, so that it can withstand stormy weather.
⚫ Make sure that the mounting surface is strong enough to support the weight and
load of the mount including solar module.
⚫ Handle the product with care. It can be damaged by shocks, impacts or falling from

3
Model: TX-227,TX-230 Article No. 5039,5042, 04/2023
even a low height.
⚫ Mounting the bracket on a vehicle roof is prohibited for safety and structural
reasons.
⚫ Technical changes and errors excepted.
Optical conspicuities / scratches in the materials
⚫ Visual conspicuities or scratches on the fixture due to industrial production or/and
transport are not defects and will not be recognized as such.
⚫ Possible conspicuities in the surface finish do not affect the safety or functionality
of the overall system.
Disclaimer
⚫ In no event shall Technaxx Deutschland be liable/responsible for any direct, indirect
punitive, incidental, special consequential danger, to property or life, improper
storage, whatsoever arising out of or connected with the use or misuse of their
products.
⚫ Technaxx Germany assumes no liability for material damage caused by improper
installation or non-observance of the installation instructions.
Features
⚫ Easy assembly
⚫ Made in Germany
⚫ DGS certified
⚫ Static tested bracket
⚫ 3 mounting options (balcony (round+4Kant), free-standing, wall-mounting)
⚫ 3 adjustable mounting angle (30°, 35°, 40°)
⚫ High quality 6mm aluminum profile

4
Model: TX-227,TX-230 Article No. 5039,5042, 04/2023
Scope of delivery
TX-227
•2x Alu-profile (long, 105cm)
•2x Alu-profile (short, 95cm)
•2x Alu-profile (angle, 51cm)
•4x Alu-U-profile
•22x Hex nut M8
•4x Rubber strip
(2mm 120x140mm)
•4x Plastic shim plate
(5mm 120x56mm)
•4x Hexagon head screw M8 x20
•8x Star screw M8x30
Additionally needed:
•Solar module
Optional accessory for:
•TX-212
•TX-213
TX-230
•4x Alu-profile (long, 105cm)
•4x Alu-profile (short, 95cm)
•4x Alu-profile (angle, 51cm)
•8x Alu-U-profile
•44x Hex nut M8
•8x Rubber strip
(2mm 120x140mm)
•8x Plastic shim plate
(5mm 120x56mm)
•8x Hexagon head screw M8 x20
•16x Star screw M8x30
Additionally needed:
•Solar module
Optional accessory for:
•TX-220
•TX-228
Alu-profile
(long)
A
Alu-profile
(short)
B
Alu-profile
(angle)
C
Alu-U-
profile
D
Hex nut M8
E
Hexagon
head screw
M8 x20
F
Star screw
M8x30
G

5
Model: TX-227,TX-230 Article No. 5039,5042, 04/2023
Rubber
strip
H
Plastic shim
plate
I
Product overview
* Solar module not included
1
Alu-profile (long)
5
Angle adjustment hole 35°
2
Alu-profile (short)
6
Angle adjustment hole 40°
3
Alu-U-profile
7
Inverter mount screws
4
Angle adjustment hole 30°
8
Alu-profile (angle)

6
Model: TX-227,TX-230 Article No. 5039,5042, 04/2023
Installation
Assembly (35°)
Note: For the assembly is a 13mm wrench needed.
Material overview
Step 1
The illustration shows the parts needed
for one leg of the bracket. You need to
perform Steps 1-3 two times to build the
TX-227 and four times for TX-230.
Put parts A and B together at the upper
screw. Use an M8 hex nut to secure
them. Do not tighten them yet.

7
Model: TX-227,TX-230 Article No. 5039,5042, 04/2023
Step 2
Step 3 (only for balcony railing)
Use part C and insert it into the hole of B
and the middle hole of A to mount the
bracket for the 35° angle. Secure part C
with two M8 hex nuts. Tighten the nuts
with a 13 mm wrench.
Tighten the M8 hex nut from Step 1 now
as well.
Attach part D to the top of part B. Secure
part D with two M8 hex nuts. Tighten the
nuts with a 13 mm wrench.
The lower part D can be attached to part
B, but must be detached again when the
mount is hung on the balcony railing.

8
Model: TX-227,TX-230 Article No. 5039,5042, 04/2023
Fixing solar module to mount
⚫ These installation instructions are only intended to describe the installation.
⚫ Be at least 2 people to lift and mount the solar modules.
⚫ Use 4x hexagon head screw M8x20 to mount the solar module to the mount as
shown above.
⚫ Do not stand on the module or the module frame.
⚫ To prevent grease stains on the module, avoid contact with your hands on the glass
surface and ideally wear work gloves.
⚫ Lay the solar module flat on clean surface. Best is to use some protection like a
blanket or cardboard in the size of the module underneath. Be careful not to damage
the glass front.
⚫ Lay the mount on the holes of the solar module you want the mount to be attached
to. First fix the single hole and tighten the hexagon head screw M8x20 with an M8 hex
nut.
⚫ After that fix the hexagon head screw M8x20 to the slotted hole and tighten the M8
hex nut.
Mount to balcony railing
⚫ The solar module is only suitable for installation up to a height of 4m (upper edge
of the module), provided that there is also no public traffic below the module.
⚫ The mounting angle (30°, 35°, 40°), the orientation (west, south, east) as well as
the geographical location influence the yield of the balcony power plant.
⚫ Refer to the technical specifications for maximum wind and snow loads.
⚫ Choose a suitable location for the installation of the solar system, free from
obstacles and with enough space to allow you to adjust the tilt angle (if necessary).
⚫ Be at least 2 people to lift and mount the solar modules.

9
Model: TX-227,TX-230 Article No. 5039,5042, 04/2023
Mount U-profile to balcony railing
⚫ Lay the rubber strip onto the place of the balcony railing where the holder will be
placed. The Rubber strip is to protect the railing.
⚫ Hang the whole solar module onto the balcony railing by help from a second person.
⚫ Now screw in the star screw with an attached Hex nut M8 into the both holes of the
U-profile. The Hex but M8 is for counter.
⚫ Place the plastic shim plate between the star screws and the rubber strip on the
railing.
⚫ Fix the plastic shim plate by gently tightening the star screws.
⚫ Now repeat the procedure for the lower U-profiles.
⚫ Check the pictures below for correct mounting.
⚫ Tighten all star screws and lock them with the M8 hex nut.
Note: Make sure that the bracket at the bottom of the balcony is also mounted and
secured to avoid problems in stormy weather and to ensure that the module cannot
move under any circumstances.
1
2
3

10
Model: TX-227,TX-230 Article No. 5039,5042, 04/2023
Flat roof (bitumen roof), terrace (free standing)
⚫ Choose a suitable location for the installation of the solar system, free from
obstacles and with enough space to allow you to adjust the tilt angle (if necessary).
⚫ Be at least 2 people to lift and mount the solar modules.
⚫ The mounting angle (30°, 35°, 40°), the orientation (west, south, east) as well as
the geographical location influence the yield of the balcony power plant.
⚫ The statics of the roof for the photovoltaic system must be checked by the customer.
The photovoltaic system can be installed up to a roof height of 9m, a sea level of max.
350 m and a roof pitch of 45°.
⚫ We recommend a distance of 1.25 m to fire walls of adjacent buildings (e.g. row
houses). For more detailed requirements for your federal state, refer to your state
building code (LBO).
⚫ Make sure that national and site-specific building regulations, occupational safety
and accident prevention regulations, standards and environmental protection
regulations are observed.
Note: In the case of a flat or bitumen roof fastening, the use of screws is not
recommended. The screws would damage the seal of the roof and the roof could leak.
Weighing down the module support
⚫ The solar module (up to 19kg) should be positioned at ground level or centered on
a flat roof.
⚫ Suitable is a bracket for mounting on bitumen, concrete, in the garden on the lawn
or terrace.
⚫ The weighting is calculated according to the terrain IV (urban area), where at least
15% of the area is covered with buildings, the average height of which exceeds 15m,
and may differ for other heights or terrain structures.
⚫ In case of installation on a flat roof, the top edge of the building should be lower
than 15m and the photovoltaic system should be at least 1.25m away from the
neighbor's roof surface. The maximum slope of the ground may be 5°.
⚫ One concrete slab should weigh 9kg.
⚫ Check whether the statics of the installation site are suitable for the photovoltaic
system. Technaxx Germany does not assume any liability for the suitability of your
installation site.