TechNexion PICO-NYMPH-IMX6 User manual

PICO-NYMPH-IMX6
Quickstart Guide
INNOVATORS OF TECHNOLOGY
2Dimensions
1 Safety Precauons
Thank you for purchasing a TechNexion PICO series pre-assembled evaluaon kit based on NXP i.MX6 applicaons
processor. This installaon guide will be helpful in the installaon, wiring and inspecon of your TechNexion
evaluaon kit. Before using the product, please read this guide to ensure correct use. You should thoroughly
understand all safety precauons before proceeding with the installaon, wiring, and operaon. Place this
instrucon sheet in a safe locaon for future reference.
• Keep the device dry. Precipitaon, humidity, and all types of liquids or moisture can contain minerals that will
corrode electronic circuits. If your device does get wet, allow it to dry completely.
• Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be damaged.
• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage
baeries, and warp or melt certain plascs.
• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form
inside the device and damage electronic circuit boards.
• Do not aempt to open the device.This product needs to be installed by qualified personnel.
• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.
• Do not paint the device. Paint can clog the parts and prevent proper operaon.
• Unauthorized modificaons or aachments could damage the device and may violate regulaons governing radio
devices.
•Do not touch any internal or exposed parts of the device as electrical shock may result.
•Do not open the device while power is on. Otherwise electrical shock may result.
•Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
•Be sure the venlaon holes are not obstructed during operaon. Otherwise malfuncon may result due to bad
venlaon or overheang.
These suggesons apply equally to your device, baery, charger, or any enhancement. If any device is not
working properly, take it to the nearest authorized service facility for service.
• Make sure that the available power source matches the required input power of the device. Failure to observe
this cauon may result in electric shock or fire.
1.1 Storage and Installaon
1.2 Wiring
1.3 Maintenance and Inspecon
!
Unit : mm
1 2
104
34.8 90.02
80.92
36.9
34.8
36.9

3External Connectors
Le side view:
Right side view:
• All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a retrieval system, or transmied, in any
form or by any means whether, electronic, mechanical, or otherwise without the prior wrien permission of TechNexion Ltd.
• No warranty of accuracy is given concerning the contents of the informaon contained in this publicaon. To the extent permied
by law no liability (including liability to any person by reason of negligence) will be accepted by TechNexion Ltd., its subsidiaries or
employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.
• TechNexion Ltd. reserves the right to change details in this publicaon without noce. Please download the most updated version
at: hps://www.technexion.com/support/download-center/
Description No.No. Description
1 LAN RJ45 connector
Antenna connector
CTIA compliant 3.5mm audio jack
VGA (15-pin D-SUB) connector
USB Host connector
HDMI connector
Power Input connector
Antenna hole
Optional connector hole
USB OTG (Type-C) connector
Antenna hole
MicroSD cardslot
Optional connector hole
Micro-SIM cardslot
Antenna hole
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Phone: [phone]
Web: www.technexion.com
16F-5, No. 736, Zhongzheng Road,
ZhongHe District, 23511, New Taipei City, Taiwan
© 2001-2019 TechNexion Ltd.
2019-06-11
The unit is preloaded with soware that can download and install a selecon of OS images over hardwired network.
Simply connect a display to the unit though the VGA or HDMI connector and a network through the Ethernet LAN
RJ45 connector and power it up, then follow the steps on the screen to load the soware. Local proxies will interfere
with this process. For more informaon, go to our Knowledge Base at: hps://www.technexion.com/support/knowl-
edge-base/
5 Soware Installaon
3 4
4.1 Wi-Fi antenna
4 Installaon Instrucons
This installaon guide will help you to assemble your development kit using step-by-step instrucons to make sure
all parts (development board and Wi-Fi antenna) are working.
Tips: Do not power your board during the installaon process
Please follow the steps below to properly install the Wi-Fi antenna.
Step 1: Prepare Wi-Fi antenna and development board.
Step 2: Locate the round Wi-Fi antenna connector on the development board.
Step 3: Screw the base of the Wi-Fi antenna into the antenna connector.
12 3
Top side view:
2 3 4 567 1
8 9 10
11 12 13 14 15