Tecnoinox CP8FE7 User manual

CP8FE7
FREESTANDING 24+24LT GN2/3 ELECTRIC PAST A COOKER ON CLOSED
CABINET - BASKETS NOT INCLUDED
716060
CODE
DESCRIPTION
MODEL
13-03-2023 14:10

EN - 1
5410.345.01
Part 1
Installation
ELECTRIC PASTA COOKER
General warnings
The manufacturer declines any
liability for damage caused by improper or
incorrect appliance installation or
maintenance, or failure to observe the
safety regulations.
The appliance referred to in this
instruction manual has been manufactured
in conformity with the requirements of the
European Directives on Low Voltage and
Electromagnetic Compatibility.
The appliance must be installed by a
qualified technician according to the
regulations and directives in force in the
country of use, following the instructions in
this manual.
This appliance has been designed
exclusively to cook food in professional
kitchens such as those in restaurants,
canteens and hotels. This appliance is not
designed for mass, continuous food
production. All other uses are considered
improper
The appliance must never be left
unattended when it is being used.
The appliance must be installed so as
to prevent boiling water from coming into
contact with surrounding hot oil.
The appliance is designed for
professional use and therefore should only
be used by qualified personnel.
Do not use the appliance with no
water in the cooking tank.
Be careful when using the appliance
because the cooking surfaces are very hot.
The appliance should be installed
under an extractor hood for evacuating
cooking vapours.
Install the appliance on a floor or flat
surface. Avoid slopes of more than 5° to
keep it stable.
Whenever the appliance is moved, for
example to be transported, written off and
scrapped, take care not to tilt the appliance
more than 5°, to keep it stable.
The appliance, and especially the
power cord, must not be installed near heat
sources
The temperature of the environment
in which the appliance is installed must not
exceed 50°C.
Do not open the control panel or
touch the electrical components. Contact
the technical support service
If the power cable is damaged it must
be replaced by the manufacturer, by
technical support, or by a similarly qualified
person, in order to avoid any hazards.
Switch the appliance off during
maintenance or when parts are being
replaced.
When using the appliance, wear oven
gloves and clothing that covers the entire
body.
Switch the appliance off in the event
of a fault or malfunction.
Please be extremely careful and
contact the technical support service if any
parts or components come loose.
The appliance should be checked
once a year by a qualified technician.

EN - 2
5410.345.01
If the appliance is installed in line:
Respect the minimum clearance
distance of 80 mm between the appliance
and any walls made of flammable material,
partitions, kitchen furniture or nearby
equipment.
The surfaces in contact with the
appliance must be covered with a non-
combustible heat insulation material such
as mineral wool, glass wool or ceramic fibre.
Connection to the mains
Remove the appliance packaging as well as the protective plastic
sheet. If necessary, remove any traces of glue with a suitable
solvent. Please comply with local legal provisions when disposing
of the packaging.
When installing the appliance, the following regulations must be
observed:
Applicable national laws in force;
Regional and/or local regulations, such as building
regulations;
Directives and regulations stipulated by the local electricity
supplier;
Accident prevention regulations in force;
Fire prevention regulations;
Relative IEC Regulations (only in Italy).
Before connecting the electrics, take note of the technical
specifications such as voltage, frequency, number of phases and
power required for installation. This information can be found on
the appliance rating plate.
Power supply features:
The alternating current power supply to the unit must meet the
following conditions:
Maximum voltage variation ± 10%
Maximum frequency change ± 1% in continuous ± 2% for a
short period of time.
The appliance power supply must be protected against
overcurrent (short circuits and overload) with fuses or properly
sized circuit breakers.
The installer must connect up the appliance by positioning an
easily accessible main switch that disconnects all poles supplying
electrical power to the appliance. When contacts are open, there
must be a minimum distance of 3 mm between the poles.
The cable:
must not be installed near heat sources and the ambient
temperature of the surrounding environment must not
exceed 50°C
must be protected by a rigid metal or plastic tube.
must meet H07 RN-F standards as a minimum.
must have a minimum cross section as indicated on the cover.
To access the “M” terminal board, remove the control panel by
loosening the screws on the panel. Connect the power cable
wires to the terminal board by following the instructions provided
in the wiring diagram.
The appliance must be connected to an efficient earth. Connect
the earth conductor to the screw marked with the symbol “ ”
close to the connection terminal board.
The appliance must also be included in an equipotential bonding;
this connection is made with a screw marked with the symbol
on the bottom of the appliance. The equipotential wire must
have a cross section of 10 mm2.
The manufacturer declines any
liability for damage caused by improper or
incorrect appliance installation or
maintenance, or failure to observe the
safety regulations.
Connection to the water supply
The equipment must be supplied with drinking water at a
pressure of at least 1.5 bar. Connect the water inlet pipe by first
placing a water shut-off valve and a mechanical filter.
EXHAUST:
The water must be evacuated from the drain collector located
under tap “C” (fig.2).

EN - 3
5410.345.02
Part 2
Use
General warnings
The appliance is designed for
professional use and therefore should only
be used by qualified personnel.
Be careful when using the appliance
because the cooking surfaces are very hot.
The appliance must never be left
unattended when it is being used.
Switch the appliance off in the event
of a fault or malfunction.
Do not use the appliance with no
water in the cooking tank.
Commissioning
FILLING THE TANK:
Check that the water drain tap inside the appliance is closed
(lever in horizontal position).
Fill with water up to the level marked on the tank “L” (fig.2).
Fill the tank with water by opening tap “W” (fig.2); the water will
enter the tank directly from the supplier.
•In models CP_FE7 and CP_FE9 tap “W” is located inside
the compartment, under the control panel.
•In models CP35E_ and DCP35E_ tap “W” is on the
control panel.
You can estimate the maximum quantity of food allowed in kg as
a tenth of the amount of water in the cooking tank.
Switching on standard models
1. Press the switch above the appliance.
2. Turn knob “A” (fig.4) to align the control panel index with the desired power level.
3. The green pilot light comes on to indicate that there is power “S” (fig.3).
Knob position Power (CP35E_;
DCP35E_)
Power (CP_FE7) Power (CP_FE9) Type of use indicated
0 - - - Off
1 1.6 kW 2 kW 3 kW Keeping warm
2 3.2 kW 4 kW 6 kW Cooking
3 4.8 kW 6 kW 9 kW Fast heating / Boiling
Turning the appliance off
Turn the knob (fig.4) to “0”.
Disconnect the switch above the appliance.
Draining the tank
After turning off the appliance, empty the tank by opening tap “C” (fig.2). (lever in vertical position).
Safety thermostat
The appliances have a safety thermostat that cuts off the electric
power supply in case of a fault.
To turn the appliance on again, press the “E” button.
Contact a specialist technician.

EN - 4
5410.345.02
Part 3
Maintenance and cleaning
Cleaning and care
Do not wash the appliance with jets
of water because if water enters the electric
components it could lead to a malfunction.
Cleaning operations must only be
carried out once the appliance has cooled.
Only use products that are food safe.
Use personal protective equipment
(PPE) when cleaning.
Keeping the appliance clean is very important for a long and
trouble-free product life. Wash the removable parts separately in
warm water and detergent, then rinse them with running water.
Do not use harsh or abrasive detergents to clean the stainless
steel parts. Iron cleaning pads should not be used as they may
cause rust to form. For the same reason, avoid contact with
ferrous materials. When cleaning, avoid using abrasive paper or
cloth; for stubborn deposits, use a sponge (e.g. Scotch-Brite). You
can also use oven and grill cleaning sprays, readily available on
the market, to remove stubborn deposits. If you use spray
products, please follow the manufacturer’s instructions. To
minimise emissions of polluting substances into the environment,
clean the appliance with products that are at least 90%
biodegradable. If the appliance will remain inactive for a
prolonged period of time, clean it then apply a thin layer of
protector spray (widely available on the market) to the external
surfaces.
What to do in case of malfunctioning
Malfunctions are not always due to the quality of the
components used. These appliances are manufactured using top
quality components. Malfunctions may be caused by voltage
surges or by infiltrations of dust and/or dirt.
In the event of abnormal operation,
disconnect the appliance from the mains
and contact the authorised repair service.
Unauthorised persons should never
attempt to repair the appliance, or carry out
maintenance. Tampering with the
appliance invalidates the warranty.
Maintenance
The appliances do not require any special maintenance other than normal cleaning.
The appliance should be checked once a year by a repair service. Please stipulate a maintenance contract.
MAINTENANCE - TESTS - CHECKS - CLEANING FREQUENCY USER REPAIR SERVICE
Cleaning General cleaning of the appliance and the
surrounding areas
Daily or based on the
degree of use Yes -
Safety devices Check the safety devices function correctly Monthly Yes Yes
Mechanical protective devices Check condition; check that there are no
deformations, or loose or missing parts. Monthly Yes Yes
Controls Check the readability and condition of the
inscriptions and symbols, and repair if necessary. Yearly Yes Yes
Structure of the appliance
Check the mechanical part to make sure that it is not
broken or deformed; tighten the screws. Yearly
Yes Yes
Tighten the main bolts (screws, fasteners, etc.) on the
appliance - Yes
Safety signs Check the readability and condition of the safety
signs. Yearly Yes Yes
Electrical control panel /
electronics
Check the condition of the electrical parts installed
on the electrical control panel. Yearly - Yes
Check the wiring between the electrical panel and
the parts of the appliance.
Electrical connection cable and
plug socket
Check the condition of the connection cable and
plug socket. Yearly Yes Yes
Replace if defective. - Yes
Motor bearings (if present) Replace motor bearings Every three years - Yes

EN - 5
5410.345.02
Ecology and the environment
Our appliances have been studied and optimised via testing to
provide high performance and yields. In order to reduce energy
consumption (electricity, gas and water), do not use the
appliance for long periods of time without food inside or in
conditions that may compromise optimum yield.
All of the following materials are used for the packaging:
• Polyethylene: external packaging film and/or bubble wrap
• Polypropylene: straps
• Expanded polystyrene: corner pieces, protective sheets and
blocks
• Cardboard
• Wooden base frame
These materials are environmentally friendly and can be safely
stored or reused/recycled. Should you wish to dispose of them,
please adhere to the waste regulations in force in your country.
Dispose of the appliance responsibly at the end of its
useful life.
In compliance with the regulations in force in your
country, before disposing of the waste product,
please remove the power cable. Then take the appliance to an
authorised collection and treatment site.