TECOM M13 User manual

M13 Video Door Phone
User Manual
(Draft)
V0.7
By Kevin Tsou
20140707

M13 IP Video Door Phone Features

M13 Video door phone features
IP addressable video door station
DI / DO dry control for door release
Digital color video camera, NTSC / PAL
Call button, LED indication
Built-in RFID sensor module
Uses 12~24V DC power supply
Door Phone unit
IP addressable
Wall mount
Flush mount

The Front-View of the M13 Video door phone
• The figure below illustrates the front view of the M13. With the point numbers,
you can find its name and a simple description of the part in the following table.
(Wall Mount Type)
(Flush Mount Type)

The Back-View of the M13 Video door phone
(Wall Mount Type) (Flush Mount Type)

M13 Video Door Phone Hardware Installation

M13 Connection
•Connect video door phone to IG7600’s LAN port
directly.
•Connect video door phone to IG7600’s LAN
port via network switch.
The M13 video door phone only can be registered via IG7600’s LAN port. Please
connect M13 video door phone to IG7600’s LAN port directly or via a network switch.
IMPORTANT: Disconnect the IG7600 (and Network switch ) power when M13 video door
phone is wiring. Keep power off until the wire connection has been made.

Cat.5e Ethernet Cable
Cat.5e Ethernet Cable
Cat. 5e Ethernet cable can be used to connect M13 video door phone and IG7600.
Cat. 5e Ethernet cable resistance - less than 0.094 Ohm/m.
The maximum connection distance cannot exceed 100 meters. When the
distance exceeds 100 meters, an individual switch/hub is needed to connect
M13 video door phone and IG7600.

M13 Connecter
• 14 pin connecter with RJ45 and DC plug (Default)
• 14 pin connecter without Jack
• Twist pair definition:
• Pair1 : Pin1 & Pin 2.
• Pair2 : Pin3 & Pin 4.
• Pair3 : Pin5 & Pin 6.
• Pair4 : Pin7 & Pin 8.
Color of Wire and Identification

RJ-45 Connector & Cat 5e Ethernet Cable.
•RJ45 jack:
Wiring: CAT5e connect to 14 pin connecter of M13

M13 Power Supply Connection
Please choose from the two following options how to connect M13
to power supply
1. M13’s DC jack connected with power adaptor
In case power supply is available at the spot of M13 installation, please use
the adaptor to connect the door station to power supply.
2. M13 power connected via power wires of Ethernet cable
In case there is no power supply source available at the spot of M13
installation, please use Ethernet cable power wires to connect the door
station to the power adapter as shown on the picture below.

M13’s DC jack connection with power adaptor
• Use an external power adaptor to M13 video door phone.
Cat 5e Ethernet Cable
M13
Switch
Or
IG7600 LAN port
Power
12V-24V
To connect to the external power adaptor (DC 12V/2.0A ~ 24V/1.0A )
DC jack

M13 power connection via power wires of Ethernet cable
• Connect power adaptor via power wires of Ethernet cable.
M13
•The blue and white/blue wires connect
to DC “+” wire of power adaptor.
+
-
Power
12-24V
•The brown and white/brown wires connect
to DC “-” wire of power adaptor.
To avoid possible shorts that may occur, please
do protection for each wire.
Switch
Or
IG7600 LAN port
Cat 5e Ethernet Cable
• Based on different length of Cat. 5e Ethernet cable, you should use different voltage
output power adaptor to ensure M13 video door phone work well.
Length <= 30m : Use 12V/2A power adaptor
Length <= 100m : Use 24V/1A power adaptor

Power source reference for electric strike/lock
Electric Strikes provide remote release of the locked
door. They allow the door to be opened without
retracting the latch bolt.
This occurs by releasing of the electric strike lip
(sometimes called keeper or gate). When the door
closes the beveled latch bolt rides over the lip and
falls into the electric strike pocket.
The relay of the outdoor phone can switch the
external power to electronic lock.
The ground pin of external device should be
connected to "GND"( pin 10, black ) for common
ground.
On loss of power, the strike/lock is locked
another supply is required to power the door strike.
Electric mortise lock
Electric strike

Connections to electric strike (reference )
The connectivity point defined on door phone for electronic door strike/lock is in accordance with – PT, AC, EL.
Fail-Secure Door Lock
* When Lock on, SW1 → open
* When Lock open, SW1 → close
2KΩ1/4W
+
-
V=DC +24V
External Power supply
C
EL
PT
SW1
PTCOM
R- NO
New back panel
With RJ45 connector
& wire set
NOTES
•Connect to the electric door strike according to its specifications.
•Do not use the unoccupied terminals and ports for other purposes.
•In order to prevent miswiring, label both ends of each cable with the unit and terminal names
to which they are to be connected.
•For connecting other manufacturer’s products, refer to the instruction manuals for those
products.
•The illustration of the unit’s rear panel differs from the actual one. This is for simplifying the
connection diagram.
Electric strike

Connections to electric mortis lock (reference )
The connectivity point defined on door phone for electronic door strike/lock is in accordance with – PT, AC, EL.
NOTES
•Connect to the electric door strike according to its specifications.
•Do not use the unoccupied terminals and ports for other purposes.
•In order to prevent miswiring, label both ends of each cable with the unit and terminal names to
which they are to be connected.
•For connecting other manufacturer’s products, refer to the instruction manuals for those products.
•The illustration of the unit’s rear panel differs from the actual one. This is for simplifying the
connection diagram.
Electric mortise lock

Gecko into the wall, locked the Wall mount frame
Mounting & surface wiring (Wall mount type)
Pull the wire from the Wall,
Wire connected with door phone unit
Cable set connected to the back panel of door phone
unit.
Cable set with RJ45
connector & wire set

Complete the installation (Wall mount type)
The M13 outdoor phone will be pressed into the wall mount and use the fixed star screws
and wrench
Cleaning: Clean the units with a soft cloth dampened with a neutral household cleanser.
Do not use an abrasive cleanser or cloth.

M13 Dimension (flush mount type)
Side view with back bracketFront panel

M13 Assembly (flush mount type)
Main body
Face panel
Back bracket
Cable set with RJ45
connector & wire set
Take off dust cap