TECshow iON 230B User manual

USER MANUAL
Read the user manual before turning on the product.

!
!
1!
Every person involved with the installation, operation and maintenance of this device has to
- be qualified
- follow the instructions of this manual
- consider this manual to be part of the total product
- keep this manual for the entire service life of the product
pass this manual on to every further owner or user of the product
download the latest version of the user manual from the Internet
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the
housing!
For your own safety, please read this user manual carefully before you initially start-up.
INTRODUCTION
Thanks for choosing a TECSHOW product. ION Series is built to satisfy the most demanding users. We are
confident that our excellent products and service will satisfy you.
Unpack the device you will find following items inside the box:
1. The fixture device
2. User manual
3. Omega holder with quick-lock fastener
4. DMX cable 3m
5. PowerCon power supply cable 1.5m
6. Safety rope
SAFETY INSTRUCTIONS
This device has left our factory in absolutely perfect condition. In order to maintain this condition and to ensure
a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this user manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer
will not accept liability for any resulting defects or problems.
CAUTION!
Be careful with your operations. With a dangerous voltage you can suffer a dangerous
electric shock when touching the wires

!
!
2!
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until it
has reached room temperature.
Please make sure that there are no obvious transport damages. Should you notice any damages on the A/C
connection cable or on the casing, do not take the device into operation and immediately consult your local
dealer.
This device falls under protection-class I. The power plug must only be plugged into a protection class I
outlet. The voltage and frequency must exactly be the same as stated on the device. Wrong voltages or
power outlets can lead to the destruction of the device and to mortal electrical shock.
Always plug in the power plug last. The power plug must always be inserted without force. Make sure that the
plug is tightly connected with the outlet.
Never let the power-cord come into contact with other cables! Handle the power-cord and all connections
with the mains with particular caution! Never touch them with wet hands, as this could lead to mortal
electrical shock.
Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never operate next
to sources of heat or cold. Disregard can lead to power cord damages, fire or mortal electrical shock.
The cable insert or the female part in the device must never be strained. There must always be sufficient
cable to the device. Otherwise, the cable may be damaged which may lead to mortal damage.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the
power-cord from time to time.
If extension cords are used, make sure that the core diameter is sufficient for the required power consumption
of the device. All warnings concerning the power cords are also valid for possible extension cords.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power-cord by the plug. Never pull out the plug by tugging the power-cord. Otherwise, the cable or plug can
be damaged leading to mortal electrical shock. If the power plug or the power switch is not accessible, the
device must be disconnected via the mains.
If the power plug or the device is dusty, the device must be taken out of operation, disconnected and then be
cleaned with a dry cloth. Dust can reduce the insulation which may lead to mortal electrical shock. More
severe dirt in and at the device should only be removed by a specialist.
There must never enter any liquid into power outlets, extension cords or any holes in the housing of the
device. If you suppose that also a minimal amount of liquid may have entered the device, it must immediately
be disconnected. This is also valid, if the device was exposed to high humidity. Also if the device is still
running, the device must be checked by a specialist if the liquid has reduced any insulation. Reduced
insulation can cause mortal electrical shock.
There must never be any objects entering into the device. This is especially valid for metal parts. If any metal
parts like staples or coarse metal chips enter into the device, the device must be taken out of operation and
disconnected immediately. Malfunction or short-circuits caused by metal parts may cause mortal injuries.
HEALTH HAZARD!
Never look directly into the light source, as sensitive persons may suffer an
epileptic shock (especially meant for epileptics)!
Keep away children and amateurs!
Never leave this device running unattended.

!
!
3!
OPERATING DETERMINATIONS
This device is a moving-head lighting effect for creating decorative effects. This product is only allowed to be
operated with an alternating voltage of 100-240 V, 50/60 Hz and was designed for indoor use only.
This device is designed for professional use, e.g. on stages, in clubs, bars, theatres etc.
Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
Do not shake the device. Avoid brute force when installing or operating the device.
Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged. Always hold the
fixture at the transport handles.
When choosing the installation-spot, please make sure that the device is not exposed to extreme heat,
moisture or dust. There should not be any cables lying around. Please make sure that the unit cannot be
touched or bumped.
This device must never be operated or stockpiled in surroundings where splash water, rain, moisture or fog
may harm the device. Moisture or very high humidity can reduce the insulation and lead to mortal electrical
shocks. When using smoke machines, make sure that the device is never exposed to the direct smoke jet and
is installed in a distance of 0.5 meters between smoke machine and device. The room must only be saturated
with an amount of smoke that the visibility will always be more than 10 meters.
The ambient temperature must always be between -15° C and +45° C. Keep away from direct insulation
(particularly in cars) and heaters.
The relative humidity must not exceed 50 % with an ambient temperature of 45° C.
This device must only be operated in an altitude between -20 and 2000 m over NN.
Never use the device during thunderstorms. Over voltage could destroy the device. Always disconnect the
device during thunderstorms.
The symbol
- - -m determines the minimum distance from lighted objects. The
minimum distance between light-output and the illuminated surface must be more than this value.
The device must only be installed on a non-flammable surface. In order to safeguard sufficient ventilation,
leave 50 cm of free space around the device.
The housing must never touch surrounding surfaces or objects.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fixture.
For overhead use (mounting height >100 cm), always fix the fixture with an appropriate safety-rope. Fix the
safety-rope at the correct fixation points only. The safety-rope must never be fixed at the transport handles!
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly
fastened.
The maximum ambient temperature Ta = 45° C must never be exceeded.
Operate the device only after having become familiarized with its functions. Do not permit operation by
persons not qualified for operating the device. Most damages are the result of unprofessional operation!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasons!

!
!
4!
Never!remove!the!serial!barcode!from!the!device!as!this!would!make!the!guarantee!void.
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-
circuit, burns, electric shock, crash etc.
DESCRIPTION OF THE DEVICE
Features
Source
Light source: Osram Sirius HRI 230W discharge lamp
Led life: 3.000 hours
Luminous Flux: 10150lumen, 61200lux@20m
Control: Remote on/off via DMX
Ballast: switching mode power supply
Optical System
Beam angle: 2.5°
X/Y
Pan: 360° (4.0 sec) or 540°(3.58 sec), Tilt: 265° (2.8 sec)
16-bit resolution
Auto repositioning
Colors
14+open, interchangeable, indexable and bidirectional rainbow effect
New color bounce effect
Gobos
Outside 13.8mm, inside 6mm
8+ open custom interchangeable position for rotating gobo wheel
Real indexable and gobo shaking
Distinctive gobo animation effect
Features
DMX channels: 16/18/19
Color wheel: 14+1 colors
Rotating gobo wheel: 8+1 gobos
Motorized focus
Full range 0-100% dimmer
Various strobe
Rotating Effect wheel with 3 facets,8 facets prism and frost
RDM function to change DMX address, display flip, X/Y Reverse, show lamp voltage, current and power
consumption info.
Software upgrade via DMX
Hibernation when lost DMX for preset time
Indicate temperature info of base, arm and lamp
Fan speed auto change according to temperature
Display
24inch super nice LCD display with friendly English menu
Auto lock
Flip
Back-up communicating IC
Power
Max power consumption: 300W
Power supply: Electronic auto-ranging
Input voltage range: 100–240V, 50-60Hz

!
!
5!
!
Overview
(1) Objective lens
(2) Arm
(3) Base! !
(4) Handle
(5) Wireless indicator
(6) Display
(7) Microphone
(8) Left button
(9) Down buttom
(10) Enter button
(11) Up button
(12) Right button
(13) 3-PIN DMX input socket
(14) 3-PIN DMX output socket
(15) Power input
(16) Power output
(17) Fuseholder
(18) Power switch
1!
2!
3!
4!
5!
12!
7!
8!
9!
10!
11!
6!
13 14 15 16 17 18

!
!
6!
INSTALLATION
Inserting/Exchanging gobos
DANGER!
Install the gobos with the device switched off
only.
Unplug from mains
before!
If you wish to use other forms and patterns as the standard-gobos, or if gobos are to be exchanged, please
follow the instructions below:
CAUTION!
Never unscrew the screws of the rotating
gobo
as the ball bearing will otherwise be opened!
Remove the fixation-ring with an appropriate tool. Remove the gobo and insert the new gobo. Press the
fixation-ring together and insert it in front of the gobo.
Notes!
Slot-in gobo-system for exchanging gobos without
tools!
Inserting/Exchanging gobos as described
above.
Rigging
The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for
1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
This secondary safety attachment must be constructed in a way that no part of the installation can fall down if
the main attachment fails.
When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.

!
!
7!
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert before taking into operation for the first time and after changes before taking into operation another
time.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by a
skilled person once a year.
Procedure:
The projector should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to)
calculating working load limits, installation material being used, and periodic safety inspection of all
installation material and the projector. If you lack these qualifications, do not attempt the installation yourself,
but instead use a professional structural rigger. Improper installation can result in bodily injury and.or
damage to property.
The projector has to be installed out of the reach of people.
If the projector shall be lowered from the ceiling or high joists, professional trussing systems have to be used.
The projector must never be fixed swinging freely in the room.
Caution: Projectors may cause severe injuries when crashing down! If you have doubts concerning the
safety of a possible installation, do NOT install the projector!
Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector's
weight.
DANGER OF FIRE!
When installing the device, make sure there is no highly-inflammable
material (decoration articles, etc.) within a distance of min. 0.5
m.
CAUTION!
Use an appropriate clamp to rig the fixture on the
truss.
Follow the instructions mentioned at the bottom of the base.
Make sure that the device is fixed properly! Ensure that
the structure (truss) to which you are attaching the fixtures is
secure.
The Moving-Head can be placed directly on the stage floor or rigged in any orientation on a truss without
altering its operation characteristics (see the drawing).
The fixture’s base enables to be mounted in two ways.

!
!
8!
For overhead use (mounting height >100 cm), always install
an appropriate safety bond.
Please note: for overhead rigging in public or industrial areas,
a series of safety instructions have to be followed that this
manual can only give in part. The operator must therefore
inform himself on the current safety instructions and consider
them.

!
!
9!
The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety
precautions!
Install the safety bond by inserting the quick link in the hole on the bottom of the base. Pull the safety bond
over the trussing system etc. Insert the end in the quick link and tighten the fixation screw.
The maximum drop distance must never exceed 20 cm.
A safety bond which already hold the strain of a crash or which is defective must not be used again.
DANGER TO LIFE!
Before taking into operation for the first time, the installation has to be approved by an expert!
2 3
(1) Omega-holder
(2) Clamp
(3) Safety-rope 1
(4) Quick-lock fastener
4
Screw the clamp via a M12 screw and nut onto the Omega-holder.
Insert the quick-lock fasteners of the Omega-holder into the respective holes
on the bottom of the device. Tighten the quick-lock fasteners fully clockwise.

!
!
10!
DMX-512 connection / connection between fixtures
Projector 1 Projector 2 Projector 3
Starting address 1 Starting address 20 Starting address 39
120 Ohms DMX-512 Controller
The wires must not come contact with each other, otherwise
the fixtures will not work at all, or will not work properly.
Please note, the starting address depends upon which controller is being used.
Only use a DMX-cable and 3-pin XLR-plugs and connectors in order to connect the controller with the fixture
or one fixture with another.
Occupation of the XLR-connection:
If you are using controllers with this occupation, you can connect the DMX-output of the controller directly
with the DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other
XLR-outputs, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always
connect one output with the input of the next fixture until all fixtures are connected.
Caution: At the last fixture, the DMX-cable has to be terminated. Plug the terminator with a 120 Ωresistor
between Signal (–) and Signal (+) in the DMX-output of the last fixture.

!
!
11!
Connection with the mains
Connect the device to the mains with the enclosed power supply cable.
The occupation of the connection-cables is as follows:
Cable
Pin
International
Brown
Live
L
Blue
Neutral
N
Yellow/Green
Earth
The earth has to be connected!
If the device will be directly connected with the local power supply network, a disconnection switch with a
minimum opening of 3 mm at every pole has to be included in the permanent electrical installation.
The device must only be connected with an electric installation carried out in compliance with the IEC-
standards. The electric installation must be equipped with a Residual Current Device (RCD) with a maximum
fault current of 30 mA.
Lighting effects must not be connected to dimming-packs.
The device is equipped with a lockable power input connector. Plug in the power cord and turn it to the right
until it locks. Plug the power cord into a grounded electrical outlet that matches the rated voltage of the
machine.
OPERATION
With the power switch, you can switch the device on and off.
After you connected the effect to the mains, the fixture starts running. During the reset, the motors are
trimmed and the device is ready for use afterwards.
Stand Alone operation
In the Stand Alone mode, the model can be used without controller.
Disconnect the fixture from the controller and call the internal program.
Please refer to the instructions under Control Board.
DMX-controlled operation
You can control the projectors individually via your DMX-controller. Every DMX-channel has a different
occupation with different features. The individual channels and their features are listed under DMX-protocol.
Addressing
The Control Board allows you to assign the DMX starting address, which is defined as the first channel from
which the fixture will respond to the controller.
If you set, for example, the address to channel 20, the fixture will use the channel 20 to 38 for control.
Please, be sure that you don’t have any overlapping channels in order to control each fixture correctly and
independently from any other fixture on the DMX-chain.
If several fixture are addressed similarly, they will work synchronically.
Press the Up/Down-buttons for setting the desired starting address. Now you can start operating the fixture
via your lighting controller.
!

!
!
12!
Note:
After switching on, the device will automatically detect whether DMX 512 data is received or not. If there is
no data received at the DMX-input, the display will flash.
This situation can occur if:
- the XLR plug (cable with DMX signal from controller) is not connected with the input of the device.
- the controller is switched off or defective, if the cable or connector is defective or the signal wires are swap
in the input connector.
Note:
It’s necessary to insert the XLR termination plug (with 120 Ohm) in the last lighting in the link in order to
ensure proper transmission on the DMX data link.
DMX-protocol
Channel
name
function
Min
DMX
Max
DMX
St
Ex1
Ex2
1
1
1
Pan
Pan Coarse
0
255
2
2
Pan fine
Pan Fine
0
255
2
3
3
Tilt
Tilt Coarse
0
255
4
4
Tilt fine
Tilt Fine
0
255
3
5
5
Movment
Speed
fastest to Slowest
0
255
6
Movment
Function
Normal
0
15
Movement With Backout
16
31
TBD
32
255
4
6
7
Shutter
Function
Normal Shutter Functions
0
15
Pulse-effect Forward
16
31
Pulse-effect Reverse
32
47
Random Strobe
48
63
TBD
64
255

!
!
13!
!
5
7
8
Shutter
Normal Shutter Functions
Close
0
31
Strobe Rate (slow to fast)
32
223
Open
224
255
Pulse-effect Forward
Close
0
31
Strobe Rate (slow to fast)
32
223
Open
224
255
Pulse-effect Reverse
Close
0
31
Strobe Rate (slow to fast)
32
223
Open
224
255
Random Strobe
Close
0
31
Strobe Rate (slow to fast)
32
223
Open
224
255
6
8
9
Dimmer
Dimmer(Close to Open)
0
255
7
9
10
Color
Function
Indexed
0
15
Indexed With BackOut
16
31
Forward Spin
32
47
Reverse Spin
48
63
Continuous
64
79
Color Bounce
80
111
TBD
112
255

!
!
14!
!
8
10
11
Color
Indexed & Indexed With BackOut&Color Bounce
Position 1 (Open)
0
16
Position 2
17
33
Position 3
34
50
Position 4
51
67
Position 5
68
84
Position 6
85
101
Position 7
102
118
Position 8
119
135
Position 9
136
152
Position 10
153
169
Position 11
170
186
Position 12
187
203
Position 13
204
220
Position 14
221
237
Position 15
238
255
Forward Spin
Stop to fastest
0
255
Reverse Spin
Stop to fastest
0
255
Continuous
Positioning from 0-360 degrees
0
255
9
11
12
Rot
Gobo
Function
Indexed
0
15
Indexed With BackOut
16
31
Forward Spin
32
47
Reverse Spin
48
63
Continuous
64
79
Shake
80
95
TBD
96
255
10
12
13
Rot
Gobo
Indexed & Indexed With Backout&Shake
Position 1 (Open)
0
27
Position 2
28
55
Position 3
56
83
Position 4
84
111
Position 5
112
139
Position 6
140
167
Position 7
168
195
Position 8
196
223
Position 9
224
255
Forward Wheel Spin
Stop to fastest
0
255
Reverse Wheel Spin
Stop to fastest
0
255
Continuous
Positioning from 0-360 degrees
0
255

!
!
15!
!
11
13
14
Gobo
Rot
Function
Continuous
0
15
Forward Spin
16
31
Reverse Spin
32
47
Forward Animate Rotate
48
63
Forward Animate Rotate With Backout
64
79
Reverse Animate Rotate
80
95
Reverse Animate Rotate With Backout
96
111
TBD
112
255
12
14
15
Gobo
Rot
Continuous
Positioning from 0-360 degrees
0
255
Forward Spin
Stop to fastest
0
255
Reverse Spin
Stop to fastest
0
255
Forward Animate Rotate & Forward Animate Rotate
With Backout
Stop to fastest
0
255
Reverse Animate Rotate & Reverse Animate Rotate
With Backout
Stop to fastest
0
255
13
15
16
Prism
Indexed & Indexed With Backout
Position 1 (Open)
0
63
Position 2
64
127
Position 3
128
191
Position 4
192
255
14
16
17
Prism
Rot
Forward Spin
Stop to fastest
0
127
Reverse Spin
Stop to fastest
128
255
15
17
18
Focus
Continuous
Focus In to Focus Out
0
255
16
18
19
Control
Normal
0
7
Reset All
8
15
Pan&Tilt Reset
16
23
Color Reset
24
31
Gobo Reset
32
39
Shutter Reset
40
47
Other Reset
48
55
Display Off
56
63
Display On
64
71
Lamp Off
72
79
Lamp On
80
87
Hibernation
88
95
TBD
96
255

16
Control Board
The Control Board offers several features: you can simply set the starting address, run the pre-programmed
program or make a reset.
The main menu is accessed by pressing Enter until the display is lit. Browse through the menu by pressing
the arrow buttons (up, down, left, right). Press Enter in order to select the desired menu. You can change
the selection by pressing the arrow buttons. Press Enter in order to confirm. The functions provided are
described in the following sections.
Default settings shaded. 1 Basic Reload / 2 Program Reload / 3 Private Reload
Connect
DMX Address XXX DMX address setting
Wireless Wireless Enabled
Light
Turn On/Off ON/OFF Lamp On
Automatic ON/OFF Lamp On/off when power on
DMX Control ON /OFF DMX control or not
Max Temperature 80~139 , 120 /176~282 , 248 Lamp off if temperature
continuously over for 5
minutes
Lamp Adjust PAN…… Adjust value of channel
Information
Time Info. Current XXXX(Hours)
Fixture Life XXXX(Hours)
Fixture boot time
Fixture total run time
Temperature Near Lamp Temp (depends on fixture) Temperature Sensors
Fans Speed Near Lamp Fan (depends on fixture) Fan speed Sensors
Channel Value PAN…… D isplay value of channel
Error Message Pan,Tilt…… Error channels
Fixture Model xxxxxxxxxxxx Display model brand
and model
Software Ver 1U01 V1.0.00
2U01 V1.0.00
:
Version of each IC

17
Set
Reset All
Pan&Tilt
Colors
Gobos
Shutter
Others
Reset all
Reset Pan&Tilt
Reset Colors
Reset Gobos
Reset Shutter
Reset Others
Movment Pan Reverse
Tilt Reverse
Pan Degree
Encoders
Pan/Tilt Mode
ON/OFF
ON/OFF
630/ 540
ON/OFF
Stand /Smooth
Pan Reverse
Tilt Reverse
Choose Pan Degree
Encoder wheel on/off
Choose pan/tilt mode
UI Set Mic Sens.
No Signal
Temperature. C/F
Fans Mode
Hibernation
Backlight
Flip Display
DisplayBright
Brand Show
Key Lock
0~99%,60%
Close/Hold/Auto/Music
Fahrenheit / Celsius
Auto Speed /High Speed
OFF, 01M~99M 15M
02~60m 02m
ON/OFF
00~31 10
ON/OFF
ON/OFF
Sensitivity of Mic
Mode when no signal
Temperature at /
Fans mode
Sleeping mode
Show backlight time
Display 180reverse
Display Brightness
Show brand or not
Key lock on/off
Users User Mode Standard
Extended 1
Extended 2
User
Standard mode(16bit)
Extended mode 1
Extended mode 2
User program mode
Edit User Max Channel = XX
PAN = CH01
:
Edit users mode
Calibration -Password-
Color
:
=XXX
=XXX
:
Password:050
Calibrate channel value
Fixture ID Name
-Password-
PID Code
Name
Password:050
Set PID of RDM
Wireless Set DMX On Cable
Reset Connect
ON/OFF
ON/OFF
DMX Send Out
Reset Connect
Reload Default Basic Reload( )
Program Reload( )
---Password---
Private Reload( )
All Reload
ON/OFF
ON/OFF
XXX
ON/OFF
ON/OFF
Basic Reload
Program Reload
Password:050
Private Reload
All Reload

18
Connect
DMX address setting
With this function, you can adjust the desired DMX-address via the Control Board.
Select “DMX Address“ by pressing Up or Down.
Press the Enter-button, adjust the DMX address by pressing Up or Down.
Press the Enter-button to confirm.
Wireless
With this function, you can enter wireless mode, then no need signal cable connection, in this mode
signal still transmitted by cable if the signal cables are connected, if want to send signal via wireless
cables must be disconnected.
Light
MaxTemperate
With this function you can set the inside temperature at which the projector will automatically switch the
lamp off. Press Up or Down to select the maximum inside temperature between 80 °C and 139 °C.
Inside temperatures below 90 °C are not critical. 90 °C and more should lead to the lamp being
switched off. Please note that the outside temperature should not exceed 45 °C.
Information
Program
Play DMX Reveice
Slave Reveice
Sequence
Music
Slave Reveice 1,2,3
Master / Alone
Master / Alone
DMX Receive
Choose slave position
RunSequence
Music mode
Select Chase Chase Part 1
Chase Part 2
Chase Part 3
Chase 1 ~ 8 Chase 1
Chase 1 ~ 8 Chase 2
Chase 1 ~ 8 Chase 3
Select and run
auto program
Edit Chase Chase 1
:
Chase 8
Chase Test
Step 01
Step 64
=SCxxx
=SCxxx
Test
Beginning scene
Ending scene
Edit Scenes Edit Scene 001
~ Edit Scene
250
Pan,Tilt, ……
--Fade Time --
--Scene Time--
DMX Input
=xxx
=xxx
=xxx
Input manual scene
Modify manually fading
time
Modify manually scene
time
Input scene from
exterior controller
Scenes Record ScXX=>ScXX Auto Input scenes

!
!
19!
Time information Current
With this function, you can display the temporary running time of the device from the last power on.
The display shows “XXXX”, “X“ stands for the number of hours. The counter is reset after turning the
device off.
Fixture Life
With this function, you can display the running time of the device. The display shows “XXXX”, “X“
stands for the number of hours.
Temperature Near lamp Temp
With this function you can display the temperature in the projector-head in degree
Celsius/degree Fahrenheit.
...
Fan speed
With this function you can display the current fan speed. The display shows “XXXX”, “X“ stands for Hz.
Initial status
With this function, you can display with which value the respective channels will start.
Error channels
With this function, you can display the channel errors.
Fixture Model
With this function, you can display the model number and brand of the fixture.
Software version
With this function you can display the software version of each IC.
• Select “Software ver.” by pressing Up or Down.
• Press the Enter-button, the display shows e.g. “1U01 VX.X.XX”, “X.X.XX“ stands for the version number.
Set
Reset
With this function you can reset the device via the Control Board. You can select the different Reset-
functions by pressing Up or Down.
Movement
PAN Reverse
With this function you can reverse the PAN-movement.
TILT Reverse
With this function you can reverse the TILT-movement.
PAN degree
With this function you can select thePAN-degree.
• Select “PAN degree” by pressing Up or Down.
• Press the Enter-button, the display shows “540”.
• Press Up or Down to select the desired degree between “540” and “630”.
• Press the Enter-button to confirm.
Automatic PAN/TILT calibration
With the function "Encoders" you can calibrate the PAN/TILT movement to the correct starting position.
Adjust PAN/TILT speed
With this function you can define the PAN/TILT speed. You can select one of two different modes.
UI Set