TEDIA PCE-1603 User manual

General description
The PCE-1603 board is used to conditioning TTL/HC signals of the TEDIA DAQ
PC card digital ports to external equipments with technological signal levels and
contains sixteen input channels organized into two blocks of eight channels.
As standard, the input channels are designed for DC signals up to 32 V both
polarities, but as an option filter capacitors can be added in order to add
compatibility with AC signals with a frequency of 50 Hz.
All channels work as non-inverting; the presence of the input voltage is represented
by the "H" level on the PC card signal.
General instructions for use
The PCE-1603 may be used only according to the manufacturer's recommendations
given in this manual or other general standards and only such a way, that its failure
caused by any reason will not be dangerous to any person or property.
Installation
The PCE-1603 is designed to be placed into a free slot for expansion cards, the
length of the ribbon cables requires a position adjacent to the control PC card.
The board can be used in an environment with operating temperature -10~60 °C and
relative humidity up to 90%, noncondensing and normal levels of pollution.
Specifications
Digital inputs:
input voltage - level L: < 3 VDC (= level L on the PC card signal)
input voltage - level H: > 10 VDC (= level H on the PC card signal)
maximum input voltage: ±32 VDC (±50 VDC max. 10 ms)
input impedance: 10 kOhm approx.
signal delay: < 0.2 ms
isolation voltage: 1000 VDC (inputs against the PC card port)
General:
recommended cable length: 10 m max. (isolated inputs)
dimensions of board: 80 x 60 mm approx.
power supply: 5 V (powered from PC card port)
current consumption: 30 mA max.
KX1/KX2 connectors pin assigment
identical to the pin assigment of DIO port connectors (refer to the PC card manual)
K1 connector pin assigment (D-Sub 9, male), the board generates KX1 signals
DIN00 (input signal, channel 0) C1 C6 DIN01 (input signal, channel 1)
DIN02 (input signal, channel 2) C2 C7 DIN03 (input signal, channel 3)
DIN04 (input signal, channel 4) C3 C8 DIN05 (input signal, channel 5)
DIN06 (input signal, channel 6) C4 C9 DIN07 (input signal, channel 7)
I_COM0 (DIN common signal) C5
Note: Since the inputs accepts signal of both polarities, the I_COM0 signal can be
connected to GND (for "PNP" type outputs) or +24 V (for "NPN" type outputs).
K2 connector pin assigment (D-Sub 9, male), the board generates KX2 signals
DIN10 (input signal, channel 0) C1 C6 DIN11 (input signal, channel 1)
DIN12 (input signal, channel 2) C2 C7 DIN13 (input signal, channel 3)
DIN14 (input signal, channel 4) C3 C8 DIN15 (input signal, channel 5)
DIN16 (input signal, channel 6) C4 C9 DIN17 (input signal, channel 7)
I_COM1 (DIN common signal) C5
Note: Since the inputs accepts signal of both polarities, the I_COM1 signal can be
connected to GND (for "PNP" type outputs) or +24 V (for "NPN" type outputs).
K1
K2
KX1
KX2 DIN port of PC card
DIN port of PC card

Fig. 1. Simplified schematic of isolated inputs.
The PCE-1603 contains sixteen input channels organized into two blocks
of eight channels.
Note: Capacitors of 1 μF (enable the processing of AC signals with a frequency of
50 Hz or higher) are not fitted as standard and can be added as an option.
DINx0
DINx1 DIN port
10K
5K
DINx7 10K
5K
I_COMx
DINx2
(1μF)
(1μF)
of PC card
Manufacturing, sales office, service center and technical support:
TEDIA spol. s r. o.
Zabelska 12, 31200 Plzen, Czech Republic
phone/e-mail: https://www.tedia.eu/contacts
address:
PCE-1603
User Guide
(further information available at http://www.tedia.eu)
document revision: 02.2013, © 1994-2013 TEDIA®spol. s r. o.