TEDIA PCE-1601 User manual

General description
The PCE-1601 board is used to conditioning TTL/HC signals of the TEDIA DAQ
PC card digital ports to external equipments with technological signal levels and
contains eight input and eight output channels.
As standard, the input channels are designed for DC signals up to 32 V both
polarities, but as an option filter capacitors can be added in order to add
compatibility with AC signals with a frequency of 50 Hz.
The output channels are solved by individually isolated switching relays.
All channels work as non-inverting; the presence of the input voltage is represented
by the "H" level and the "H" level at the PC card output activates the signal switch.
General instructions for use
The PCE-1601 may be used only according to the manufacturer's recommendations
given in this manual or other general standards and only such a way, that its failure
caused by any reason will not be dangerous to any person or property.
Installation
The PCE-1601 is designed to be placed into a free slot for expansion cards, the
length of the ribbon cables requires a position adjacent to the control PC card.
The board can be used in an environment with operating temperature -10~60 °C and
relative humidity up to 90%, noncondensing and normal levels of pollution.
Specifications
Digital inputs:
input voltage - level L: < 3 VDC (= level L on the PC card signal)
input voltage - level H: > 10 VDC (= level H on the PC card signal)
maximum input voltage: ±32 VDC (±50 VDC max. 10 ms)
input impedance: 10 kOhm approx.
signal delay: < 0.2 ms
isolation voltage: 1000 VDC (inputs against the PC card port)
Digital outputs:
switching voltage: 30 VDC max.
100 VAC max.
switching current: 500 mA max.
signal delay: < 5 ms
isolation voltage: 200 VDC/VAC (outputs against the PC card port)
100 VDC/VAC (relay contacts to each other)
General:
recommended cable length: 10 m max. (isolated inputs/outputs)
dimensions of board: 93 x 60 mm approx.
power supply: 5 V (powered from PC card port)
current consumption: 400 mA max.
Note: Values marked as "RMS" indicate the effective AC value with the frequency
50Hz.
KX1/KX2 connectors pin assigment
identical to the pin assigment of DIO port connectors (refer to the PC card manual)
K1 connector pin assigment (D-Sub 25, male), controlled by KX1 signals
DOUT00_RL0_NO (relay contact) C1 C14 DOUT00_RL0_CM (relay contact)
DOUT00_RL0_NC (relay contact) C2 C15 DOUT01_RL1_NO (relay contact)
DOUT01_RL1_CM (relay contact) C3 C16 DOUT01_RL1_NC (relay contact)
DOUT02_RL2_NO (relay contact) C4 C17 DOUT02_RL2_CM (relay contact)
DOUT02_RL2_NC (relay contact) C5 C18 DOUT03_RL3_NO (relay contact)
DOUT03_RL3_CM (relay contact) C6 C19 DOUT03_RL3_NC (relay contact)
DOUT04_RL4_NO (relay contact) C7 C20 DOUT04_RL4_CM (relay contact)
DOUT04_RL4_NC (relay contact) C8 C21 DOUT05_RL5_NO (relay contact)
DOUT05_RL5_CM (relay contact) C9 C22 DOUT05_RL5_NC (relay contact)
DOUT06_RL6_NO (relay contact) C10 C23 DOUT06_RL6_CM (relay contact)
DOUT06_RL6_NC (relay contact) C11 C24 DOUT07_RL7_NO (relay contact)
DOUT07_RL7_CM (relay contact) C12 C25 DOUT07_RL7_NC (relay contact)
- - - C13
K2 connector pin assigment (D-Sub 9, male), the board generates KX2 signals
DIN00 (input signal, channel 0) C1 C6 DIN01 (input signal, channel 1)
DIN02 (input signal, channel 2) C2 C7 DIN03 (input signal, channel 3)
DIN04 (input signal, channel 4) C3 C8 DIN05 (input signal, channel 5)
DIN06 (input signal, channel 6) C4 C9 DIN07 (input signal, channel 7)
I_COM0 (common signal of inputs) C5
Note: Since the inputs accepts signal of both polarities, the I_COM0 signal can be
connected to GND (for "PNP" type outputs) or +24 V (for "NPN" type outputs).
K1
K2
KX1
KX2 DIN port of PC card
DOUT port of PC card

Fig. 1. Simplified schematic of relay outputs (one channel out of eight).
Fig. 2. Simplified schematic of isolated inputs.
Note: Capacitors of 1 μF (enable the processing of AC signals with a frequency of
50 Hz or higher) are not fitted as standard and can be added as an option.
RLx_NO
RLx_NC
RLx_CM
+5 V
DOUT port
of PC card
DIN00
DIN01 DIN port
10K
5K
DIN07 10K
5K
I_COM0
DIN02
(1μF)
(1μF)
of PC card
Manufacturing, sales office, service center and technical support:
TEDIA spol. s r. o.
Zabelska 12, 31200 Plzen, Czech Republic
phone/e-mail: https://www.tedia.eu/contacts
address:
PCE-1601
User Guide
(further information available at http://www.tedia.eu)
document revision: 02.2013, © 1994-2013 TEDIA®spol. s r. o.