Tek-Trol TEK-WAVE 4300B User manual

Quick Start Guide
TEK-WAVE 4300B
FMCW Bluetooth Radar Level Transmitter
796 Tek Drive, Crystal Lake, IL 60014 USA [phone] | [phone] [phone] www.tek-trol.com

796 Tek Drive, Crystal Lake, IL 60014 USA [phone] | [phone] [phone] www.tek-trol.com
Quick Start Guide
1. Before you begin
2. Unpack
3. Dimensional Drawing
This guide provides basic guidelines to assist you in quickly getting started.
Installation of the device must be carried out by trained, qualied specialists authorized
to perform such work by the facility’s owner operator. The specialist must have read and
understood these Operating Instructions and must follow the instructions they contain.
When using the measuring device in hazardous areas, installation must comply with the
corresponding national standards and regulations.
Tek-Wave 4300B FMCW Bluetooth Radar Level Transmitter
Fig 1: Front view
1¼”(32mm)
3¼”(81mm)
7/8”(23mm)
4¼”(107mm)
1.5" NPT
3/4" NPT

Tek-Wave 4300B
Technology Solutions
Fig 2: Mounting Bracket Side Angle
13”
21.5”
8”
17.25”
• Mounting brackets
Fig 3: Mounting Bracket Back Angle
R
3
/
32
”
4” 4”
2”
2.25”

796 Tek Drive, Crystal Lake, IL 60014 USA [phone] | [phone] [phone] www.tek-trol.com
Quick Start Guide
Fig 4: Mounting Bracket Top Angle
6”2.25”
3.5”
R 3/32”
6”
1.5” NPT
2”
2”
Fig 5: Mounting Bracket
Plate Thickness
1/25”

Tek-Wave 4300B
Technology Solutions
• The Tek-Wave 4300B should not be mounted closer than 8”(200mm) to the vessel wall.
• The Tek-Wave 4300B is not mounted in the center because interference can cause signal loss.
• The Tek-Wave 4300B is not mounted above the ll stream.
• A weather protection cover is recommended to protect the instrument from sun or rain.
• The radar antenna should be vertical to measure the media surface.
Table 1: Wire Description
Fig 6: Wiring Connections
Fig 7: General Mounting Position
4. Power Supply
+
_
Wire Color Function
Brown Voltage +
White Voltage – (4-20mA)
Green Modbus RS485 A
Yellow Modbus RS485 B
Gray Ground
5. Installation
• General mounting conditions
8”(200mm)

796 Tek Drive, Crystal Lake, IL 60014 USA [phone] | [phone] [phone] www.tek-trol.com
Quick Start Guide
• Stirring Fan in Vessel
• Reduction of Interference Echoes
If there is a stirring fan in the vessel:
• The instrument should be mounted at 1/2 of the distance from the inner wall to the stirring fan.
• Carry out false echo storage to reduce the interference from the stirring fan.
Radar signals can spread by mounting metallic at a slope, which reduces the interference echoes.
Fig 8: Mounting Position for Stirring Fan in Vessel
Fig 9: Mounting Position for Interference Echoes Reduction

Tek-Wave 4300B
Technology Solutions
• Mounting with Bracket
• The instrument should be mounted at 1/2 of the distance from the inner wall to the stirring
fan.
• Carry out false echo storage to reduce the interference from the stirring fan.
Fig 10: Mounting with Bracket
8”(200mm)
• Please install “Blueset”in your smart phone.
• Allow the APP to utilise the location and storage functions.
• Hold down the APP till it indicates“APP info”.
• ”APP info”> “Permissions”>”Location”>”Allow”
• ”APP info” >”Permissions”>”Storage”>”Allow”
• Start APP.
• Select Device“SENSOR 01”.
• Bluetooth Setup (Android Only)
6. Operations (Setup with Smartphone/Tablet (Bluetooth)
or Modbus Software)
)

796 Tek Drive, Crystal Lake, IL 60014 USA [phone] | [phone] [phone] www.tek-trol.com
Quick Start Guide
• Setup
• Main Menu
• You can nd measuring distance, level and ratio on the main menu.
• Using Setting Menu, you can set the parameters.
• Setting Parameters
• Setting Parameters consist for sub menus
Note: - If the 4300B is having any Alarm like HH or LL. the output current will be either 20.5 mA
or 3.8 mA.at this point the Bluetooth app will starts connect/disconnect or get hang to previous
screen until the unit reaches to normal operation.
Trouble shooting: Close the app and relaunch keep search for the 4300B unit repeatedly.

Tek-Wave 4300B
Technology Solutions
• Quick Setup
• Check Echo Curve
• Set Measuring Range
• Please enter“Quick Setup” to set the measuring range.
• Write minimum and maximum range and press to save data.
• Write Tag number as per your application and press to save data.
• You can upload data from the device by pressing “Upload Data”.
• Enter menu with echo curve by entering “Level Conrm”.
• If you set a new measuring range and want to change the X range, please re-write the
data on the End and save it by Refresh Range

796 Tek Drive, Crystal Lake, IL 60014 USA [phone] | [phone] [phone] www.tek-trol.com
Quick Start Guide
• Check Fake Echo
• If there is an obstacle inside the tank that generates a fake echo, you will need to
create a fake echo.
• Please use “+” or “-” to move the line indicated by the arrow to set the fake echo
position of false echo and press behind Create and you will get new double
echo curve.

Tek-Wave 4300B
Technology Solutions
• Basic Setup
• You can set the following parameters according to eld conditions.
• You can also upload data from the device by“Upload Data”.
• For most applications, the device can work properly after the setup of the above two
menus.
• For more menu information, please contact us, and you can also refer to the menu
overview.
*Note: The distance between device and smartphone should be not more than 25’ to get better signal
communication.
• Connect the 4300B to the 4300B-USB tool and power the 4300B.
• Modbus Software Setup

796 Tek Drive, Crystal Lake, IL 60014 USA [phone] | [phone] [phone] www.tek-trol.com
Quick Start Guide
• Launch the 4300B Modbus Program.
• When the program opens. Click Connect to Poll the 4300B.
• It will take the software a few moments to nd the 4300B.

Tek-Wave 4300B
Technology Solutions
• When the Modbus program connects to the 4300B, there will be two red ashing lights on
the 4300B-USB tool and a green Dot in the lower left side of the screen. The 4300B process
data will appear on the bottom of the screen.
• From the Quick Setup screen the Max and Min range can be set up the Max range is your
4mA and the min range is you 20mA. You can also look at the Echo Curve on this screen.

796 Tek Drive, Crystal Lake, IL 60014 USA [phone] | [phone] [phone] www.tek-trol.com
Quick Start Guide
• In the Basic Setup screen the following parameter can be adjusted.
• In the System screen you can simulate a mA signal to make use you output is setup correctly
at your PLC or Scada.

Tek-Wave 4300B
Technology Solutions
• In the Communication screen the HART and Mobus communication paraments can be
changed.
• The Security screen will allow the following parameters to be changed.

796 Tek Drive, Crystal Lake, IL 60014 USA [phone] | [phone] [phone] www.tek-trol.com
Quick Start Guide
• The Info screen will give you all the manufacturing information about the 4300B.
• After you have uploaded all the modications to the 4300B, click Disconnect and remove
the 4300B from your PC.

Tek-Wave 4300B
Technology Solutions
7. Menu Tree

Tek-Wave 4300B
Tek-DPro Flow Solutions
Tek-Trol LLC
Tek-Trol Solutions BV Tek-Trol Middle East FZE
PO Box 121 Windsor, Colorado
80550, USA
Sales: [phone]
796 Tek Drive Crystal Lake, IL
60014, USA
Sales: [phone]
Florijnstraat 18, 4879 AH
Etten-Leur, Netherlands
Sales: [phone]
SAIF Zone, Y1-067, PO BOX No.
21125, Sharjah, UAE
Sales: [phone]
Technology Solutions
Support: [phone] Email: [e-mail] www.tek-trol.com