Teknik 5420285 User manual

www.teknikoffice.co.uk
Get all organized
and stu.
Storage Stand
Hampstead Park Collection | Model 5420285
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-24
25-28
29-32
33-34
35
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D UPPER BACK (1)
E SHELF (1)
F DRAWER BRACE (1)
G LOWER BACK (1)
H FRONT BOTTOM (1)
I REAR BOTTOM (1)
J BACK (1)
K BRACE (2)
LLEFT FRONT/RIGHT
REAR LEG (2)
MRIGHT FRONT/LEFT
REAR LEG (2)
NLEFT SMALL
DRAWER SIDE (1)
O SMALL DRAWER BACK (1)
PRIGHT SMALL
DRAWER SIDE (1)
QLEFT LARGE
DRAWER SIDE (1)
R LARGE DRAWER BACK (1)
SRIGHT LARGE
DRAWER SIDE (1)
T DRAWER BRACE (2)
U SMALL DRAWER FRONT (1)
V LARGE DRAWER FRONT (1)
W DRAWER BOTTOM (2)
Pae 3
A
B
C
D
E
F
G
H
I
J
K
K
L
L
M
M
N
OP
Q
RS
T
T
U
V
W
W

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Pae 4
SMALL HIDDEN
CAM - 12
2
LARGE HIDDEN
CAM - 32
1
AA EXTENSION RAIL - 2 BB EXTENSION SLIDE - 2
(EXTENSION SET
SHOWN SEPARATED)
ANGLED HEAD
CAM SCREW - 32
3
Anled head
STRAIGHT HEAD
CAM SCREW - 12
4
Straiht head
NAIL - 22
9
APPLIQUE CARD - 1
7
LONG WOOD
DOWEL - 28
5
SHORT WOOD
DOWEL - 4
610 KNOB  2
11 LONG FILE
GLIDE - 1 12 SHORT FILE GLIDE - 2 13 FRONT FILE GLIDE  1 14 FILE HANGER  2
GROMMET - 1
8
15 BLACK 112" FLAT HEAD SCREW  14 16 BLACK 78" MACHINE SCREW  2
17 BLACK 12" PAN HEAD SCREW  16
LEFT CABINET
RAIL - 1
DD
RIGHT CABINET
RAIL - 1
CC
LEFT DRAWER
SLIDE - 1
FF
RIGHT DRAWER
SLIDE - 1
EE
BLACK 1/2" FLAT HEAD SCREW - 12
18

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push thiirty-two LARGE HIDDEN CAMS (1) into the TOP (C),
UPPER BACK (D), SHELF (E), DRAWER BRACE (F), LOWER
BACK (G), BOTTOMS (H and I), and BRACES (K), and
LEGS (L and M).
å NOTE: Be sure to push the LARGE HIDDEN CAMS
completely into the lare holes of the LEGS. The arrow
in the LARGE HIDDEN CAM must be pointin toward the
hole in the top surface of the LEGS.
Pae 5
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
Arrow
Arrow (32 used)
1
11 C
D
F
G
E
H
I
K
K
Arrow
M
L
1
This unit is not intended for
bedroom clothin storae.
Caution

Step 2
Anled head
3
å Turn thirty-two ANGLED HEAD CAM SCREWS (3) into the
ENDS (A and B), UPPER BACK (D), BOTTOMS (H AND I),
and LEGS (L and M).
(32 used)
Pae 6
A
B
H
I
L
L
M
M
Remember:
Rihty tihty.
Lefty loosey.
D

Step 3
å Push twenty-eiht LARGE WOOD DOWELS (5) into
the edes of the TOP (C), UPPER BACK (D), SHELF (E),
LOWER BACK (G), BOTTOMS (H and I), BRACES (K), and
LEGS (L and M).
å Push four SMALL WOOD DOWELS (6) into the LEGS (L and M).
5
5
5
5
Pae 7
H
I
E
D
G
C
K
K
5
L
L
M
M
6

å Fasten the TOP (C) to the UPPER BACK (D). Tihten two
LARGE HIDDEN CAMS.
å NOTE: Be sure the LARGE WOOD DOWEL in the TOP
inserts into the hole in the UPPER BACK.
Step 4
C
D
Pae 8
Surface with HIDDEN CAMS
1
2

Step 5
å Fasten the SHELF (E) to the UPPER BACK (D). Use two
BLACK 1-1/2" FLAT HEAD SCREWS (15).
å NOTE: Be sure the LARGE WOOD DOWEL in the UPPER
BACK inserts into the hole in the SHELF.
D
E
Pae 9
BLACK 1-1/2" FLAT HEAD SCREW
(2 used in this step)
15
Surface with HIDDEN CAMS

å Fasten the FEET (L and M) to the BOTTOM BRACES (K).
Tihten four LARGE HIDDEN CAMS.
å NOTE: Be sure the LARGE WOOD DOWELS in the
BRACES insert into the holes in the LEGS.
å Fasten a LEG/BRACE assembly to the FRONT BOTTOM (H).
Tihten four LARGE HIDDEN CAMS.
å Fasten the other LEG/BRACE assembly to the REAR
BOTTOM (I). Tihten four LARGE HIDDEN CAMS.
Step 6
Pae 10
K
K
K
K
H
I
M
M
M
M
L
L
L
L
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
Surface without HIDDEN CAMS
Surface with HIDDEN CAMS
1
2
Surface with HIDDEN CAM
Surface with HIDDEN CAM

å Separate the EXTENSION SLIDES (BB) from the EXTENSION RAILS (AA) as shown in the enlared diaram below. Be
prepared, the parts are reasy.
å Fasten an EXTENSION RAIL (AA) to the LEFT END (B). Use three BLACK 1/2" PAN HEAD SCREWS (17).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL out to find the other two holes that line up with the holes in the END. Turn a SCREW
into those holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
å Fasten the LEFT CABINET RAIL (DD) to the LEFT END (B). Use three BLACK 1/2" FLAT HEAD SCREWS (18).
Step 7
Pae 11
Pull up or down on the black lever and pull the SLIDE from the RAIL.
AA
BB
BLACK 1/2" PAN HEAD SCREW
(3 used in this step)
17
AA
DD
B
Roller end
Open end
Rounded corner
Rounded corner
BLACK 1/2" FLAT HEAD SCREW
(3 used in this step)
18

Step 8
Pae 12
A
AA
CC
å Fasten the EXTENSION RAIL (AA) to the RIGHT END (A). Use three BLACK 1/2" PAN HEAD SCREWS (17).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL out to find the other two holes that line up with the holes in the END. Turn a SCREW
into those holes.
å Fasten the RIGHT CABINET RAIL (CC) to the RIGHT END (A). Use three BLACK 1/2" PAN HEAD SCREWS (17).
Roller end
Open end
Rounded corner
Rounded corner
BLACK 1/2" PAN HEAD SCREW
(3 used in this step)
17
BLACK 1/2" FLAT HEAD SCREW
(3 used in this step)
18

å NOTE: When fastenin parts to each other, be sure the LONG and SHORT WOOD DOWELS insert into the holes of the
adjoinin parts.
å Fasten the FRONT BOTTOM (H) to the LEFT END (B). Tihten the LARGE HIDDEN CAM.
å Fasten the REAR BOTTOM (I) to the LEFT END (B). Tihten the LARGE HIDDEN CAM.
å Fasten the LOWER BACK (G) to the LEFT END (B). Tihten the LARGE HIDDEN CAM.
å Fasten the DRAWER BRACE (F) to the LEFT END (B). Tihten two LARGE HIDDEN CAMS.
å Fasten the SHELF (E), UPPER BACK (D), and TOP (C) to the LEFT END (B). Tihten four HIDDEN CAMS.
Step 9
Pae 13
B
H
I
G
F
E
C
D1
2

å Fasten the RIGHT END (A) to the TOP (C), UPPER
BACK (D), SHELF (E), DRAWER BRACE (F), LOWER
BACK (G), and BOTTOMS (H and I). Tihten eiht LARGE
HIDDEN CAMS.
å NOTE: Be sure the LONG and SHORT WOOD DOWELS in
the adjoinin parts insert into the holes in the RIGHT END.
Step 10
Pae 14
A
HI
G
F
E
C
D
1
2

Step 11
Pae 15
J
å Carefully turn your unit over onto its front edes. Unfold
the BACK (J) and lay it over your unit.
å Make equal marins alon all three edes of the BACK (J). Push
on opposite corners of your unit if needed to make it "square".
å Fasten the BACK (J) to your unit usin the NAILS (9).
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution
Unfinished surface
NAIL
(22 used in this step)
9
Side Step: Make
nachos. (Optional, but
recommended.)

Step 12
å Turn twelve STRAIGHT HEAD CAM SCREWS (4) into the
DRAWER FRONTS (U and V).
å Push twelve SMALL HIDDEN CAMS (2) into the lare holes in
the DRAWER SIDES (N, P, Q and R) and DRAWER BRACES (T).
Straiht head
4
2
Arrow
(12 used)
Q
S
T
T
N
P
(12 used)
Pae 16
U
V

å Fasten the RIGHT DRAWER SLIDE (EE) to the RIGHT SMALL
DRAWER SIDE (P) and the LEFT DRAWER SLIDE (FF) to the
LEFT SMALL DRAWER SIDE (N). Use six BLACK 1/2" FLAT
HEAD SCREWS (18).
Step 13
Pae 17
P
N
FF EE
Roller end
Roller end
BLACK 1/2" FLAT HEAD SCREW
(6 used in this step)
18
These holes
must be here.
These holes
must be here.

Step 14
å NOTE: Be sure the DRAWER BOTTOM (W) inserts into the roove of the DRAWER BACK
(O). Pae 18
1
2
å Fasten the SMALL DRAWER BACK (O) to the SMALL DRAWER SIDES (N and P) and DRAWER BRACE (U). Use six
BLACK 1-1/2" FLAT HEAD SCREWS (15).
å Fasten the SMALL DRAWER SIDES (N and P) and
DRAWER BRACE (T) to the SMALL DRAWER FRONT (U).
Tihten six SMALL HIDDEN CAMS.
å Slide a DRAWER BOTTOM (W) into the rooves
in the DRAWER SIDES (N and P) and SMALL
DRAWER FRONT (U).
Groove
Be sure the
DRAWER
BOTTOM inserts
into the DRAWER
BACK roove.
BLACK 1-1/2" FLAT HEAD SCREW
(6 used in this step)
15
N
N
N
P
P
P
T
U
U
W
W
O
U
12
3
Unfinished surface

å Fasten the EXTENSION SLIDES (BB) to the LARGE DRAWER
SIDES (Q and S). Use six BLACK 1/2" PAN HEAD SCREWS (17).
Step 15
Pae 19
S
Q
Open end
BLACK 1/2" PAN HEAD SCREW
(6 used in this step)
17
BB BB
These holes
must be here.

Step 16
å NOTE: Be sure the DRAWER BOTTOM (W) inserts into the roove of the LARGE DRAWER BACK
(R). Pae 20
1
2
å Fasten the LARGE DRAWER BACK (R) to the LARGE DRAWER SIDES (Q and S) and DRAWER BRACE (T). Use six
BLACK 1-1/2" FLAT HEAD SCREWS (15).
å Fasten the LARGE DRAWER SIDES (Q and S) and
DRAWER BRACE (T) to the LARGE DRAWER FRONT (V).
Tihten six SMALL HIDDEN CAMS.
å Slide a DRAWER BOTTOM (W) into the rooves
in the LARGE DRAWER SIDES (Q and S) and LARGE
DRAWER FRONT (V).
Groove
Be sure the
DRAWER
BOTTOM inserts
into the DRAWER
BACK roove.
BLACK 1-1/2" FLAT HEAD SCREW
(6 used in this step)
15
Q
Q
Q
S
S
S
T
T
VV
W
R
12
3
W
HH